Question about Cars & Trucks

1 Answer

1996honda accord 5 speed won't go in gear only when motor not running makes grinding noise

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 42,108 Answers

The clutch is not disengaging
if cable --replace the cable
if hydraulic bleed the air out if the system or replace the clutch master /lave cylinder

Posted on Apr 15, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

j_del
  • 1586 Answers

SOURCE: Reverse gear has grinding noise...?

Have them flush the fluid out under warranty and put in new fluid, and have them bleed the clutch lines in case air is getting in there. Audi and VW claim lifetime transmission fluid but it's BS - I've changed relatively low mile fluid from these cars and it was horrendous. It's possible that the fluid itself is causing trouble, but it's more likely that it is a synchro problem. If it was a clutch issue, you should have problems with more than just reverse gear - a clutch simply engages and disengages the engine and transmission, regardless of which gear it is. The problem (if not fixed by fluid) is in the transmission, and being under warranty, don't accept another "suggestion" like they're giving you. Changing your clutch isn't gonna do it.

Posted on Aug 12, 2008

  • 508 Answers

SOURCE: 5th. Gear

Sounds like you may have bent a shift fork or your cluster gear has some missing teeth on it now. I would venture to say that is it a bent shift fork. This will require the transmission be removed to gain access to inspect and repair.

Posted on Feb 16, 2009

emissionwiz
  • 75817 Answers

SOURCE: 5-speed transmission making noise in 3rd and 5th gear

are u sure the alignment (side to side, up and down) of the trans on the bell housingis not out of spec, that will burn the bearings out very quickly.

Posted on May 04, 2009

inhisname
  • 76 Answers

SOURCE: 2004 Honda Accord A/C Blower Motor Make Noie !!!

hello, it sounds like the fan motor was knocked out of balance (they are palstic).. you can try to remove fan and try to repair balance...good luck marty

Posted on May 27, 2009

  • 14 Answers

SOURCE: my drivers side headlamp motor keeps running after

It sounds like the gear is stripped. This happened to mine. See my other post for fixes.

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Grinding/whining noise from gearbox/final drive - fiat 500C Lounge - 2010 model


I think removes the tyre both then check its gear box bearing noise or clutch plate bearing noise

Dec 16, 2013 | Cars & Trucks

1 Answer

PLEASE HELP Metal grinding while driving


Sounds like the thrust bearing is worn to the bleep. Though I suspect it's not Synchromeshing. Some part of the Clutch mechanism failing critically.
See http://en.wikipedia.org/wiki/Manual_transmission#Synchromesh
http://en.wikipedia.org/wiki/Clutch
Did it run out of Oil? BUT then maybe damage has been done to both the internal of the Gearbox as well as the clutch, so yeah STOP driving it before more damage that can set you back a fortune

May 15, 2013 | 1996 Honda Accord

1 Answer

Why is second gear starting to make grinding noises when shifting?


Its because the baulk rings on the syncro are worn ,this is caused by bad driving technique ,ie going to fast when changing down and not allowing the time needed for these baulk rings to creater friction which allows the gears to be running at the same speed .or a boy racer has given the car a thrashing .

Feb 22, 2013 | 1993 Honda Accord

1 Answer

I have a 1989 z24 cavilier and i just changed the slave cylinder and now when i start it and press the clutch it makes a grinding noise. When i try to put in gear it wont go in any gears and makes some...


hi i was wondering if anyone can tell me whats going on with my 89 z24 cav i just replaced two shifter cables on she's a 2.8l 5 speed and now when i starts her and lets the clutch out she dosen't engage at all but she has no noises and no grinding goes in gear fine but just won't move hope someone can help thanks

Jul 04, 2012 | Cars & Trucks

1 Answer

TAPPING NOISE, NOW IT WON'T GO INTO GEAR WITHOUT LOUD GRINDING NOISE AND ACTS LIKE TRANSMISSION WON'T ENGAGE TO DRIVE


If it is an automatic transmission, first check the fluid level. If it is low, fill it up and try it again. If the level is fine, then there is a bigger issue and you should seek a professional's help.

Jun 18, 2017 | 1996 Buick Century

1 Answer

I have a 99 Honda accord that makes a loud grinding noise when switching gears from park to reverse and won't go. It is automatic transmission. What could be the problem


Based on Info...
Possible Sun Gear Failure, or Other Internal.
Check Fluid Level. Although it Seems Damage is Done.
Remove and Replace.

Jul 28, 2011 | 2000 Honda Accord

2 Answers

I have a 1998 Honda accord lx 4 cylinder that makes a grinding noise up front only when driving, not while stopped. I have changed brake pads, rotors, calapers, cv joint, and wheel bearings. The tires are...


Is the sound constant with the speed of the vehicle or speed of the engine? Does applying the brakes or turning change the noise? Does the grinding sound like metal to metal contact?

Jan 02, 2011 | 1998 Honda Accord

1 Answer

I have an 1989 GMC Sierra K1500(4x4)5-speed. grinds when going...


It may be the transmission input shaft bushing or bearing, located in the rear of the engine crankshaft, in front of the clutch assembly. If the bushing or bearing is dry (needs to be greased), the input shaft will still try to turn with the engine rpm, even though the clutch pedal is depressed. Also, the clutch disc may not be fully releasing, which could possibly be corrected by adjusting the clutch pedal linkage. good luck

Jul 26, 2017 | GMC Sierra 1500 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...