Question about 2006 Chevrolet Cobalt

1 Answer

2006 chevrolet cobalt engine codes p0410, p2430, p2440 how do cate the secondary air injection valve and how do I fix it?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 11,486 Answers

Posted on Apr 17, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: my 2005 chevy trail blazer has code p0410 and i

check the air pump on your trailblazer, make sure its clean inside and the hoses are properly fastened. also check to make sure it works properly by listening for it when you start the vehicle. if the air pump is working correctly, replace the position 1 o2 sensor meaning the sensor on the exhaust manifold. the air pump is located under the vehicle, inside the frame rail on the drivers side in front of the transfer case crossmember with 2 hoses connected to it.

Posted on Feb 21, 2009

  • 184 Answers

SOURCE: code P0410 sonoma 03 2.2 how can i fix??

These two links have the answer:
http://www.obd-codes.com/p0410
http://www.obd-codes.com/forums/viewtopic.php?f=1&t=1956

Good luck!

Posted on Mar 31, 2009

Molson02536
  • 3854 Answers

SOURCE: engine code p0410

If the air pump is working then it's going to be the one way check valve at the manifold. It's common for the check valves to go bad before the air pump, check the pipe from the pipe to the manifold too.
Before you get that far i believe there was a TSB and the warranty is 5 years to the emission system on vehicles. Looks like your close to the end of your 5 year so step on it to the dealer while you can still get a deal on this repair.
Good luck and hope this helps.

Posted on May 27, 2009

  • 272 Answers

SOURCE: mazda rx8 fault code p0410

The P0410 code refers to the (secondary air system) emissions system. The AIR pump puts air to the exhaust to lower emissions. It takes in outside air and pumps it through two one-way check valves into each bank of the exhaust.
.
About 90% of the time that this code is set, the one-way check valves have worn out or failed and allow water (which occurs naturally in the exhaust) back into the pump. In any cold climate, especially in climates with higher humidity, this water may be more excessive. The water partially fills the AIR pump, it can then freeze. When the PCM commands the pump on, if the pump is frozen it cannot turn, thus overloading the circuit and "popping" the fuse.

A code P0410 may mean that one or more of the following has happened:

  • Water may have collected in the AIR pump or the vent solenoid and frozen or corroded the pump
  • Blown AIR pump fuse due to freezing up
Possible solution:
This may be covered under the emissions warranty on the vehicle. If your vehicle is out of bumper-to-bumper warranty, check if the emissions warranty is still valid!
  • Replace the AIR pump AND one-way check valve
  • Test and clean the AIR pump AND test and replace the one-way air check valve
  • Replace the AIR pump inlet hose
  • Replace the AIR pump fuse (found under the hood)
It is really only an emissions issue and won't harm your car's engine ot drivetrain. It will however mean you won't pass emission testing if you live somewhere that tests for that like I do!

Posted on Jun 03, 2009

emissionwiz
  • 75822 Answers

SOURCE: Chevy S-10, 2001,4cylinder,service engine soon light

I am very familiar with this code, there is a GM service bulletin about this problem, in short it says to replace the secondary air injection electric pump assmebly

Posted on Jul 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2008 Trailblazer has OBD-II code P2430. How do I replace the secondary air injection pump?


This code doesn't mean to replace the air pump ,
DTC P2430 : Secondary Air Injection (AIR) System Pressure Sensor Circuit
Circuit/System Description
The secondary air injection (AIR) system aids in the reduction of hydrocarbon emissions during a cold start. The system forces fresh filtered air into the exhaust stream in order to accelerate the catalyst operation. An electric air pump, the secondary AIR injection pump, provides filtered air on demand to the AIR control solenoid valve/pressure sensor assembly. The AIR control solenoid valve/pressure sensor assembly controls the flow of air from the AIR pump to the exhaust manifold. The AIR solenoid relay supplies the current needed to operate the AIR control solenoid valve/pressure sensor assembly. A pressure sensor is used to monitor the air flow from the AIR pump. The engine control module (ECM) supplies the internal pressure sensor with a 5-volt reference, an electrical ground, and a signal circuit.
This is a pressure sensor problem . What this video on testing !
Chevrolet Malibu P2432 Secondary Air Injection System

May 11, 2017 | Cars & Trucks

1 Answer

Find the sensor code P2430


DTC P2430 : Secondary Air Injection (AIR) System Pressure Sensor Circuit
Circuit/System Description
The secondary air injection (AIR) system aids in the reduction of hydrocarbon emissions during a cold start. The system forces fresh filtered air into the exhaust stream in order to accelerate the catalyst operation. An electric air pump, the secondary AIR injection pump, provides filtered air on demand to the AIR control solenoid valve/pressure sensor assembly. The AIR control solenoid valve/pressure sensor assembly controls the flow of air from the AIR pump to the exhaust manifold. The AIR solenoid relay supplies the current needed to operate the AIR control solenoid valve/pressure sensor assembly. A pressure sensor is used to monitor the air flow from the AIR pump. The engine control module (ECM) supplies the internal pressure sensor with a 5-volt reference, an electrical ground, and a signal circuit.

