Question about Hyundai Cars & Trucks

1 Answer

2013 Hyundai sonata. broke the turn signal head light switch off. Want to fix . Looks like I have to take the steering wheel off. How difficult is it and is their any videos I can use

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hyundai Master
  • 10,875 Answers

There is a hole in the center of the wheel that you can access it with,unscrew and pull out the broken arm and replace arm only

Posted on Apr 18, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 393 Answers

SOURCE: replacing rear wheel bearings on 1999 hyundai sonata

  1. for drum brakes with sealed hub(all one piece) remove lug nuts and wheel.
  2. spray penetrating oil around studs if there is a big phillips head screw visible remove it with impact driver/if not use big ballpeen hammer ,tap on flat of drum near studs(becareful not to hit them) until drum loosens(your creating a shockwave to loosen rust)
  3. once drum is off there are 4-bolts coming in from behind backing plate, remove them then hub should be able to be removed w/a little persuation from hammer.
with out sealed hub ,
  1. remove wheel
  2. remove dust cap,cotterpin,star washer(if equipped) do not re use cotter pin
  3. remove nut then washer, wiggle brake drum and front bearing will come out.
  4. put nut on shaft tighten 2-3 turns grab drum by sides and pull towards you this should remove drum leaving inner bearing/seal on shaft
  5. to replace reverse procedure making sure to pack new bearings w/grease(take drum and use long punch to remove bearing races, use race/seal installer to install new races
with disk brakes

  1. remove wheel
  2. remove caliper/bracket
  3. remove rotor
  4. remove 4-bolts from behind,tap old hub out
  5. reverse procedure



Posted on Nov 15, 2008

Mike258
  • 1498 Answers

SOURCE: Turn signal,hazard lights switch bad.

Hi fred,

I worked at a salvage yard for a while. During that time I pulled hundreds of airbags. I thought I'd share a few things.

I've provided this as a supplement to erietracks solution, not to replace it. It provides important additional information you need to be aware of when working on or around SIR (Supplemental Individual Restraint) airbag systems. It lists the potential dangers of doing so and the appropriate precautions against accidental premature deployment. Any work done on the steering column should include this.

Precautions for working with and handling airbags: Take these Seriously!!!

  • Alway wear safety glasses.
  • Control the environment - no kids, pets, people horsing around.
  • Disconnect the negative battery terminal. After you are done, make sure no one is inside the vehicle when you reconnect the battery. If your vehicle has an anti-theft system, you'll need to get your activation codes to reset your sound system.
  • Do not use solvents to clean your airbags. They may ignite if accidentally deployed. Use only a damp cloth.
  • Airbags are sensitive to heat in excess of 190 degrees F. Store them accordingly.
  • Airbags are sensitive to impact - handle them carefully
  • Airbags are sensitive to static electricity - ground yourself, Spray the seat and rug with fabric softener (anti-static - ever heard the term 'static cling')
  • Wires for the SIR are bright yellow, the connectors are labeled.
  • In addition to forward mounted sensors, there are also three sensors in the dash.
  • Do not use voltage testers or VOM's on SIR wiring.
  • Do not haphazardly disconnect airbag components
  • Be safe
  • Be aware

Disable the system:
  • Turn the wheel to the straight ahead position
  • Lock the ignition and remove the key
  • Disconnect the negative battery cable. Be advised, this alone will not render the system safe. The diagnostic module (DERM) can retain a charge
  • Remove the airbag fuse (refer to fuse block cover for location)
  • At the bottom of the steering column locate the Airbag connector. (Yellow wire, yellow conduit)
  • You may need to remove the sound insulator panel beneath the instruments to access it
  • Disconnect the plug
The system is now disabled. That does not mean you can let your guard down. It means that you can now continue working around the system with a higher degree of safety. Continue to observe all safety precautions. Airbags should be handled with caution at all times.

Be safe
Mike


Posted on Nov 22, 2008

  • 840 Answers

SOURCE: Reverse lights on 2001 Hyundai sonata not working

check bulbs first/ then you can check fuses usually under dash or in the engine compartment/Please rate my response thank you very much

Posted on Jan 29, 2009

  • 1 Answer

SOURCE: headlights for 2006 hyundai sonata

Answer
1. Remove the dust cover from behind the bulb that needs replacement.
2. Unplug the bulb.
3. Taking note of the bulb orientation, unhook the bulb retaining clip from the tang that holds it in place.
4. Remove the bulb.
5. Install the new bulb in the same orientation and clip in place.
6. Reconnect the electrical connector to the bulb.
7. Reinstall the dust cover.

Alternatively, if the bulb is burned out and you have less than 60,000 miles, you should take the car to the dealer and let them do it for free for you.

