Question about 2010 Toyota Yaris 1.3
Try undoing the the plug this should free the socket (wrench) and allow you to refit it. A length of hose pipe fitted to the plug when you first screw it in will help ensure you do not cross thread the plug.(If this is why the wrench is stuck you may have to seek proffesional help). Once the plug is correctly located you can then use the wrench to tighten fully.
Posted on Sep 07, 2016
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Spark plug torque on the 3.0L engine is 13 ft.lbs. and the 3.3L is 18 ft.lbs.
Valve covers-69 inch lbs.
Intake Manifold-11 ft. lbs.
Posted on Jul 07, 2014
Tips for a great answer:
Jan 12, 2015 | 2005 Infiniti G35 Coupe
Jan 04, 2012 | Cars & Trucks
Jun 21, 2011 | 2000 Mitsubishi Galant
May 23, 2011 | 1997 Toyota RAV4
Disconnect the negative battery cable. Remove the accessory drive belt. Using a 9/16mm wrench, loosen the power steering pump bolts, then slide the pump forward. Do not remove the power steering pump. Remove the power steering pump braces.
Disconnect the spark plug wires. Using a 9/16 mm wrench, remove the valve cover bolts. Lift the valve cover to remove it. Using a flathead screwdriver, gently nudge and remove the old valve cover gasket.
Clean the gasket seating area using automotive engine cleaner and a clean cloth rag. Make sure that all debris is removed. Place the new gasket into place. Apply gasket sealant and place the valve cover back into place.
Tighten the bolts securing the cover into place using a torque wrench. Reconnect the spark plug wires. Reinstall the power steering pump braces. Place the power steering pump back into position. Using a 9/16 mm wrench tighten the bolts that secured it into place. Reinstall the accessory drive belt.
Ensure that the negative battery cable is disconnected. Locate and remove the accessory drive belt. Using a 9/16 mm wrench, disconnect the bolt attaching the alternator to the brace.
Remove the brace to gain access to the additional parts that will be removed. Disconnect and remove the spark plug wire harness. Using a 9/16 mm wrench, remove the bolts securing the valve cover. Lift up and remove the valve cover.
Use a flathead screwdriver to gently nudge the old valve cover gasket to remove it. Do not scratch the gasket seating area when removing the valve cover gasket. Make sure that all debris and particles are removed from the gasket seating area.
Place the new gasket in the gasket seating area. Using a torque wrench tighten the valve cover gasket bolts. Reinstall the spark plug wire harness. Put the alternator brace back into position and tighten the bolt that secures it into place.
Reinstall the accessory drive belt. Reconnect the negative battery cable. Add oil to the car and start the engine. Allow the engine to run idle for 10 to 15 minutes. Drive the car a short distance to check for leaks.
Mar 16, 2011 | 1999 Oldsmobile Silhouette
Feb 18, 2011 | 2003 Saturn ION
Feb 04, 2011 | 2001 Daewoo Leganza
Dec 20, 2010 | 1998 Oldsmobile Eighty Eight
Dec 05, 2010 | 1998 Lincoln Continental
Apr 07, 2010 | 1999 Ford Taurus
49 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: