Question about Cars & Trucks

1 Answer

My windows don't work I have the center switch off now what

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Cars & Trucks Master
  • 880 Answers

With the driver's door ajar . apply one or two windows to move with the switch and observe the dome light . does it dim slightly as you apply the switch. then you have power to the switch. if not look to the relays or fuses

Posted on Apr 18, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power windows don't work


the master window lock switch is stuck on the off possition test for power in and out, remove and replace

Jan 07, 2013 | 2009 Kia Spectra

1 Answer

Rear left window not working


You have a defective power window motor and regulator assembly. The regulator is pop riveted in so you must drive out the rivet center and then using a special rivet cutter bit cut the head off the rivets. You can use machine screws to put the new regulator in as long as they are short and don't interfere with the operation of the new regulator. I do not show the rear window regulator as being available in the aftermarket, you may have to buy it from Ford.

Jun 22, 2012 | 2000 Lincoln Continental

1 Answer

Where one of my wires on my dash goes to


You will need the wring diagrams for the car. But unless something doesn't work then don't worry about it, there are lots of wires and connectors that go nowhere. These are for accessories that where available but not ordered.

May 31, 2012 | 2001 Chrysler PT Cruiser

1 Answer

Center console park and drive lights replacement


did you check the dash light dimmer ! if yes the switch may be bad. check for a loose wire to dimmer switch also. good-day !

Dec 17, 2011 | Toyota Corolla Cars & Trucks

1 Answer

High Beam headlights don't work, Taillights don't work, Brake lights don't work, Cruise control doesn't work.


Hi Harlan.

I see that you mentioned a 1999 Dodge Grand Caravan in your other question. I assume this question is about the same vehicle.

The checkup will start from the fuse and relay in the power distribution center. A way to test the relays is swapping two relays of the same kind to check if that makes any difference.
If relay and fuse are OK check the wiring to power distribution center, check the dimmer switch and the connection to BCM (the module under the dash).

I have uploaded relay map and wiring diagram at this link. Please click on the link. If necessary click on the picture again to enlarge.

Regards.

Nov 22, 2011 | Cars & Trucks

2 Answers

The window switch on the drivers door to raise and lower the rear passenger is not working. I was able to lower the window but now it is stuck in the down position. Is there a way to override and roll up...



  • So if I understand you correct the drivers door switch is not working for the rear window.
  • Try using the the switch on the rear door for that window then.
  • The master switch is great to work all windows but the rear window switch should still work as well even if the master switch on the drivers door fails.
  • Now if both switches should don't work then it may not be a switch failure at all. this could be a wiring issue or a burnt window motor/regulator.
  • In this case you will nee some help as you are going to "help" the regulator out. Once you get it up I advise to let it be until repaired. You don't want to stress the track up to much before the whole assembly is replaced (should this be the problem).
  • So if both switches don't respond the your going to grab the window (one hand on each side of the window) as if your palms are touching and pull up at the same time the switched is being pushed up.
  • It may take a bit to get it but it will be fine.
  • If the window is down in the door (in the way down position) then get your fingers in there and grab the window and slowly pull up on it. Make sure the switch is being pushed to roll the window up at the same time.
  • Once you get it up a bit then take it the rest of the way as explained above.
  • I have had to do this on a few occasions and it works fine.

  • Hope this helps and thank you for using FixYa.

Regards, Tony

Jul 13, 2011 | 2005 Scion xB

2 Answers

All controls through the drivers side front control dont work. How can I get the window closed ?


If NONE of the windows work, you will have to scan your Body Control Module (BCM) for fault codes to determine what is causing the problem because your windows are controlled by the BCM.

If the driver's window works, but the others don't, check your window "lockout" switch on the drivers master switch to make sure you don't have the other windows locked out. Simply push the switch and try your windows again. If this does not work to get them working, then you will have to scan your BCM as above.

Jun 14, 2011 | 2008 Dodge Grand Caravan

1 Answer

Brake lights don t work turn works lights work brake light does not eover window works


First check the 25 amp fuse in the engine compartment fuse box. If that fuse is OK, contine troubleshooting below.

If the center brake light is working, check the 15 amp brake fuse in the cabin. If the center brake light is not working, the problem is probably the brake switch above the pedal. Take the connector off the pedal and use a big paper clip to connect the 2 terminals in the connector. If this turns the lights on, replace the switch. Let me know if you have questions.

f7bf79f.gif

Oct 27, 2010 | 2000 Chevrolet Blazer

2 Answers

In my rear tailights, the breaklight component is not functioning. i replaced them with brand new lights. the center breaklight located in the back window is still working. Cant figure out why they wont...


Have had this problem many time's here at my shop, if center brake light come's on which you said it does, fuse and relay are good, the problem is your turn signal switch cause the brake light circuit goes through the switch, the switch is bad even though the turn signal's still work's, good luck, hope this was evrey helpful.

May 17, 2010 | 1997 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...