Question about Cars & Trucks

1 Answer


Posted by Anonymous on



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 10,263 Answers

Old panel from what? Need a better idea of what you're doing.

Posted on Jun 05, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I remove the rear door panel from a 2004 Buick Rainier

If dog ate the old ones, trim away old remaining material and gently pry the panel away from the door's edge. You should be able to see the shaft of the plastic retention clips which are just push-fit into door.

Jul 12, 2015 | 2004 Buick Rainier

1 Answer

How do i remove the old hood release cable/

First disconnect the cable and hold downs from under the hood, next remove the kick panel, remove the panel and cable, using plyers, unclip the cable retainer from the panel...reverse the order to put it back together.

Jun 01, 2015 | 1990 Cadillac Deville

1 Answer

Need to replace right side mirror with new unit. How to remove old unit?

you will need to remove the inner door panel to get to the nuts on the inside of the door panel to remove the mirror.if its just the mirror that is broken(reflective)then a glass place can replace the reflective part by gluing a new one onto the old housing.

May 09, 2011 | Pontiac G8 Cars & Trucks

1 Answer

How to install a new power window motor in my 1993 Mercury Grand Marquis? I have a 1993 Mercury Grand Marquis Ls and the power window doesn't work. So then I bought some new window motors and I was...

Remove all screws to door panel. Remove the lock and window controls. Then take large flat-tip screwdriver and gently pry directly next to plastic studs holding panel on to door. Lift door panel off. Remove plastic out of the way. You will now have access to window motor. You may have to solder off old wiring. Or if you have enough to cut, would be good

Sep 11, 2009 | 1993 Mercury Grand Marquis

1 Answer

I need to replace the whole rear tail gate lamp assembly.

Yeah remove the inside panel to get to those bolt, they should be 10mm nut.

Aug 12, 2009 | 2008 Toyota Sienna

1 Answer

How do I remove the drivers side inner door panel.

Best thing to do is go to Auto Zone and buy some extra door panel clips, the old ones will most likely break and when you try to place the door panel back on you can't. The clips are not that expensive and Auto Zone can give you the step by step instructions and tell you what tools your going to need to remove the old clips with out damaging the door panel. If you don't want to buy the door panel tool, Auto Zone also has a tool loner program. 
Good luck and hope this helps. If you need instructions, keep me posted and be glad to help.

Jun 07, 2009 | 1995 Pontiac Grand Am

1 Answer

Replacing passenger wing mirror on ford fiesta finesse 2000

yes it is better to remove the whole panel, the panel slides down over the top of the frame of the door. remove the clips on the door carefully though as when these clips get old they become fragile and snap quite easily.and then remove the secondary panel for the mirror.

Apr 30, 2009 | 2003 Ford Escort

1 Answer

Driver side mirror installation (and removal of old)

Inside the pull cavity on the window switch bezel there is a cap in the bottom of the cavity.Remove this cap and there are 2 screws there you need to remove,then remove the window switch bezel.
There will be a screw there in the door panel where the bezel was covering up,remove this.
Under the door handle you will see a small square cover,remove this and you will see another screw you need to remove.
You will see 2 more screws at the bottom of the panel you need to remove.
Then lift up on panel and remove.
You will then see 3 nuts holding mirror on,remove these and remove mirror.

Apr 03, 2009 | 2003 Lincoln Aviator

1 Answer

Remove right rear door panel

  1. Remove the rear door power window/power door lock switch
  2. Remove the door handle bezel. Remove the door trim panel screw located behind the door handle bezel.
  3. Remove the door trim panel screws located by the armrest handle.
  4. Remove the door trim panel using J 38778.
  5. Disconnect the electrical connectors.
  6. Remove the door trim panel from the door.

IMPORTANT: Discard the old door trim panel retainers and replace with new retainers before installing the trim panel

  1. Install new trim panel retainers to the rear door trim panel.
  2. Connect the electrical connectors.
  3. Align the door trim panel retainers to the door.
  4. Press the door trim panel at the retainer locations until the retainers are fully seated.
  5. Install the trim panel screws. Tighten Tighten the door trim panel screws to 2 N.m(18 lb in) .
  6. Install the power window/power door lock switch

Nov 04, 2008 | 1998 Oldsmobile Intrigue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79024 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13652 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides