Question about Ford Ranger

1 Answer

Why is the high pressure hose leaking at the pump?

Changed O ring, still leaking not as bad but also a lot of play in that line. Fitting is tight as can be.

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Ford Expert
  • 496 Answers

Time to change the Hose and it that does not fix it then you will need to replace the Pump.

Posted on May 14, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
keemo68
  • 1263 Answers

SOURCE: 1999 Mercury Cougar powersteering hose leak

if that is the case the fitting is probably cracked and unless you replace that fitting it will continue to leak.

Posted on Aug 30, 2008

  • 69 Answers

SOURCE: power steering line leak for 93' taurus lx at pump

did the hose get cracked or crimped when it was replaced may need new hose

Posted on Oct 06, 2008

  • 110 Answers

SOURCE: leaking brake line

u can use metal pipe sections but not recommended may b cheaper to replace whole pipe certainly a lot easier t fit

Posted on Nov 21, 2008

txkjun
  • 409 Answers

SOURCE: 1996 Lexus LS 400 high pressure hose replaced

The leak could be in the steering rack.

Posted on Feb 15, 2009

autotherapis
  • 501 Answers

SOURCE: I have a 1999 taurus 3.0 v6. The trans cooler line

You can buy a snap in replacement end that can be bent and attached to 3/8 th's fuel line and by pass the rotted metal line. I have been doing transmissions Since 1981, and have the same rotted lines on my 01 Windstar. I just went to all hose except the line into trans and into radiator. double clamp the hose on the lines and save a lot of money. make sure you sip tie the hose so it is out of the way and check your trans fuel level when you are done. Let it get hot in park and running when you check the level on the stick.

Hope this helps.

Hope this helps

Posted on Aug 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change powerstering pump chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Dec 13, 2012 | 2008 Chevrolet Uplander

2 Answers

Replace power steering pump on 06 chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Jul 08, 2012 | 2006 Chevrolet Uplander

1 Answer

2000 impala red circle recessed in radiator is leaking replace repair? ect...


It seems that the "black bolt" is the bolt-shaped sheet metal around the fitting for your trans cooler line. If you are certain that your connection is good and the leak is coming from around that fitting then you will have to replace your radiator as the area around the fitting is probably cracked. Take a good close-up look, with an inspection mirror and a light, to try to determine from where the fluid is leaking.
Does your other line have an O-ring?

Nov 28, 2011 | 2000 Chevrolet Impala

1 Answer

I have a 2001 Taurus with the 24 valve engine. The high pressure line to the p/s pump blew a leak and my steering started to moan so I limped it home and replaced the p/s pump to be safe. I then replaced...


Your story is very strange to me

You work on your own car which is
great,even playing with a teflon gasket
trying to learn something & resolve a
problem

THEN -- you go off somewhere & talk about
a dealer & a $500 hose

WHY would a dealer even come to mind,
after the 3 year warrantee is up?

Wouldn't you buy the hose, if necessary
& replace it yourself?

Remove the fluid resevoir & check that the
internal filter isn't clogged.
That may have been your only problem

Jun 22, 2011 | 2001 Ford Taurus

1 Answer

The new power steering pump that I put on a 2001 dodge durango is leaking at the high pressure fitting it is tight.


The pressure hose is leaking due to forgetting to install the o-ring. You should disconnect pressure hose install o-ring then tighten!

Jun 12, 2011 | 2000 Dodge Durango

1 Answer

2000 dakota sport leaks power steering fluid where high pressure line connects to pump. i have replaced the o ring and it slowed it down but did not stop it. I have replaced the o ring twice. What next?


Try some teflon tape on threaded end of hose where o ring went. Also look closely at compression fitting where hose and metal crimp meets, they can leak there. Have seen that on occasion.

Jan 07, 2011 | 1988 Dodge D-Series Pickups

1 Answer

Leak in power steering, not sure if bad lines or pump. how to determine where problem is


You'll need to look at the lines from under the passenger side of the car. Often, it's a high pressure line. They have compressed fitting on the hoses that often leak, due to the high pressure.

May 26, 2010 | 2002 Kia Sedona

1 Answer

Subaru impreza 1993 power steering leak


YOU CANT USE A REGULAR FUEL LINE ON POWER STEERING AS A HIGH PRESSURE HOSE.BECAUSE POWER STEERING PRESSURE IS 1000 PSI.YOU HAVE TO BUY THE POWER STEERING HIGH PRESSURE HOSE IT HAS NUMBER OF PLIES MATERIAL WEAVES TO MAKE IT STRONG.IT WAS MADE FOR POWER STEERING HIGH PRESSURE.YOU DONT HAVE A BLOCKAGE .THE HIGH PRESSURE HOSE JUST WORE OUT.REPLACE IT .IT SHOULD FIX THE PROBLEM.

Sep 04, 2009 | 1993 Subaru Impreza

1 Answer

Replace power steering pressure hose


If the high pressure hose going to the power steering pump is leaking and needs replaced. You will need two wrenches to do the job. One to hold the backing nut and one to turn out the fittings. This is a pretty simple job, although space is usually tight, especially where it attaches to the pump. The fittings are usually stubborn to remove, so I cut the line so that I could get a socket on the fitting nuts and got them broken loose much easier. Hope this helps and good luck.

Jul 07, 2009 | 2004 Pontiac Grand Prix

1 Answer

Power steering line leak for 93' taurus lx at pump


did the hose get cracked or crimped when it was replaced may need new hose

Oct 06, 2008 | 1993 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...