Question about 2002 Ford Crown Victoria

1 Answer

Where is the freeze plugs for a 2002 crown Victoria

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 372 Answers

Most v8 engines have 8 to 10 of them, most will be on the sides of the block below exhaust manifolds, others will be back of block and will require pulling either motor or trans to replace

Posted on Apr 16, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
97crownvic
  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

CLEONTI
  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

  • 93 Answers

SOURCE: 2000 crown victoria serpentine belt installation

Accessory Drive Component Locationsa0011762.gif

Posted on Jun 09, 2009

ZJLimited
  • 17970 Answers

SOURCE: i need drive belt diagram for a 2002 ford crown

2002 FORD CROWN VICTORIA - V8 4.6L 281ci CNG FI N 9
and
2002 FORD CROWN VICTORIA - V8 4.6L 281ci GAS FI N W

Belt Routing Diagram - Multiple Accessory

f091bd1.jpg


Hope helped (remember rated this).

Posted on May 26, 2010

  • 977 Answers

SOURCE: what is the fuse panel diagram 2002 ford crown

check inside the cover of the fuse box under the hood there may be the diagram there.....hope this helps......cheers

Posted on Jul 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have antifreeze coolant leaking from the rear of my engine and want to gain excess to my rear freeze plugs. Do I pull my transmission to change the rear freeze plugs on the 1989 crown Victoria?


Yes, you have to pull the transmission. But look it over closely. Most likely the coolant is coming from somewhere else. I have never seen or replaced a bad freeze plug back there. Water can't get to them to rust them out from the outside in. Only if you use water only to cool the engine. Heater hoses and the intake manifold gaskets can cause a leak in this area.

Apr 25, 2015 | 1989 Ford Crown Victoria

1 Answer

Do I need to pull the transmission to replace freeze plugs in the 1989 crown Victoria?


depends which freeze plugs your changing. if its the ones at the rear of the heads or back of motor being covered by the bell housing then yes it has to be pulled.

Apr 25, 2015 | 1989 Ford Crown Victoria

1 Answer

Location of freeze plugs on 1998 crown victoria


on both sides of engine,on front and rear of cylinder heads and the dreaded on back of engine between motor and transmission

Dec 31, 2012 | 1998 Ford Crown Victoria

1 Answer

What does a glow plug light look like?


The 2002 Crown Victoria was not offered in a diesel engine so there is no light for glow plug

Dec 07, 2012 | 2002 Ford Crown Victoria

1 Answer

Where are the spark plugs located on a 2002 ford crown victoria


They should be located at the top side of the valve covers under the coils.

Jan 18, 2011 | 2002 Ford Crown Victoria

1 Answer

How to replace a heater valve of a 2002 crown vic?


Heater valve or core? Heater control valve is as simple as loosening clamps and pulling hoses off. Reverse to install. Fill with anti-freeze.

Dec 18, 2010 | 2001 Ford Crown Victoria

1 Answer

Antifreeze leaking from rear of 4.6 liter engine in 1994 Crown Victoria


Will be coming from either bad freeze plug(s) [most likely], a heater hose that is dripping so that it is running off the back side of the engine, or a leaking intake manifold that is located such that it is running off the back side.

Jun 24, 2010 | 1994 Ford Crown Victoria

1 Answer

I need drive belt diagram for a 2002 ford crown victoria


2002 FORD CROWN VICTORIA - V8 4.6L 281ci CNG FI N 9
and
2002 FORD CROWN VICTORIA - V8 4.6L 281ci GAS FI N W

Belt Routing Diagram - Multiple Accessory

f091bd1.jpg


Hope helped (remember rated this).

May 26, 2010 | 2002 Ford Crown Victoria

1 Answer

1997 Crown Victoria: 92 crown victoria get no spark...


Attempt to change all of the spark plug wiring and spark plugs. Then start the vehicle.

May 18, 2010 | 1997 Ford Crown Victoria

1 Answer

Where and how do you change freeze plugs in an 1988 ford crown victoria


theyre located on the sides of the block, about the size of a silver dollar, pop the old ones out with a screw driver, install new with a soft rubber malet. drain eng. coolant first though as you will leak antifreeze once plugs are removed

Apr 05, 2010 | 1988 Ford Crown Victoria

Not finding what you are looking for?
2002 Ford Crown Victoria Logo

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...