Question about 2003 Mitsubishi Lancer

Open Question

I have a 2003 lancer and need to replace the ( - ) terminal as it is broke. How do I get broken one off? Thanks

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

techbuster
  • 5081 Answers

SOURCE: how do I replace a broken alternater belt on a

First pop the hood and find the serpentine and alternator belts on the left side of the engine compartment. The serpentine belt runs around four pulleys. The alternator belt uses two pulleys. They share space on the drive shaft so they are right next to each other.
Of the four pulleys using the serpentine belt, three of them are vertically in line (closer to the front of the car) and the fourth stands alone (closer to the cab). Of the three vertically in line, the middle pulley is the one used to adjust the tension on the belt.
You must first break loose the bolt in the center of the tension pulley (the bolt is facing the passenger tire) by turning it counter clockwise. Then leave that bolt and go to the bolt connected frame connected to the other side of the tension pulley (this bolt is facing the front of the car). Turn that bolt counter clockwise until the serpentine belt is loose enough to pull off. Replace the belt and tighten in the opposite order. Once the desired tension is reached, crank the car and run it for a few minutes. Finally cut the car off and check the tension, tighten or loosen as neccessary.

Posted on Oct 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring diagram of mitsubishi lancer 4G18 2003


Wiring diagrams are broken down into systems like lighting, engine etc. What system do you need a diagram for??

Mar 11, 2016 | 2003 Mitsubishi Lancer

2 Answers

2003 mitsubishi lancer with manual was recently towed, now check engine light is on always, and battery light and brake warning light both flicker on and off together ay the same time. any ideas?


It sounds that there might be a charging system problem. Check all connection to the battery terminals. If no success ther have your charging system checked

Oct 25, 2010 | 2003 Mitsubishi Lancer

1 Answer

Mits lancer 2003 , car broken into now wont start. got spark but no fuel pressure. fuel pump good had tank out and tested. was working fine until windows got broken into


check fuses and fuel pump relay, and sometimes a simple bump or jolt or short can set off the fuel pump safety switch and is usually locates in the trunk hidden or glove box.

Oct 26, 2009 | 2003 Mitsubishi Lancer

1 Answer

Engine has no compression


when the timing belt broke it also bent the valves,hence the broken rocker arm. pull the head and see the valves are bent

Apr 09, 2009 | 2002 Mitsubishi Lancer

2 Answers

2003 hyundai elantra gls front wheel stud broke


grab a large punch and hammer and knock out the old broken one. Push the new one in and re tighten. This will pull it into place and because it has splines it should not spin while doing so.

Apr 05, 2009 | Hyundai Motor 2003 Elantra

2 Answers

2003 Mitzubishi Lancer oil pressure light only when braking


Try replacing the Oil Pressure Switch/Sending Unit. It should only be a couple bucks at your local auto parts store.

Jan 07, 2009 | 2003 Mitsubishi Lancer

2 Answers

2003 Mitsubishi Lancer


so u have a CH/CG lancer

you would need to remove the two 10mm bolts from the coil packs and leads and then stick the smaller version of spark plug socket in remove them, bear in mind if u have a mivec motor the spark plugs MUST be Platinum :)

Oct 21, 2008 | 2003 Mitsubishi Lancer

1 Answer

2003 Mitsubishi Lancer


basic rules.

1 remove the cable.
2. use the right size socket and insert it to the plug.
3. loosen the plug and clean or replace.
4. tighten it back.
5. do it one at a time. it would be confusing to install the wires back if you pull them at the same time.

tnx 4 using fixya and tnx 4 asking,

drcool

Oct 21, 2008 | 2003 Mitsubishi Lancer

Not finding what you are looking for?
2003 Mitsubishi Lancer Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...