Question about Chrysler Sebring

1 Answer

I have a 2005 Chrysler Sebring tour and the hose that connects to the coolant aor bleeder it breaks

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 22,095 Answers

Obtain a new one its not repairable ,dealer only part iam afraid

Posted on Apr 18, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: I HAVE A 2005 CHRYSLER SEBRING AND DOME LIGHT,RADIO ALL POWER LOCKS HAVE QUIT WORKING

me too! - looking at fuse #5 red 10 Amp one but has black thing on it.

Can't get if off..

Have read the manual is wrong and to use panel on side of fuse box for fuse locations...

Posted on Jun 24, 2009

  • 9 Answers

SOURCE: 2001 chrysler sebring lxi is leaking coolant and seems to have a emissions problem

The coolant leak is probably from the water pump. The seal behind the bearing is worn out. You need a new water pump.

Posted on Jun 29, 2009

  • 1986 Answers

SOURCE: Adjust the headlights on 2005 Sebring, Touring Sedan

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall. Also mark where the center of the bulbs would be (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall. For horizontal, aim the hot spot directly at the line you marked for the center of your bulbs

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Nov 04, 2009

techbuster
  • 5081 Answers

SOURCE: how do you change the battery for a 2005 chrysler serbring

Battery is behind the tire. You have to remove the tire to get to the battery.
First of all you DO NOT have to remove the tire...you turn your wheels hard right, this will give you plenty of room to get to the battery. Remove the wheel well plate and you will see the battery just in from of where the tire would normally be pointing. From there it's pretty straight forward.

Posted on Dec 06, 2009

  • 1757 Answers

SOURCE: I need a timing belt diagram for a 2005 chrysler sebring

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

Again my apologies...
http://www.2carpros.com/car_repair_information/year/2005/make/chrysler/model/sebring/2005_chrysler_sebring_timing_belt_diagram_marks.htm

Posted on Mar 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the bleeder valve at


which one ? brakes? coolant? coolant is on top of the motor next to the radiator hose on the thermostat housing, be carful soak it with penetrating oil for one day so you don't break it. (do not drive while soaking it)

May 08, 2014 | 2001 Chrysler Sebring

1 Answer

2004 2.7 L leaking water around the top of the engine coolant air bleeder


Replace the coolant air bleeder, front and center top of the engine. Remove the 10mm bolts holding the air intake down, prop it a a few inches, take the four bolts out and the two bolts holding the top radiator hose to it, polish ip the top of the motor where the pice sits bolt it back together. It took me about ten minutes to put in the new one. The part from advanced auto was 39 bucks, comes with a new o ring for the top hose, it is a piece of cake.

May 07, 2012 | 2004 Chrysler Sebring

1 Answer

2005 chrysler sebring coolant drain plug location


take the bottom hose off it doesnt have a drain plug

Jan 13, 2011 | 2004 Chrysler Sebring

1 Answer

2005 chrysler sebring malfunction light is on engine stall when cold


Could be a bad battery connection. Your fuel system may be going bad. Might have a faulty coolant temperature or intake air temp sensor. Could even be a MAP sensor. Is your check engine light on?

Jan 10, 2011 | 2005 Chrysler Sebring Conv

1 Answer

Where is the battery on the 2005 Chrysler Sebring Touring Convertible?


Remove the drivers side front tire, in the wheel well liner there's a access plate to get to the battery.

Aug 23, 2010 | 2005 Chrysler Sebring Conv

1 Answer

Fan comes on on my sebring 2004 convertible when ac is on and when I disconnect from coolant air bleeder. Fan doesn't come in during normal run


You need to replace the coolant sensor,and bleed all the air out of the coolant system.The coolant sensor does not sense air,or hot moster,only pure solid coolant,or water.

Oct 09, 2009 | 1998 Chrysler Sebring

1 Answer

2001 chrysler sebring lxi is leaking coolant and seems to have a emissions problem


The coolant leak is probably from the water pump. The seal behind the bearing is worn out. You need a new water pump.

May 31, 2009 | 2001 Chrysler Sebring

1 Answer

Termostat how to repair


one rad hose goes to the water pump the other goes to the thermostat on top of the motor. undo the hose clamp and take off the hose that goes to the thermo . DO THIS WHEN THE VEHICLE IS COLD. have a small container handy to catch any coolant that may leak out. be sure to keep the hose up so coolant doesnt leak all over the ground.Once you take off the hose the thermostat should be right there. 2 bolts to take it out. fairly simple actually. replace with the new one and put hose back on. replace any coolant that might have leaked into your container. Hope this helps you Crystal. let me know. Thanks, Mark.

Sep 21, 2008 | 1996 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...