Question about 2005 Nissan Altima

Open Question

How do you turn off the security on a 05 Nissan altama

Change the crank shaft and out stl want start security light keeps coming on how do I by pass it

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
elias_sgr
  • 163 Answers

SOURCE: service engine soon

Check for any loose wire harness connection or bad contacts.

Posted on Aug 18, 2008

Ad
ovs5
  • 38 Answers

SOURCE: My car keeps shutting off

could be cam sensor fault or just even ecu may need remapping

Posted on Dec 12, 2008

  • 383 Answers

SOURCE: CRANK SHAFT POSITION SENSOR 20002 NISSAN ALTIMA

1st, Nissan had a recall on Crank position sensors for 2002-2006 Altima's. Check with you dealer before you go doing any repairs. You may discover you can get your car repaired at no charge.
NHTSA Campaign ID number :O7V527000
Symptom: Erratic behavior. Stalling and no starts and very difficult to diagnose due to the time frame in which the component actually malfunctions. The warranty should not be limited to the original owner.
I would also need more specifics as to which engine you have so I might assist you in where the location of the sensor is. The Altima had a 4 and a 6 cyl engine offered that year.

Posted on Apr 06, 2009

  • 6 Answers

SOURCE: need to change the stop light for 05 nissan maxima.

Open the trunk, from the inside remove the side trunk liner (by removing the plastic tabs the liner can be pulled back). Once the liner is pulled back you will need to remove two nuts which secure the tail light in place. Once the two nuts are removed you can start pulling the whole tail light assembly out. There are two other tabs that secure the tail light in place which may give you some resistance but the light should come out without too much force once the two nuts are removed.
Once the tail light is out you can change whatever bulbs you need to.

Posted on Dec 26, 2009

  • 31 Answers

SOURCE: MY NISSAN ALTIMA 2006 2.5

did you check the sensors and if you are getting fuel and spark

Posted on Sep 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Service engine soon


Check for any loose wire harness connection or bad contacts.

Aug 18, 2008 | 2002 Nissan Maxima

1 Answer

What else could be the problem?


did you reset the light after change of sensers as some require reset to come out of limp mode

Dec 26, 2013 | 2004 Nissan Quest

1 Answer

Engine check light is on, it cranks, diesel is coming to common rail but wont start.


run fault codes to find faulty sensors. Cam/crank position sensors. Check to see if the cam shaft is turning (broken timing belt)

Dec 26, 2013 | Nissan Cars & Trucks

1 Answer

My 1996 nissan quest gxe wont even power solinoid or starter when i turn key.dash lights come on only im positive its the factory security alarm.how can i reset it


this alarm system is reset with the key being turned in the door, lock and unlock the driverside door and then see if it starts if not then do the same to the pass/side and see if it starts if it doesnt then you may have a bad starter, the best thing to do is check for power at the small wire on the starter if theres power to the small wire with the key in the crank postion and there should be power on small wire if there is then replace the starter, hope this helps.

Dec 19, 2010 | 1996 Nissan Quest

1 Answer

Have a 93 cadillac fleetwood, changed key cilinder and computer, but pass key fault light still comes out and does not let engine turn on.


The security system is keeping the engine from starting. In order to manually learn the security, you should try the following. With a fully charged battery, and all accesories, including headlamps, and dome lamp off, turn the key on, crank the engine for a second, then release the key. Leaving the ignition on for ten miniutes, the security light will shut off. turn the key off, back on, then repeat. This needs to be done 3 times, after 30 mins, try starting the engine. It should have relearned, and start up. Good luck...coop

Dec 10, 2010 | 1993 Cadillac Fleetwood

4 Answers

Security light keeps going on, I'm not able to start it then... how do I disable this?


IF YOU AWAY FROM HOME. LIKE AT WORK, SHOPPING MALL OR STORE.WHEN YOU GET IN CAR AND IT DONT CRANK.PUT KEY IN THE IGNITION SWITCH AND TURN IGNITION SWITCH TO THE ON POSITION FOR 10 MINUTE.UNTIL YOU SEE THE SECURITY LIGHT TURN OFF. WHEN SECURITY LIGHT TURN OFF TURN OFF IGNITION SWITCH WAIT FOR 5 SECONDS. THEN TRY STARTING VECHICLE SHOULD START.TAKE VECHICLE TO DEALERSHIP.THEY WILL HAVE SCAN VECHICLE.YOUR PROBLEM COULD BE WORN IGNITION KEYS OR WORN IGNITION SWITCH ALSO FAULTY BCM.THE DEALERSHIP HAS TO FIX AND REPROGRAM THEFT SECURITY SYSTEM.IF YOU REPLACE KEYS, IGNITION SWITCH OR BCM. THE 10 MINUTE TRICK WILL GET CAR STARTED TO GET HOME OR SHOP.BUT DONT KEEP DRIVING BECAUSE IT WILL COME TO A POINT WHERE VECHICLE WONT CRANK AGAIN.

Nov 20, 2010 | 1999 Oldsmobile Alero

2 Answers

I just replaced the starter in my 2000 olds alero and now it wont start it keep flashing securty....it thinks it is benig stolen....how can I fix this


Most likely you replaced the starter because it wouldn't crank over. If this is correct and the security light was flashing before replacing the starter, then most likely you have a problem with the pass-lock system. If your ignition cylinder is located in the dashboard, you will need to remove it and replace the passlock housing.

Sep 27, 2010 | 2000 Oldsmobile Alero

1 Answer

Need to change the stop light for 05 nissan maxima.


Open the trunk, from the inside remove the side trunk liner (by removing the plastic tabs the liner can be pulled back). Once the liner is pulled back you will need to remove two nuts which secure the tail light in place. Once the two nuts are removed you can start pulling the whole tail light assembly out. There are two other tabs that secure the tail light in place which may give you some resistance but the light should come out without too much force once the two nuts are removed.
Once the tail light is out you can change whatever bulbs you need to.

Jan 09, 2009 | 2004 Nissan Maxima

5 Answers

2005 altima


A common problem on this vehicle is failure of the Crankshaft Position (CKP) Sensor. Failure of the CKP Sensor will result in the vehicle not starting. The cost to repair the CKP Sensor is estimated at $29.13 for parts and $26.00 for labor.

Jun 29, 2008 | 2005 Nissan Altima

Not finding what you are looking for?
2005 Nissan Altima Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...