Question about 1999 Mitsubishi Diamante

1 Answer

I replaced the fuel pump in my vehicle today and after installing the fuel pump my vehicle will not start but would start before i replaced the fuel pump.. the vehicle is turning over but wont start.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mitsubishi Master
  • 46,272 Answers

Fuel system is air locked check pressure at the injector rail

Posted on Apr 17, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2004 grand am will turn overbut not start...fuel pump?


spray a quick mist of starting fluid into air cleaner hose. Reinstall. If vehicle starts then shut off, suspect possible faulty fuel pump relay, fuel pump fuse, fuel pump, or wiring

May 08, 2014 | 2004 Pontiac Grand Am

1 Answer

I need to replace the fuel pump on my 2001 Saturn L200 with a 2.2 L Engine. What is the best procedure?


Fuel Pump REMOVAL & INSTALLATION 1.9L Engine To prevent excessive fuel spillage, whenever the tank is removed from the vehicle it should be no more than 1?2 full. Removal of the fuel pump module assembly requires the removal of the fuel tank.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Fuel feed and return lines from the filter/pressure regulator
    • Fuel pump vapor line from the fuel tank vent pipe
    • Fuel pump module retaining ring with service tool SA9156E. A 1?2 inch breaker bar will loosen the lockring
    NOTE: To prevent bending of the sending unit float arm, lift the pump module up slightly to disengage the orientation tabs in the tank. Rotate the module 90 degrees clockwise until the fuel lines are facing the 1 o'clock position.
    • Fuel pump module from the fuel tank until the bottom of the pump module is close to the fuel tank opening
    • Tilt the pump module approximately 45 degrees to the right hand side of the tank and lift the pump from the fuel tank
    • Fuel pump to tank seal and discard it
    To install:
  4. Install or connect the following:
    • Fuel pump module into the fuel tank by orientating the float to face the right side and tilting the module approximately 45 degrees
    • Fuel pump into the tank and rotate the assembly 90 degrees counterclockwise to align the module tabs with the slots in the tank
    NOTE: The fuel pump retaining ring cannot be properly installed if the flange locator tabs are not aligned with the slots in the fuel tank.
    • Retaining lockring with tool SA9156E
    • Vapor line to the fuel tank vent pipe
    • Fuel feed and return lines to the filter/pressure regulator
    • Fuel feed, return and EVAP canister purge line in the fuel tank retaining clip
    • Fuel tank
    • Negative battery cable
  5. Start the vehicle and check for leaks, repair if necessary.
2.2L and 3.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Fuel tank
    • Fuel lines from the fuel pump module cover
    • Fuel pump module retaining ring with a Sending Unit Wrench, J43827
    • Pull the retaining clip toward the float arm and lift up
    • Fuel pump straight up from the fuel tank
    • Fuel pump tank seal and discard the seal
    • Fuel feed line from the bottom of the fuel pump cover with Clamp Pliers J43914
    • Fuel pump electrical connector Fig. 1: Remove the fuel pump cover lockring-2.2L and 3.0L engines 9306zg57.gif
    To install:
  4. Install or connect the following:
    • Fuel pump feed line to the cover
    • Fuel pump electrical connector
    • Fuel pump to the new seal
    • Fuel pump cover lockring with tool J-43827
    • Fuel lines and wiring harness
    • Fuel tank
    • Negative battery cable
  5. Start the vehicle and check for leaks, repair if necessary.
prev.gif next.gif

Jan 29, 2011 | 2001 Saturn L-Series

1 Answer

Where is the fuel filter on a 2000 Mazda Millenia 2.3 V6


Fuel Pump-Mounted Filter
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Fuel pump cover plate
    • Fuel lines from the fuel pump
  4. Raise the fuel pump from the tank.
  5. Remove the fuel filter assembly.
To install:
  1. Install or connect the following:
    • Fuel filter to the fuel pump. Lower the pump assembly into position
    • Fuel lines
    • Negative battery cable
  2. Start the vehicle, check for leaks and repair if necessary.
  3. Install the fuel pump cover plate.

Inline Filter
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable

bcd3f99.gif
Exploded view of an in line fuel filter and related components

  • Air intake hose and/or filter housing, if necessary
  • Fuel line clamps, if equipped
  • Fuel lines from the filter and plug the openings
  • Filter clamp bolt/nut by loosening them.
  • Fuel filter from its mounting bracket

  • NOTE Note the direction of the flow arrow on the filter so the replacement filter can be installed in the correct position.


    To install:
    1. Install or connect the following:
      • Fuel filter in its mounting bracket, making sure the flow arrow is pointing in the proper direction
      • Fuel lines to the fuel filter
      • Fuel line clamps, if equipped
      • Air intake hose and/or filter housing, if removed
      • Negative battery cable
    2. Pressurize the fuel system and check all connections for leaks.

    May 24, 2010 | 1998 Mazda Millenia

    1 Answer

    Location of fuel pump for 1992 subaru loyale wagon


    REMOVAL & INSTALLATION

    See Figure 1


    0900c15280067055.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Fuel pump assembly mounted under the vehicle-1.8L engine
    1. Release the fuel system pressure. Do not reconnect the fuel pump harness.
    2. Disconnect the negative battery cable.
    3. Raise and support the vehicle safely on jackstands.
    4. Clamp the middle portion of the hose connecting the fuel tank pipe and the pump to prevent fuel from flowing out of the tank when unfastened.
    5. Loosen the hose clamp and disconnect the hose.
    6. Remove the three pump bracket mounting bolts and remove the pump together with the pump damper.

