Question about 2000 Ford Taurus

2 Answers

I am trying to find out what is making my front end grind on passenger side when i drive down the road on 2000 ford taurus

We just changed the lower ball jint and wheel bearing assembly and it is grinding yet

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Ford Master
  • 454 Answers

May also be a hub or wheel bearing getting ready to go bad.

Posted on Apr 23, 2015

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

Check the front brake rotor. When the brake pads wear down too far they will make a grinding noise. I am not sure what sound the axle makes when they begin to wear out. I would check the boot that covers the axle joint for any damage.

Posted on Apr 18, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How can i tell if the ball joints are bad on a


you have to jack up the lower control arm out by the wheel then using a bar pry up on the wheel there should be very little if any play then grab the top and bottom of the wheel and try to move the wheel back and forth there should be no movement at all. the up and down movement is measured in thousands of an inch.

Oct 05, 2014 | 2002 Ford Taurus

1 Answer

Metal on metal sound from front end


May Sound stupid but I would check for gravel.

Feb 18, 2014 | 2000 Chevrolet Cavalier

1 Answer

97 4x4 sonoma When driving, I can feel grinding


replace wheel bearings or check for feathering of tires

Sep 09, 2013 | GMC Cars & Trucks

1 Answer

What makes my 2002 Pontiac Firebird grind when driving and/or turning?


Sounds like a wheel bearing. Jack up front end and spin wheels by hand and listen for grind. Same for rear wheels. Make sure brake linings are good all around. Do the swerve test. Drive down road bout 40mph and swerve moderately one side to other. If noise gets louder with weight shifted to one side more than other its most likely a wheel bearing.

Apr 05, 2012 | 2002 Pontiac Firebird

1 Answer

Hello, I just purchased a used 97 Dodge Caravan Se and when I was driving it down the road it started to shake and make a grinding noise in the front end. Does anyone have an idea of what this could be?...


Sounds like your front passenger's side wheel bearing might be going bad. It could also be the cv axle is going bad. Have it looked at before it gets worse and possibly seizes up on you.

Aug 23, 2011 | 1997 Dodge Caravan

1 Answer

Front wheel bearings replacment in a 2003 ford taurus


since this is a front wheel drive car i wouldnt really advise doing this by yourself unless youv done stuff like that before. I would say its not so much difficult as it is tedious work and requires some time to complete.

Oct 07, 2009 | 2003 Ford Taurus

1 Answer

2002 ford taurus shakes


You need to have the front end inspected for damaged steering components. Check your Tie Rod ends, A frame bushings and ball joints to make sure there isn't excessive wear or lose connections. If all of that is in good working order Drive down the road with a friend in the next lane over and have them look to see if either wheel in bouncing. If either wheel is bouncing you need to replace the struts. they are replaced in pairs, both sides. The front end will need to be aligned after you do this.

Aug 27, 2009 | 2002 Ford Taurus

1 Answer

2001 Tarus clunking sound


very common problem is the sway bay end links that attach to the strut from the sway bar. They sound like a light chuckling knock over bumps. The bushings that hold the subframe up wear or the bolts loosed due to the bushings wearing. usually the rear ones The bushings are 2 piece ,upper and lower Tighten with 18mm socket

Feb 17, 2009 | 2000 Ford Taurus

1 Answer

2001 Ford Taurus rear end bounces/slips off to side slightly


This is most likly a low RR tire. Check the tire pressure first. If that is OK, I would slowly drive to somone qualified to examine the rear suspention to see what might have broken.
good luck

Feb 07, 2009 | 1991 Ford Taurus

1 Answer

Will a 1990"s model ford taurus front end axel inter change with a ford taurus 1988. Oh that's driver and passenger side axels.


it should as long as everything is the same. you could call your local parts store just to make sure and they will tell you

Nov 30, 2008 | Ford Taurus Cars & Trucks

Not finding what you are looking for?
2000 Ford Taurus Logo

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...