Question about 1995 Jeep Wrangler

1 Answer

Noise when turning but not if front end is off ground

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

In both 2wd and 4wd? do no use 4wd on dry pavement free of ice or it will WIND up and make noise. (RTM)
get it serviced,
finding causes of noise, moving is dangerous
can be,
bad wheel bearings.
bad u-joints
driving on ice free pavement, noise is normal.
bad ball joints.
and other suspension parts up front, get it serviced./

Posted on Apr 18, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

What could be the problem?


If it's the front end that is shaking, check the ball joints, motor mounts and idler arm. Lift the front end of the van until tires are off the ground. Wiggle the front tires side to side checking for slack, use a pry bar or 2x4 to lift the wheels to check for slack. Everything should be tight. Have someone turn the steering wheel back and forth while the van is on the ground and look for loose connections in the front end. If any loose connections are found replace them. A mechanic can do a front end inspection for you for little cost if any at all. CV Joints generally do not cause any vibration when they are worn out; however, they will cause a lot of clicking noise when you turn corners once they have worn out.

Dec 22, 2014 | 2003 Pontiac Montana

1 Answer

Noise in front end


Sounds like CV joint. Get both front wheels off the ground. start it up and and have someone listen for the source of the noise.

Aug 22, 2014 | 2012 Nissan Sentra 2.0 Sedan 2.0L 4-cyl....

1 Answer

My 2004 kia optima driver side front make a roaring noise while its rolling


Sounds like you have a wheel bearing problem. Jack up the front end so wheels are off the ground. put your hand on the spring on the strut then turn the wheel with the other hand. If the bearing is bad you will feel the vibration/rough spot in the spring. Noise will get louder or diminish when you peed up or slow down.

Apr 05, 2014 | 2004 Kia Optima

1 Answer

Steering sticking and noise from front end


it could be a pump fault. have some one at the front of the car watching the pump. some one sit in the drivers seat and parked up start engine and wiggle the steering wheel left and right see how the pump is acting. engine revs should drop and rise when doing this if no drop etc then the pump fins inside are warn. If this is all ok jack the front off the ground and put on stands, turn the steering to full on each side at a time and check the steering rack joints and balls and the condition of the rubbers. look for leaks in the line wile you under there.

May 13, 2013 | 2000 Toyota ECHO

1 Answer

Noise in front end 2002 zr2 blazer


Two things maybe your problem:1 .Front axle actuator to engage 4wd is not releasing. 2. Front axle u-joint needs replacing. Lift car on jacks with front end off ground. Then spin tires by hand as fast as you can and see if you hear the noise and where it is coming from ( spin in both directions).

Feb 04, 2010 | 2002 GMC Sonoma Extended Cab

1 Answer

Jeep wranger, clanging from front end when turning


Probably the CV joints just behind the brakes on each wheel. Try jacking the car up so that the wheel on that side is clear of the ground, grasp the wheel and rotate it back and forth. Do you get that noise? The joints are not repairable, just replace both sides.

Jul 16, 2009 | 2005 Peugeot 405

1 Answer

Roaring noise front end


it sounds like a bad hub bearing

try raising the front end off of the ground and spin the tires by hand and feel for roughness in the hubs

Jun 16, 2009 | Honda del Sol Cars & Trucks

1 Answer

A noise coming from front end of my saturn is it my tie rods


The noise you hear could be the tie rod ends or several other front end items. Can you jack up the front end? If so then turn the wheels from side to side with your hands griping the wheel at the 9 and 3 oclock positions. if you feel freeplay or looseness you have to reach arround and place your hand on the outter tie rod end and see if the play is there or the inner tie rod end at the rack. I worked for saturn for a few yaears and we had ALOT of front struts that made a clunking sound over bumps. Don't forget the lower ball joints could be bad also. Check these by placing your hand on the bottom of the wheel and pushing and pulling on the wheel with it off the ground while checking the tie rod ends. Good Luck, Scott

Jan 05, 2009 | 2003 Chevrolet TrailBlazer

1 Answer

Front End noise and vibration


Check the U-joints and axle baerings. But its most likely because the truck is in four wheel drive.

Aug 16, 2008 | 2002 Ford F350 Super Duty DRW Reg. Cab

Not finding what you are looking for?
1995 Jeep Wrangler Logo

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...