    To install:
    1. Install the fuel pump and damper, and tighten the bolts securely.
    2. Install the hose and tighten the clamp screw to 9-13 inch lbs. (1.0-1.5 Nm).
    3. Install the pump bracket in position to the vehicle body and secure it with the bolts.

    Take care to position the rubber cushion properly.
    1. Connect the pump harness.
    2. Connect the negative battery cable and test the fuel pump for proper operation.
    3. Check for fuel leaks.

    TESTING

    1. Turn the ignition ON and listen for the fuel pump to make a growling sound. Turn the ignition OFF .
    2. Release the fuel system pressure. Disconnect the pump harness and crank the engine for 5 seconds or more. If the engine starts, allow it to run until it stops. Turn the ignition OFF and install the fuel pump connector.
    3. Disconnect the fuel hose at the fuel pump.
    4. Connect a gauge in-line using a T-fitting.
    5. Start the engine and measure the fuel pressure. If the fuel pressure is not 36-50 psi (248-344 kPa), replace the pump.
    6. Release the fuel system pressure and remove the gauge.

    May 22, 2010 | 1992 Subaru Loyale

    2 Answers

    I need to know find and replace the fuel pump on my 1995 cavalier


    This is what i was able to pull up for you to help you. please let me know if you need further asistance with your vehicle and I would be glad to assist you..

    Please do not forget to rate and comment about your experience with fixya today.

    Fuel System > Gasoline Fuel Injection System > Fuel Pump > Removal & Installation Removal & Installation
    CAUTION The fuel injection system remains under pressure, even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
    1. Relieve the fuel system pressure using the recommended procedure.
    2. Disconnect the negative battery cable.
    3. Drain the fuel tank, then remove the fuel tank from the vehicle.
    4. While holding the modular fuel sender assembly down, remove the snap-ring from the designated slots located on the retainer.

    WARNING The modular fuel sender assembly may spring up from its position. When removing the modular fuel sender from the tank, be aware that the reservoir bucket is full of fuel. It must be tipped slightly during removal to avoid damage to the float.
    1. Remove the external fuel strainer.
    2. Detach the Connector Position Assurance (CPA) piece from the electrical connector and detach the fuel pump electrical connector.
    3. Gently release the tabs on the sides of the fuel sender at the cover assembly. Begin by squeezing the sides of the reservoir and releasing the tab opposite the fuel level sensor. Move clockwise to release the second and third tabs in the same manner.
    4. Lift the cover assembly out far enough to detach the fuel pump electrical connection.
    5. Rotate the fuel pump baffle counterclockwise and remove the baffle and pump assembly from the retainer.
    6. Slide the fuel pump outlet out of slot, then remove the fuel pump outlet seal.
    To install:
    1. Install the fuel pump outlet seal, then slide the fuel pump outlet in the slots of reservoir cover.
    2. Install the fuel pump and baffle assembly onto the reservoir retainer and rotate clockwise until seated.
    3. Install the lower retainer assembly partially into the reservoir. Line up all 3 sleeve tabs. Press the retainer onto the reservoir making sure all 3 tabs are firmly seated.
    Gently pull on the fuel pump reservoir from retainer to assure a secure fastening. If not secure, replace the entire fuel sender.
    1. Attach the fuel pump connector.
    2. Fasten the CPA connector to the fuel sender cover.
    3. Install a new external fuel strainer.
    4. Install the modular fuel sender.
    5. Install the fuel tank in the vehicle.
    6. Connect the negative battery cable.
    7. Pressurize the fuel system and verify no leaks.
    65668fa.gif

    78e3288.gif

    a08c0f1.gif


    Jan 07, 2010 | 1995 Chevrolet Cavalier

    1 Answer

    I drove the vehicle home from work at lunch yesterday. When I attempted to start the vehicle, I didn't hear the usual hum of the fuel pump. Vehicle wouldn't start. It wouldn't start this morning (no pump...


    comman problem need to replace fuel pump. i would suggest having the complete fuel pump module installed sense the tank will need to be removed.

    Oct 28, 2009 | 1998 Chevrolet Tahoe

    2 Answers

    Ran out of gas wont start now


    if its petrol engine bang bottom of fuel tank while some one else cranks vehicle over if it starts good just pump jammed if it dont buzz to life and you cant hear fuel pump buzzing ceck for power to it if thats there replace pump. running out of fuel kills electric fuel pumps internally in petrol tanks.

    if its diesel you must bleed fuel system taking extreme care if you un do lines some very high pressure

    May 30, 2009 | 2000 Nissan Xterra

    1 Answer

    Vehicle cranks but won't turn over


    First you need to check for spark and if that is okay you need to check for fuel pressure/volume. sounds like a possible bad fuel pump. you can also try hitting the fuel tank with a rubber mallet while cranking. If the van then starts you need a new fuel pump

    Dec 28, 2008 | 2000 Ford Expedition

    1 Answer

    2002 Jeep Grand Cherokee Laredo 4.0L won't start


    Crank position sensors are a big problem in these vehicles. Scan the Jeeps computer and post any codes you come up with.

    Dec 27, 2008 | 2002 Jeep Grand Cherokee

    Not finding what you are looking for?
    1999 Mitsubishi Diamante Logo

    111 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mitsubishi Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8557 Answers

    Are you a Mitsubishi Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...