Posted on Feb 16, 2009

  • 135 Answers

SOURCE: steering difficult(slow) and a whining noise when turning wheel

The whine is most likely your power steering pump. Check the fluid in the pump. If you are low on power steering fluid you may have a leaking hose or fitting or the seals in the pump may have began leaaking. If you continue to run the auto without power steering fluid you will burn up the power steering pump very quickly.

Posted on Jul 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2013 hyundai santa fe and the interior lights do not come on when opening the door. I cannot find a way to turn them on. A friend has a 2014 and my car does not work the way his does


Can you turn the interior light on manually? My 2009 Hyundai Sonata has two switches on the interior light fixture. One is labeled 'Door', and must be depressed for the light to work with the doors. The other switch is to turn the light on/off manually.

Dec 02, 2016 | 2013 Hyundai Santa Fe

3 Answers

Turning signals dont work insead hazard lights come on


check the relays and circuit breakers in the motors.

Oct 04, 2008 | Hyundai Motor 2004 Sonata

1 Answer

Why won't it start?


Hyundai Sonata Questions - My Hyundai Sonata won't start ...

www.cargurus.com > Questions > Hyundai > Sonata

CarGurusMar 5, 2013 - My Hyundai Sonata won't start, everything comes on when the key is turned but no ... it is in park and until I jiggle the shift until the light does come on it will not start. Was in ... My 2009 Sonata has been "perfect" with no issues.

2009 Hyundai Sonata turns over but will not start ... - CarGurus

www.cargurus.com > Questions > Hyundai > Sonata

CarGurusJun 16, 2013 - 2009 Hyundai Sonata turns over but will not start, sometimes. - 70000 kms.

Car wont start? - Hyundai Forums : Hyundai Forum

www.hyundai-forums.com/nf-2006...sonata/139435-car-wont-start.html

Mar 14, 2012 - 10 posts - ‎4 authors
2009 Hyundai Sonata GLS 2.4L I4 AT - Slate Blue ... If you turn the ignition to on, not start, do you hear a humming coming from the rear? 2010 Not starting. Fuel Pump? Starter?
10 posts
Apr 1, 2012
Car Won't Start - Break Pedal Hard !
10 posts
Mar 4, 2011
2007 Sonata Won't Start
10 posts
Jan 4, 2011
Car Cranks But Will Not Start
10 posts
Jan 16, 2008
More results from www.hyundai-forums.com

Jan 01, 2016 | 2009 Hyundai Sonata

2 Answers

How to reset the oil life light on 2013 Hyundai Sonata


o reset the 2013 Hyundai service interval, please follow these instructions to reset/setup:
1.Start the engine.
2. If a service is due the display will show "Service required".
To reset this message, press the SELECT/RESET button (left
pointing arrow) on the bottom right of the steering wheel for more
than 1 second.
3. The service interval will be reset to the default setting.
*The service interval feature has to be turned on and set by
the user by accessing the SERVICE INTERVAL menu. Press
the MODE button (rectangle icons) on the bottom right of the
steering wheel to highlight the SERVICE INTERVAL menu.
Press the SELECT/RESET button to access the menu and
use the DOWN arrow to turn the SERVICE mode on and
set the applicable interval.
4. Turn the ignition off and then start the engine to verify the
indicator has been reset.
- See more at: http://oilreset.com/2013-hyundai-santa-fe-service-interval-reset/#sthash.MniBNaqR.dpuf

Nov 30, 2014 | 2013 Hyundai Sonata Limited

1 Answer

Bought a new mitsubishi mirage 2013 airbag light is on on dashboard why?


Hi Sandra, Have a diagnostic scan carried out on the vehicle. The usual problem is with the cassette unit mounted behind the steering wheel. Regards John

Jun 07, 2014 | 2007 Hyundai Sonata Limited Sedan

2 Answers

Turn signal


Its attached to the lever, mounted on the side of the steering column.

Jan 10, 2013 | 2000 Hyundai Sonata

1 Answer

Hyundai Sonata 2004 turn signal does not work properly


did you check the directional switch. sounds like you have a bad one

Nov 07, 2012 | Hyundai Sonata Cars & Trucks

1 Answer

Turn signal handle broke off and is hanging by wires


You can buy the turn signal switch at Napa or other auto parts stores. It's a combination switch. Remove the steering wheel and remove the 2 screws that hold the turn signal switch on, unplug the wires and installation is reverse of removal.

Apr 02, 2010 | 1992 Ford F150 SuperCab

1 Answer

Signals not working hazards out all fuses are good


could need to replace the switch used to turn signals, if not that could need to go into steering wheel?

Feb 25, 2009 | 2000 Hyundai Sonata

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...