Question about Cars & Trucks

2 Answers

The best way to replace passangerside motor mount in 1991 4.3 GM blazer

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,422 Answers

Its tricky but can be done with a minimal amount of labor
Lossen the cross member at the trany and the mount bolts at the cross member don't remove bolts or nuts trans will drop slightly support it with a jack so it can be moved up or down .
If you have an engine hoist best way chain or strap to bolth sides mid front of engine so you can lift evenly .
If not you can use a nother jack and do it one side at a time .
There isn't going to be a lot of room to get at the mounts you can't jack from the oil pan you need to find a safe spot to raise on bolth sides .
Lossen the bolts that mount the side of the mount to the block what you need is play so you can remove the pivit nut and bolt one side bolts to the engine the other side of the bolts to the frame with a pivit bolt and a rubber peice between them .
The trick is get the pivit out them you can move the engine and trans enough to get at the frame and engine mounting bolts .
Its not easy but lifting or lowering the engine or trans 10 thousands of an inch will make the differance in the world as to how easy that pivit bolt comes out . And once it is out you should have little problem replaceing the mount

Posted on Apr 17, 2015

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 41,466 Answers

BEST way is pay someone else to do it . Smart way is the same . your way is put a jack under that side of motor and un bolt old and put in new one .

Posted on Apr 17, 2015

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1243 Answers

SOURCE: Trying to pull ****** out unbolted mounts and

do not have to pull the cv axle out , but you do have to pop it loose just before you lower the transmission out of the car.

Posted on Aug 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 02 blazer i want to put a motor out of a 98 in it will it interchange


Chevy Blazer Engine Swap Part 1 of 2 - YouTube

? 10:29
https://www.youtube.com/watch?v=Dt_7AKP2WcI
Aug 13, 2011 - Uploaded by Dave R
Replacing the engine in a mid-size Chevy Blazer 4x4 with oneout of a Jeep Cherokee 2wd. Original engine was low and motoroil and spun a bearing. ... Chevy Blazer Intake Gaskets Replaced & Cooling System Rebuilt - Duration: 16:45. by ... 4:02. 94 4.3l Vortec V6 GM (black motor) - Duration: 6:01. by ...

4.3 vortec engine removal - YouTube




Jan 01, 2016 | Cars & Trucks

1 Answer

Why does my blazer vibrate?


Have your motor mounts checked.

Dec 03, 2015 | 1991 Chevrolet S-10 Blazer

1 Answer

1998 Marquis heat/AC system stopped running


just did one , the heater motor quit , and nothing works , replace the heater / blower fan motor , under the hood , passangers side , you'll have to remove the windshield washer tank and i found it was easier to jack the passangerside up , remove the passangerside wheel and remove the screws from the plastic inner fenderwell , at least the back ones . sorry it isnt easier , but thats what i went thru

Jun 22, 2012 | 1998 Mercury Grand Marquis

1 Answer

Removing a starter from a 1991 chevy s-10 blazer 4x4 , 4.3L v6...


The starter is under the vehicle on the passenger side. The best way is to turn your wheels to the left so you can reach the top of the starter solenoid behind the passenger tire. First undo the nuts from the solenoid terminals, second loosen the bolts holding the bell housing for the flywheel and slide it over enough to make room, third undo the starter mounting bolts and the starter should come out easier. And just reverse the steps for installation.

Jan 07, 2011 | 1991 Chevrolet S-10 Blazer

3 Answers

1991 Chevy S10 Blazer 4.3 4x4


4170636.jpgThis is all I've got.Hope this helps?

Dec 20, 2009 | 1991 Chevrolet S-10 Blazer

3 Answers

Location of blower motor and relay(GM guy)


Behind the vacuum heater controls in the dash, they lead to a relay mounted there. That was the relay that was bad on my Dodge. It was a digital readout one.

Jun 30, 2009 | 1991 Chrysler New Yorker

2 Answers

Iwant to replace the Powersteering Pressurehose


they are all in tight spots, especially your car. the best is get someone with small hands or long pliers. they may be a b*tch to get off so plently of PBblaster may be needed, or a torch to heat up the fittings. if youre replacing the entire hose you could also just cut the line and take it piece by piece. messy but effective.

Apr 06, 2009 | 1991 Pontiac Grand Prix

1 Answer

1991 blazer 4.3 ,starts but dies


check FUSE LINKS as there is a run fuse link od GM products

Jan 14, 2009 | 1991 Chevrolet S-10 Blazer

2 Answers

1991 Chevy Blazer S10 window motor installation


http://www.a1electric.com/s10motor.htm. This link has pictures and step-by-step instructions. I found it and have both sides to replace. Hope this helps.

Aug 08, 2008 | 1991 Chevrolet S-10 Blazer

1 Answer

My blazer makes weird noises


sounds to me like the motor mounts might be loose mine was doing the same thing.

Jul 11, 2008 | 1991 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...