Question about 1991 Plymouth Sundance

1 Answer

Dont wanna shift and when it does it shifts pretty hard

Its an automatic but whwn i come to a stop i usually put it in first or it dont wanna go

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Plymouth Master
  • 880 Answers

Detent cable way out of adjustment

Posted on Apr 18, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 kia senona shift lever hard to move


automatic or stick? if it is an automatic the shift sinkage may be bent or obstruckted. if it is a stick the clutch may be getting pretty worn out, the throw out bearing may be going bad or the forks may be bent.

Mar 19, 2014 | 2004 Kia Sedona

1 Answer

1993 gmc 1500 4x4 only shift into 4wheel when stopped


automatic hubs?? if so chances are they put grease into automatic hubs, which will cause sticking. hard apply, hard release..

Jan 27, 2013 | 1993 GMC Sierra K1500

1 Answer

My transmission in my 97 ford f150 wont move unless i put it in 4 low and now wont switch out of 4 low


Its Possible the chain in transfer case is stretched I had the same problem a used case was 250 at my local salvage yard

Nov 23, 2012 | Cars & Trucks

2 Answers

Okay for starters the car starts up fine and everything its just thatwhen i go to shift into drive or 1 or 2 and press on the gas it goes no where as if its in nuetral reverse does work , before all this...


first check the fluid level in the transmission,If the level is up where it needs to be check the shift lever at the transmission have someone shift it inside while you check outside to see if its actually moving the gear selector its possible its broken,if not then your transmission is bad.

Sep 03, 2011 | 1998 Mitsubishi 3000GT

1 Answer

I'm having a issue with my transmission on a 2004 venture, when it gets up to normal operating temperatures. Whwn the van shift from first to second and then from second to third, there tends be a clunk or...


The problem is probably a bad Electronic Pressure Solenoid (EPC). Have the computer scanned at a dealership or a transmission shop to verify this. The code will probably be a P1811. The P1811 code sets because the transmission takes longer than 0.65 seconds to shift, then the computer commands maximum line pressure to make the car shift as fast as possible to avoid burning the clutches. Replacing the EPC is an expensive job, however, you can install a shift kit to speed up the shifting, and probably fix the problem. The shift kit is available from a company called TransGo. If you go to www.transgo.com you can look up a distributor in your area. The kit you will need is the SK®4T65E. Installing the shift kit is pretty easy for the 'shade tree mechanic'; if you can change your own transmission fluid, you can most likely install this kit yourself.

Dec 17, 2010 | 2004 Chevrolet Venture Passanger

1 Answer

1997 ford ranger dont move in first gear


Usually the drum inside the first gear is damaged/burned.smell the fluid. Look for a new transmission then

Sep 26, 2017 | 1997 Ford Ranger SuperCab

1 Answer

2003 Nissan Sentra SE-R Spec-V clutch sticking and hard shifting


I am dealing with a very similar issue on my 03 Spec V , So far i noticed the clevis pin was loose and the locking hitch pin that slips thru it had fallen out . this caused the gears to not wanna engage due to the bolt behind the clevis which runs to the master cylinder was not getting pressed in when i pushed the clutch pedal in because the clevis pin was slippin on n off giving me no pressure up top .. I had to remove my lower dash panel in order to get visual n hand access to this pin , it is a tight spot to work in as well . May be easist to remove the 4 14mm bolts that hold yur driver seat in to give ya more room to work n stretch out ur arms

Sep 19, 2009 | 2003 Nissan Sentra

2 Answers

Trans shifts hard into 6 and out other gears shift fine


having the same problem... my car is an 03 as well... any solution yet? i flushed my tranny, put in synthetic, made sure the linkages were lubricated inside and outside the car, and still nothing.. theres no grinding, at all, its just really gummy

Apr 04, 2009 | 2001 Hyundai Tiburon

Not finding what you are looking for?
1991 Plymouth Sundance Logo

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...