Question about Ford Ranger

2 Answers

Ford ranger ute 2009 mechanic said timing belt gone would there be any of belt left behind in the motor or do they just fall off

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 503 Answers

If the belt is Broken the valves are also damaged it will be a major job and expensive to correct.

Posted on Apr 17, 2015

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 154 Answers

Your question of "Would there be any of the belt left behind?"
The timing belts usually strip/break off the teeth. The belt pieces do not enter the inside of the engine.
However if the engine is an interference engine - then chances of valves being hit and damaged by the pistons because of improper cam to crank timing is highly likely.
Does that answer your questions?

Posted on Apr 17, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 99 ford ranger timing belt


Using the same 13mm socket, remove the bolt that you found under the a/c compressor. Look down and to the right of the bolt that you just removed, and you will see two more bolts. Both are 13mm. Easiest way that I found was to go under the driver side tire well, and use 3/8 extensions to reach the two bolts. Once removed, the bracket and the power steering pump should be moved to the driver's side of the frame, and the a/c placed on top of the p/s assy.




Remove the bolts (6mm) that hold the timing belt cover in place. Gently work your way around the cover, and push the tabs in to remove the cover.


Use an impact wrench and 7/8 SAE socket to remove the crankshaft pulley. A SOCKET WRENCH WILL NOT WORK. Once removed, gently tap the pulley with a 2x4 (yes the wooden board) to remove. If you have a gear puller, use that. I don't own one.




Remove the old belt. Now for the alignment. Crank - sprocket on bottom. Use the bolt you removed, and a ½ drive wrench, with the 7/8 socket to turn the crank. Once the keyway is at high noon, leave it alone. Next, move the oil pulley sprocket until the diamonds are aligned. This should put the oil pulley at high noon, also. The camshaft should have a diamond and a triangle. The diamond should go to high noon, and the triangle should align with a triangle on the plastic behind the sprocket. YOU SHOULD REALLY CONSIDER CLEANING THE ENTIRE AREA BEFORE ALIGNING THE SPROCKETS. You cannot align the camshaft without locating the two index (triangle and diamond) marks.


You will also notice a tensioner for the timing belt. You will need to loosen the tentioner with a 13mm and 17mm wrenches. Loosen, then use a cheeter bar bar to move the tentioner over. Lock in place by tightening the tentioner bolts. Place the belt on the crankshaft, move to the oil pulley, then to the cam pulley. Release tentioner, then check the alignment. If correct, reverse the above removal plan, and you should be good.




Don't buy the Haynes manual. I fought with the instructions for this project, and the picture for the timing belt project doesn't show the two indexes for the cam sprocket.



Also, while you are doing this, you should replace the antifreeze if you haven't in the past two years.



Best of luck.

Posted on Jul 13, 2008

  • 899 Answers

SOURCE: 1991 ford ranger not getting any spark

probably the coil , but have your alternator checked first

Posted on Oct 07, 2008

  • 1 Answer

SOURCE: 1988 ford ranger

the timing setting is 6 degrees before top dead center

Posted on May 21, 2009

  • 33 Answers

SOURCE: removal and install timing belt 1994 ford ranger/

Depends on the engine.

Posted on Oct 10, 2009

  • 1757 Answers

SOURCE: what do the timing belt marks line up on a 94 ford

My apologies for the delayed response. I am going back to answer unanswered questions.
CLICK
on the following LINK. It has the Timing Belt & Mark(s) Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my sincerest apologies...
Thanks!

http://www.2carpros.com/car_repair_information/year/1994/make/ford/model/ranger/1994_ford_ranger_timing_belt_diagram_marks.htm

Posted on Mar 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My cam belt has gone on ford ranger thunder 2008 2.5 diesel is it a non interference engine


THE 2.5 IS A NON-INTERFERANCE ENGINE. Replace the belt, the water pump and all t-belt idlers and tensioner pulley

Jun 20, 2016 | 2008 Ford Ranger 2WD

1 Answer

G'day got a 2009 ford ranger xlt diesal ute ran out of diesal what do these need bleeding or will it eventually start


Sometimes there is a bleed bulb/ pump near the injectors on some Diesel engines.this should be easy to see from the engine bay otherwise you will need to keep turning it over to force fuel up the line.

