Question about 1996 Ford Windstar

1 Answer

We're is the oil sensor on a 1996 Ford sw windstorm van?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Under the alternator

Posted on May 17, 2015

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76846 Answers

SOURCE: Got a PO118 code for my 1996 ford Econo 150 van.

I work for Ford and have never seen this code, but the sensor must be on the fuel rail on the top of the engine, vans have a hot stall/hessitation issue from vapor lock, maybe this is part of the fix.

Posted on Mar 24, 2009

richie9911
  • 155 Answers

SOURCE: where is the oil pressure sensor located in a 1996 ford contour

I hope This photo will help.
11_20_2012_3_21_35_pm.gif

Posted on Nov 20, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 20001 Ford windstorm it starts and will run for a short time then thugs and turns off what should I check?


see if you can get the codes out of computer that would help you greatly then post on here what codes are in system.most of time its mass air flow or cam sensor.good luck,mike

Jul 17, 2016 | 2001 Ford Windstar

1 Answer

I have a 1996 ford 350 van it has a 5.8 engine in it, My problem is when I start it ,It fires right up after a few cranks but if its in park it will idle high and then stall out or if it been running for a...


Take it to AutoZone for a free diagnostic scan. Your local Ford dealer will charge you $100+ for the same scan.

It sounds like the idle control valve and/or the mass air flow sensor. The scan will accurately pinpoint the problem.

Jun 01, 2012 | 2002 Ford E350

1 Answer

Just changed the oil pan gasket in my 1996 ford windstar and its still leaking oil and there is oil all over the passenger side of my van ,where else can this leak be?


You have a front and rear main seal, if either of these are leaking the oil will be coming from the center of the engine above the oil pan. There are 2 1 in front and 1 in back of the engine.

Rate my answer.............Thanks

Dec 02, 2010 | 1996 Ford Windstar

1 Answer

Where is the oil sending unit on a 1996 ford taurus 3.0 liter engine located? glenn


On 3.0L OHV engines, the oil pressure sensor is located on the left side of the engine block above the flywheel. On 3.0L DOHC engines the sensor is located on the left side of the engine block above the oil filter. On 3.4L DOHC engines the sensor is screwed into the oil filter adapter. The oil pressure sensor operates the oil pressure warning lamp.

71f6e37.jpg
Fig. 1: Location of the oil pressure sensor-3.0L OHV engines


046f42b.jpg Fig. 2: Location of the oil pressure sensor-3.0L DOHC engines

69cce3e.jpg

Fig. 3. The oil pressure sensor-3.0L OHV engine

Hope help with this (remember rated this help). Good luck.

Feb 18, 2010 | 1996 Ford Taurus

1 Answer

Where is oil pressure switch in chevy lumina van 1996?


To locate the oil pressure sending unit, locate the oil filter and look above it and to the right, above the starter. You will see a long round sensor, this is the oil pressure sending unit. It screws into the engine block and when you remove it you will get a dribble of oil.

Jan 23, 2010 | 1996 Chevrolet Lumina Mini

1 Answer

Start up 1996 ford windstar ,runs great,get the van up to operating temp,shut off van and try to restart 15 mins later its very hard to start.....if you leave it and come back when it's cold it will start...


Not your camshaft sensor, it would not even start. Your going to have to get it scaned, but I'm thinking it may be your EGR system.

If you are comfortable performing some basic checks prior to resorting to the Ford Dealer then try pulling a vacuum on the EGR valve to make sure the pintle moves freely in both directions. While you're at it, make sure all vacuum hoses and system components hold a vacuum. Inspect the EGR valve visually for coking and contamination. Check EGR solenoids and the position sensor for electrical continuity.

Good luck and hope this helps.

Apr 13, 2009 | 1996 Ford Windstar

1 Answer

Cant find gearbox oil plug escort van 1996


locate the filler plug on the lower front side of the transmission housing unscrew it with an allen key if the oil is low top up until it runs back out the filler hole. this is for manual transmission

Apr 04, 2009 | 1996 Ford Escort 4 Door

1 Answer

Got a PO118 code for my 1996 ford Econo 150 van.


I work for Ford and have never seen this code, but the sensor must be on the fuel rail on the top of the engine, vans have a hot stall/hessitation issue from vapor lock, maybe this is part of the fix.

Mar 24, 2009 | 1996 Ford Econoline

Not finding what you are looking for?
1996 Ford Windstar Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...