Question about Cars & Trucks

1 Answer

My machine occasionally stops working in reverse but runs ok in forward. if I lower the stabilizer a little and slowly raise it, it sometimes kicks back into drive (only a reverse issue). Any Ideas?

Posted by on

  • Mark
    Mark Apr 16, 2015

    This is a Case 590 Super M loader backhoe

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 1,511 Answers

The transmission reverse gear is defective.

Posted on Apr 16, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can you remove a leaf or 2 to lower the rear. My 2001 Sierra 2wd, SLE has 116k miles and runs great. Wanted to change stance with front a little higher than rear but can't afford lift kit...and the...


removing leaf springs is not recommended as it lowers the stability and load carrying capabilities
to do what you want you have the spring camber reset to flatter measurements
Camber is the distance from the spring eyes to the center bolt measurement when the springs are out of the vehicle
resetting the springs to reduce that measurement will do what you want
However it is pointed out that while it makes the vehicle look cool it creates more problems than it is worth , in steering geometry, tire wear , braking stability , handling stability and general driving comfort and in many cases will make the vehicle ******* on the road

Oct 29, 2017 | Cars & Trucks

1 Answer

Transmission will only run in reverse


Sounds like the torque converter, pump are working. It must be the clutch pack for the forward gears if all the linkage is still ok.

Sep 14, 2014 | Cars & Trucks

2 Answers

When reverse is selected idle speed increases very little but no movement


Soun like a problem with the Torque Converter or valve solanoids stucked. FIrst checl trans fluid level in good conditions (without brun smell odor and clear colors).

Jul 20, 2012 | Cars & Trucks

1 Answer

I have a 2005 Spectra 5 Auto Trans. My brother was checking fluids for me and noticed when I put car in reverse, the engine raised a little and when I pulled forward the engine lowered again. Is this...


It is normal for the engine to move a little, but if it moves quite a bit tou could have a broken motor mount. If a mount is broken you will usually hear a thump in the vehicle either when put into gear or upon acceleration or deceleration.

Sep 12, 2011 | Kia Spectra5 Cars & Trucks

1 Answer

Can not remove rear drum


Is the emergency brake on? If so release it the brake shoes should release the drum. Second option is to spray some WD40 on the threads next to the drum and replace the wheel putting the lug nuts on finger tight. Lower the vehicle and slowly drive forward for a couple of feet and slam on the brakes, then do the same in reverse. Raise the vehicle and remove the wheel and see if the drum is loose or give the drum a couple of whacks with a rubber hammer.

Jun 23, 2010 | 2000 Ford Windstar

1 Answer

94 mitsubishi 3000gt transmission problems


have you tried changing the transmission ecu ?

Jun 29, 2009 | 1994 Mitsubishi 3000GT

1 Answer

Remove seat from second row in Honda Mini Van 2007


on the passenger side feel under the seat and there is a lever that pulls toward you as you stand at the sliding door.

First, raise the armrest, then lower the back all the way forward. Then remove the headrest sit it out of the way and while pulling the lever under the seat towards you, lift up the seat from the back so it tilts forward. When it is standing on its "nose" lift first one side shifting it either forward or backwards to clear the rod on which it is hooked. Do the same with the other side of the seat and then lift it out. Installation is the reverse of removal.

The other seat is much the same, though sometimes the lever is a little different but in the same place.

Good luck,
bob

Jun 07, 2009 | 2006 Honda Odyssey

2 Answers

4x4 won't move!


the transmission is slipping

May 08, 2009 | 1997 GMC Jimmy

1 Answer

Jerky accelerating, late response to gas being pressed


Well for one, make sure you speed up slowly, dont HIT the accelerator. It may also be problems with your fuel filter. After you are stoped fuel stops running through the fuel pump/filter and then when you start going its starts to run through again and it cant keep up so it gets bubbles in it and doesnt move throught the filter easily hence the jerky accelerating. Good Luck

Apr 17, 2009 | 2000 Oldsmobile Intrigue

1 Answer

Front axle how to remove half shaft


Hi.. The step to remove the front Axles of you Vitara.
Raise and support Vehicle . Remove front wheel,
Drain Diff,fluid,
Remove Locking Hub if is equipaded,
Remove Circle clip from axle shaft
On right side of Vehicle, Remove the Stabilizer Little ball joint nut. Remove castle nut Front Tie rod end,
Remove mounting bolts from brake calipper,
Remove Calipper from steering knuckle and wire a side.
Remove Stud Nut from steering knuckle,
Support Lower suspension arm with a jack,
Remove lower strut bracket bolt ,
Lower jack and disconnect Knuckle from lower suspension crontrol arm,
Pull Outler joint from Hub.
Use Large screwdriver or Prybar To pry Right inner joint from differential, The axle will go out making a little froce with the prybar,
To remove the left side,
Remove mounting bolt from inner joint flange,
Pull out axle from hub.

To reinstall just reverse the prosses.

I hope this help on your job...
Thank you for use fixya....


Aug 18, 2008 | 1999 Suzuki Vitara

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...