Question about BMW 318

Open Question

What does fault code c115 in bmw 318 2008 model

Posted by on

  • Imran Apr 16, 2015

    Pls help ASAP much obliged

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My BMW 2002 starts out good in morning but when it gets warm or hot my transmission failsafe light comes on what can I do


BMW has been using electronically controlled automatic transmissions in most models since the late '80s. These transmission systems employ a transmission control unit which controls electrical solenoids to manipulate the various control and shift valves and functions in the transmission valve-body. When the transmission control unit detects a problem that it "thinks" could be damaging to the transmission or engine, it goes into a fail-safe or "limp" mode. In this mode, the transmission will function in reverse normally, but in forward it will operate in only one gear (whether you have the shifter in D, or any of the lower gears). This will typically be 3rd or 4th gear, depending on the model. It will start in this gear and stay in this gear with no shifting. You would experience this as sluggish acceleration and higher than normal engine speed at about 40-mph and above.
If you must drive the vehicle when the transmission is in the fail-safe mode, accelerate gently and keep the road speed lower than full highway speed.
Earlier models do not employ fault codes and must be diagnosed manually. Late models do employ fault codes and a diagnostic/scan machine can be used to check and read the faults to assist in diagnostics. Note that this is not your common OBD-II engine management fault code tool. This is what A BMW dealer or a properly equipped independent shop would have for full vehicle system diagnostics and coding operations.

Jun 15, 2017 | BMW Cars & Trucks

1 Answer

BMW 630 2008 model. Entertainment system freezes and stays on even when car switched off.


Have the codes read (oBD!!) I would suspect over voltage. This over voltage plays havoc with car systems and show many times on bmw as idrive screen faults and freezes. If codes read over voltage, replace alternator. Don't just replace regulator, not worth the hassle, regulator is attached to alternaor, get a refurb unit, bmw prices are silly.

Feb 26, 2017 | BMW Cars & Trucks

1 Answer

Bmw N42 motor wont run


My guess is you blew the motor rebuilt it and never changed the catalytic converter.

Nov 06, 2016 | BMW Cars & Trucks

2 Answers

After driving for short distance it won't start I have tried every thing on the book on my BMw 318i m40 1992 model


have you tried having the fault codes reading section of the book
It is the first line of the trouble shooting
it appears that there is an electronic part break down for over heating
it could be in the ignition control module, ECM, coil/s, immobilizer
try exchanging the ECM with a known good one and fix any faults shown on the code scanner

Feb 26, 2016 | BMW Cars & Trucks

1 Answer

Where is the trans range sensor located on a 2004 BMW 545 I


BMW transmission range sensor position Vehicle Parts ...

www.fixya.com/tags/transmission_range_sensor_position/auto.../bmw
BMW vehicle parts & accessories transmission range sensor position related ... i got a transmission fault warninig my bmw car 545i E60 it is a 2004 E60 bmw car ...location transmission dipstick 1997 bmw 328is if its a manuel transmission it ...

P0705 Transmission Range Sensor TRS Circuit Malfunction

www.obd-codes.com/p0705
Transmission Range Sensor Circuit Malfunction (PRNDL input) ... Later models with the transmission range sensor located in the valve body are a different ball ... What causes the P0705 code on a BMW 740i ('97) ... 2004-2015 OBD-Codes.com.Missing: 545

Nov 25, 2015 | BMW Cars & Trucks

2 Answers

How do you reset reset the service light on a Bmw 320, 2008 model


How to Reset the 2006-2011 BMW Maintenance Light …: http://youtu.be/g4ebeJ3uzw4

May 20, 2015 | BMW 320 Cars & Trucks

1 Answer

2006 BMW 750 Li My dynamic drive inactive light came on, then a generator fault light came on


BMW has been using electronically controlled automatic transmissions in most models since the late 80s. These transmission systems employ a transmission control unit which controls electrical solenoids to manipulate the various control and shift valves and functions in the transmission valve body. When the transmission control unit detects a problem that it thinks could be damaging to the transmission or engine, it goes into a fail-safe or limp mode. In this mode, the transmission will function in reverse normally, but in forward it will operate in only one gear (whether you have the shifter in D, or any of the lower gears). This will typically be 3rd or 4th gear, depending on the model. It will start in this gear and stay in this gear with no shifting. You would experience this as sluggish acceleration and higher than normal engine speed at about 40 mph and above.

If you must drive the vehicle when the transmission is in the fail safe mode, accelerate gently and keep the road speed lower than full highway speed.

Earlier models do not employ fault codes and must be diagnosed manually. Late models do employ fault codes and a diagnostic/scan machine can be used to check and read the faults to assist in diagnostics. Note that this is not your common OBDII engine management fault code tool. This is what A BMW dealer or a properly equipped independent shop would have for full vehicle system diagnostics and coding operations.

Feb 13, 2015 | 2006 BMW 750Li

1 Answer

How do I do my BMW e46 320i 2002 model is misfiring is not polling at all?


run fault codes and look for injector faults an d pressure problems. check HT leads

Dec 24, 2014 | BMW 320i Cars & Trucks

1 Answer

Engine light is on on bmw 1988 735 i


The computer has detected a fault in one or more of its systems. The only way you're going to an answer as to what the fault is, you're going to have to have someone attach a scanner or code reader to get any codes that are stored.
Most auto part stores can check late model OBD II for free. One may do earlier European.

Oct 14, 2011 | 1988 BMW 7 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...