Question about Cars & Trucks

1 Answer

My van will go into gear however when its in drive it will not move...when you put it in reverse it will move .. have replaced the filter and fluids but it is still happening

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 1,326 Answers

Slipping transmission

Posted on Apr 17, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why won't my windstar move in reverse or move in drive with the engin is running?


check the trans fluid ?can you here the van go into gear or not at all ?

Mar 29, 2015 | 2001 Ford Windstar

2 Answers

My chevrolet transport is no longer engaging gears, when i put it on drive or reverse gear, it doesnt engage


check fluid level in transmission . run the fault codes and look for a faulty TCM or torque converter clutch solenoid / servo

Mar 20, 2014 | 1999 Chevrolet Venture

1 Answer

Can you tell me if a 97 dodge caravan transmission 3.3 will interchange with a 3.8. This is the trouble i have had and have decided to put in Transmission. Driving down the road and van sounded like it...


1. Yes the 3.3 and the 3.8 are the same bolt pattern. But the gear ratio in the differential might be different.

2. Did you replace the filter and put it back together? Does it do the same thing after you changed the filter? If it was an electrical issue with speed sensors or the solenoid pack, reverse would still work.

Jun 09, 2010 | 1997 Dodge Caravan

1 Answer

Driving a 2003 Ford windstar. Went to pass and


Very common on this make and model trans, pump drive splines inside torque converter strip out and pump is not turning, Most times there is no damage to pump shaft. Remove trans and remove torque converter, inspect the splines at the very bottom of the hub hole. If stripped out inspected pump shaft splines which are the smaller center splines coming out of trans, if ok replace torque converter and re-install trans, change out fluid, clean any metal from magnet and replace filter, fill with fluid and verify proper operation.

Mar 01, 2010 | 2003 Ford Windstar

1 Answer

Reverse wont work after a long drive


Change your fluid and filter and see if that helps,and put a can of lucas in it

Jul 28, 2009 | 1991 Honda Accord

1 Answer

Transmission still shifts erractically


well if you have a lot of millage it could only be the gearpump in the transy thats finished,unfotuntly ...you cant really change -it without rebuilding the all transy
other than that you still can drive-it but try letting the gear go on by it self ,you could damage your van by doing that !! you mignt not have choice but if you do ...try not doing-it!

Jul 21, 2009 | 2000 Chrysler Town & Country

1 Answer

Volvo xc70--engine starts but truck doesn't move when put in gear


check tranny fluid.if fluid level is correct.change fluid and filter if its been a long while.if it still wont go into gear.your tranny oil pump is worn.and the forward clutch seals and drive plates worn.

Jun 11, 2009 | 1998 Volvo S70

1 Answer

TRANSMISSION COMES OUT OF DRIVE WHEN I STOP THE CAR


Start with a complete flush of the trany and torque converter, and a filter replace. That should fix the problem, but the Taurus has a bad reputation for trany's going out frequently.

Jun 08, 2009 | 1998 Ford Contour

2 Answers

Transmission


Check your universal joint...might be broken.

Jun 01, 2009 | 2003 Ford Windstar

1 Answer

2000 Dodge Caravan


Hello,
It sounds as if the transmission's clutch plates are excessively worn. You have 2 options;
1. Replace all of the transmission fluid & the filter too. That may fix the problem although not guaranteed to work completely.

2. Do what I ultimately had to do (after trying the 1st thing) and bring it to a Transmission repair shop and have it rebuilt for $1,400 (as good as new). I thought the van was worth it and I could get a lot more miles from it of course you have to determine this for your self and your van's condition.

Good Luck!
Rich Lilja

Nov 10, 2008 | 2000 Dodge Grand Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...