Feb 05, 2015 | Ford Cars & Trucks

2 Answers

Where is the cam shaft senser on a ford ranger 2.5 td 2002


Ford did not put a 2.5 in a Ranger, maybe a 2.3 ?
2.3 = 2007-01-27_154722_2.gif
3.0 - The CMP sensor& synchronizer/shaft are located behind the intake manifold (i.e., back near the firewall on a Ranger) on the top of the cylinder block. If you just need to replace the sensor, it is a simple job of unplugging the electrical connector and removing the screws holding the sensor in place. Here is a sketch of the sensor to give you an idea what to look for:

Jun 17, 2014 | 2002 Ford Ranger Regular Cab

1 Answer

Heater blowing cold air


1. Check coolant level to ensure full, and thus getting to heater core.
2. If that didnt work, With engine hot and running, and heat on in the truck, feel heater core inlet and outlet hoses at the engine compartment firewall to ensure both are hot an thus getting flow. If not the core is clogged or there is a faulty valve in the flow path.
3. If te hoses are hot there is flow thru the core and either your blend door is broken and shut or the blend door motor or circuitry is bad.
4. You tube Ford Ranger blend door for video on how to access behind the glove box. You can fairly easily remove the motor and undoing so check its operation and also the blend door operation.
Likely your motor has gone bad and can be replaced using a low profile socket wrench to remove the 3 Screws holding it in place. I bought a new motor for $40 at One o te auto parts chains locally.
Good luck!

Jan 30, 2014 | 2009 Ford Ranger Regular

2 Answers

Where is timing belt located on 2004 ford ranger 4 cylinder


Behind the water pump pulley and the timing belt cover.

Dec 12, 2012 | 2004 Ford Ranger

2 Answers

1985 Ford ranger died and will not start....getting gas..have fire to the distrubutor, will turn over but not start.


You have fire to the Distributor, but do you have fire at the plugs? The 4 cylinders had an external timing belt behind a shroud. Look to see if you broke a timing belt. Or you could have a bad stator or module in the Distributor.

Feb 24, 2011 | 1985 Ford Ranger

1 Answer

How to replace timming belt on a 1986 ford ranger 2.0 four cyd two wheel drive


ahh the two liter iron duke i had that same truck once great engine although they have a bad reputation for timing issues the timing belt is located behind the harmonic balancer/crankshaft pulley once the fan and crank pulley are removed you should have complete access to the timing cover. open it and its as simple as lining up the confusing timing marks on the crank and cam when you put the belt on and apply tension with the belt tensioner pulley.hope this helps

Dec 22, 2010 | 1986 Ford Ranger 2WD

1 Answer

I need wire color codes for a 2009 Ford ranger basic radio. Installing an aftermarket stereo.


I took my time to find this for u please show your thanks with a "FIXYA" rating.

2009 Ford Ranger Car Stereo Installation Guide
Car Radio Battery Constant 12v+ Wire: Violet/Red
Car Radio Accessory Switched 12v+ Wire: White/Red
Car Radio Ground Wire: Black/Yellow
Car Radio Illumination Wire: Blue/White
Car Stereo Dimmer Wire: Green/Red
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): White
Left Front Speaker Negative Wire (-): White/Brown
Right Front Speaker Positive Wire (+): White/Violet
Right Front Speaker Negative Wire (-): White/Orange
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): White/Orange
Left Rear Speaker Negative Wire (-): Brown/Yellow
Right Rear Speaker Positive Wire (+): Brown/White
Right Rear Speaker Negative Wire (-): Brown/Blue

Sep 30, 2009 | 2008 Ford Ranger 2WD

2 Answers

Ford ranger 1997 2.3 engine problem


Sounds like the idle bypass valve is nfg. Try checking engine codes first. Try this link, you'll find it helpful. http://autorepair.about.com/od/troubleshooting/a/OBD_codes.htm . If you need to know how to check the codes, ask back here, I'll explain. Hope this helps.

Jan 03, 2009 | 1997 Ford Ranger SuperCab

2 Answers

Ford R2 diesel timing belt installation


i am curious... what year is this van... and what diesel engine does it have. i am a professional diesel mechanic that specializes on ford engines and i never herd of an R2 engine. it has got to be a 6.2l, 7.3l or 6.0l engine... at any rate none of these engines have a timing belt... unless you have some kind of import model that i am not familiar with. if that is the case them i will try to find out all the info i can.

Oct 26, 2008 | Ford E-Series Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...