Question about Cars & Trucks

1 Answer

Hydrolic fluid thickness - Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 10,875 Answers

Very thin

Posted on Apr 18, 2015


1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3.5, 04 chrysler hydrolic valve lash failer


Was the oil you drained very thick? If so this means someone had knew the big end or small end inside the engine was about worn out (very big job) Hopefully you changed the oil filter for a new one, Check your hydraulic fluid is okay worth draining & new fluid replaced look for Fluid leaking this may be the problem. If this dont work I suggest you ask a good Mechanic to listen & I expect the first problem IE: Big end, or small ends gone the engine needs large repair or look for another engine around scrap yards, sorry for bad news. Best Wishes, Malcolm Campbell.

Jul 03, 2017 | Chrysler 300M Cars & Trucks

1 Answer

Where do you put hydrolic fluid on a fifty's fordson dexta tractor


what hydraulic fluid are you trying to add gearbox of the lifting gear ?? if the lifting gear i think its under the engine cover but its been 40 yrs since i done one

Nov 23, 2011 | Cars & Trucks

1 Answer

Excessive bouncing an sometime haed ride


bleed the hydrolic lines empty buy 2 can of hydrolic fluids from lexus i think one should do it dough but u can buy 2 just in case replace fluids and u should be fine if not you can check ure accumulators or the sensers that can cause a bouncy ride too

Nov 07, 2010 | 2003 Lexus LX 470

2 Answers

I have an Audi 2.6 E Cabriolet. The dash shows a flashing red light for the brakes, which according to the manual means low fluid level. Level is ok and the float switch also checks out ok. Solutions...


I had the same problem but weirdly enough I topped up my Hydrolic fluid and it suddenly stop flashing Perhaps it is a short circuit on my Audi 2.6 E Cabriolet or it actually picks up both brake fluid and Hydrolic fluid with the same light

Jan 20, 2010 | 1996 Audi A4

1 Answer

2004 passat 4motion wagon is it a clutch cable or hydrolic? we do not have the owner manual The car starts but you can not put it into gear. It feels like the hydrolics are gone. I can not find where the...


It is hydraulic and uses the brake fluid.Follow the line to the gearbox from brake fluid bottle to just under oil filter and there is a small cylinder that can break its seals and stop the clutch working and its easy to replace

Dec 26, 2009 | 2004 Volkswagen Passat

1 Answer

I have a 2003 4x4 Durango a red fluid is leaking from the top of the rear axel bell housing, the ABS light is on, I know the ABS operates off of hydrolic oil, a line runs across the top of the axel, would...


a red fluid is most likly trans fluid. the abs has nothing to do with that, the abs light could just be a faulty sensor, besides, brake fluid is clear or brakish. now, check to see where the leak is coming from. what i dont understand is brakelines run over the rear diff on most vehicles. see if the leak is coming from somewhere else.

my reconmendation is to take engine brite, which can be bought at any autoparts store, spray area of suspected leak, then rinse with a hose or powerwasher. wait for it to dry and see if the leak becomes more clear, how thick would you estimate the lines to be? 1/4 inch?? 1/8 inch. clean it and find out where the leak is coming from

Jun 22, 2009 | 2003 Dodge Durango

1 Answer

Hydrolic clutch makes grinding noise when in nutural...


It's the throw out bearing. They probably call it a Clutch Release Bearing.

Envision a round large thick tube. On this tube put a bearing at the end of it. Now put a thick metal doughnut on that bearing. The thick metal tube stays stationary, and the metal doughnut spins.
The bearing this 'metal doughnut is riding on, is bad.

Solution? Have this throw-out bearing replaced.
(Clutch Release Bearing)

Apr 25, 2009 | Nissan 300ZX Cars & Trucks

1 Answer

Convertable roof Hydrolic Fluid. What type???


Problem solved via fixya,works like new may thanks.

Mar 27, 2009 | 1984 Pontiac Firebird

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...