Sep 14, 2015 | 2008 Chevrolet Chevrolet Cobalt LT

1 Answer

I have a service engine soon light on and have hooked up an OBD11 reader to it and got code P0410 pertaining to a secondary air injection problem. hoses are fine, pump is new.


P0410 Oldsmobile - Secondary Air Injection System Malfunction

Possible causes: - Faulty Vacuum hoses damaged
- Faulty Air Pump inoperative
- Air bypass solenoid harness is open or shorted
- Air bypass solenoid circuit poor electrical connection
- Air bypass solenoid leaking/blocked or stuck open/closed
- Air diverter valve leaking/blocked or stuck open/closed

Tech notes: Visually inspect AIR pump and AIR bypass valve harness and connector, if connector are OK, then replaced AIR bypass valve.

When is the code detected? The secondary air injection system does not detect the presence of air in the exhaust when introduced by the secondary air injection system.

Possible symptoms: - Engine Light ON (or Service Engine Soon Warning Light)
- Engine hesitation

P0410 Oldsmobile Description An air pump is used on the vehicle to lower tail pipe emissions on start-up. The Powertrain Control Module (PCM) grounds the Air pump relay control circuit which energizes the Air pump. The PCM also grounds the Air combination valve vacuum control solenoid circuit, which energizes the Air vacuum control solenoid. Vacuum is then applied to both Air combination valve diaphragms which opens the shut off valves. The PCM enables both circuits simultaneously when Air system operations id desired. When the AIR system is active, then Air pump forces fresh air into the exhaust stream in order to accelerate catalyst operation. The AIR combination valves replace the conventional check valves. When the AIR system is inactive the shut off valves prevent air flow in either direction.
P0410 Oldsmobile Secondary Air Injection System Malfunction

May 30, 2015 | 2001 Oldsmobile Intrigue

1 Answer

Check engine light on with code p2440


That code is related to the Secondary Air Injection System (SAIS) switching valve being stuck open. This valve is located on the passenger side of the engine mid position.

Feb 01, 2014 | 2008 Chevrolet TrailBlazer LT

1 Answer

P0410 code 01 02


P0410 - Secondary Air Injection System Malfunction
Possible causes- Faulty Vacuum hoses damaged
- Faulty Air Pump inoperative
- Air bypass solenoid harness is open or shorted
- Air bypass solenoid circuit poor electrical connection
- Air bypass solenoid leaking/blocked or stuck open/closed
- Air diverter valve leaking/blocked or stuck open/closed

Read more: http://engine-codes.com/p0410.html#ixzz24VOZPAy2

Aug 24, 2012 | 2000 Chevrolet S-10

1 Answer

How to clean secondary air injection incorrect upstream flow detected Code PO411


The valve may need to be replaced. Only air flows thru the components.

Jul 03, 2012 | 2008 Chevrolet TrailBlazer LT

2 Answers

Grand Prix pontiac error code p0411 and p2440


P2440 refers to the Secondary Air Injection system. It means that the switching valve is stuck open. We already replaced the secondary air flow pump, now it's telling us that's its the secondary air flow sensor and the valve is stuck open. the code is coming up P2440

Oct 15, 2011 | 2006 Pontiac Grand Prix

1 Answer

How to fix P2430 code on a 2006 Pontiac Grand Prix


P2430 Secondary Air Injection System Air Flow/Pressure Sensor Circuit,
The AIR diagnostic uses 3 phases to test the AIR system:

DTCs P0411 and P2430 run during Phase 1
DTCs P2430 and P2440 run during Phase 2
DTC P2444 runs during Phase 3
During phase 2, only the AIR pump is activated. The solenoid valve is closed, this is p2430 and p2440. -The AIR system pressure sensor is stuck. good-day !!

Jul 15, 2011 | 2006 Pontiac Grand Prix

1 Answer

What does engine code p2440 indicate?


P2440 Secondary Air Injection System Switching Valve Stuck Open Bank1

Problem is usually the air switching valve that operates the air line coming from air intake to air pump, clean it or replace it.

Here a bulletin.

Aug 11, 2010 | 2007 Chevrolet Cobalt Coupe

Not finding what you are looking for?
2006 Chevrolet Cobalt Logo

357 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...