Question about 2007 Volvo C70 2.0T

1 Answer

How do you install the hood lift strut? - 2007 Volvo C70 2.0T

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Volvo Master
  • 1,326 Answers

different car same steps

Posted on Apr 18, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Hood does not stay up when lifted also cigarette lighter is not working 2002 c230

replace the gas struts for the hood
replace the fuse for the lighter

Jun 23, 2017 | Cars & Trucks

1 Answer

How do i replace struts on 2006 dodge daytona

Dodge didn't make a Daytona in 06 but any of the other lines you would unbolt 3 on top of strut tower under hood Do Not Touch Bolt In Middle then lift car on jack stands and remove two lower bolts on strut. Be careful working on struts they are under alot of pressure and they can kill you!

Dec 22, 2014 | Dodge Cars & Trucks

1 Answer

How to replace gas lift for back gate

depends on what model you are asking about . some of the rear lifte gate struts are bolted on . just remove the bolts while supporting the real glass or lift gate .And some struts use a little push clip at each end of the strut . these you can use a pick or a small flat blade screw driver to pop out of place . the new struts should have them already installed on them . so they just snap back on . just remeber to support the gate while changing the struts

Mar 06, 2011 | GMC Envoy Cars & Trucks

1 Answer

How to install hood struts

Hi.on each end of the gas strut it has steel clips which you have to remove with a flat screw driver and then pull the strut off, then just push the new ones on

Nov 17, 2009 | 2004 Jeep Grand Cherokee

1 Answer

How do replace the Hood Strut 1996 Ford Taurus

First, buy 2 new struts. Have someone hold the hood up (so it dosn't fall on your head) Doing one side at a time, using a sharp pick, push it under the strut retaining clip, lifting the clip away from the strut ball.(watch your eyes when doing this). You might have to move the hood up to release it from the socket.Do the same for for both ends> Install the new one by pushing it on,moving the hood up or down alittle to snap it back on the ball socket.

Oct 25, 2009 | 1996 Ford Taurus

2 Answers

2005 grand cherokee hood strut won't hold hood up.Brand new . Only has one strut.

Sounds like the new strut is either upside down or defective. When you purchase these make sure you get a hood support not a lift gate. The lift gate ones are for a much lighter rear hatch and will not support a hood.

Oct 13, 2009 | 2005 Jeep Grand Cherokee

1 Answer

Replacement procedures for front struts on chevy venture lx

lift and safely support vehicle (jack stands),remove wheel and tire assemblies, remove strut to knuckle bolts (two bolts and nuts located directly above the brake rotor very tight),then under the hood you will locate the top strut mount nuts and remove them(you may need to remove wiper linkage to do this) when you are ready to remove the last nut have an assistant hold the strut so it doesn't fall take the strut to a machine shop to get the cartridge changed (most napa stores are also machine shops go to napa online to find the one near you)
installation is the reverse of removal some cars require alignment after strut change torque specs are as follows strut to knuckle bolts 90-120 ftlbs upper mount nuts 40-60 ftlbs wheels 100 ftlbs

Sep 23, 2009 | 2003 Chevrolet Venture Passanger

1 Answer

Installing hood struts

take something to hold the hood up and take a flathead screw driver and pull the pins out on the struts for the hood and pull out the little knob and they come off

Mar 20, 2009 | 1998 Ford Explorer

2 Answers

How to change hood struts 1989 Pontiac Trans Am?

you first have to take off the hood (2 bolts on each side where the hood meets the hinge) then take off the hood hinges (3 or 4 bolts on each side on top of fender) and after all that your hood hinges should be off. on each end there will be a metal retainer that holds the strut on the hinge, carefully pry these off with a screwdriver and install new struts, bolt the hinges back on and finally the hood

(have a friend help you lift the hood off)

Mar 11, 2009 | 1989 Pontiac Firebird

Not finding what you are looking for?
2007 Volvo C70 2.0T Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts


Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides