Question about Hyundai Motor 1999 Elantra

1 Answer

I have a crank and no start issue my dash lightsSRS,e brake,oil,battery,wont come on and no turn signals when i turn the key

The interior fuse panel has no power to any of of the the fuses checked them all there all good i checked the fuses under the hood again all good but these have power checked the spark plugs there all good gaped to .40 but still no start when i turn the key...

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hyundai Master
  • 10,875 Answers

The connection on the firewall is corroded,pull your fusebox and check behind it,it could be burnt too

Posted on Apr 15, 2015

Testimonial: "ill take a look behind it also the transmission interlock wont release from park"

  • 2 more comments 
  •  johnny rebel
    johnny rebel Apr 16, 2015

    https://youtu.be/rW5aLjR39qw

  •  johnny rebel
    johnny rebel Apr 16, 2015

    https://youtu.be/rW5aLjR39qw

  • Justin
    Justin Apr 16, 2015

    Ok so I pulled the interior fuse panel every things clean but I was looking the manual and found the wiring diagram there's a thing called "b+" I guess its part of the antitheft so it says well I found the 20amp relay for it way up under the dash with the hazards/turn signals but I don't know how to tell if its any good because when my car died abruptly on me there was 2 blown 10amp fuses that went out and one of them is labled "b+ antitheft" so I guess its a huge fuse system all for the ignition

  •  johnny rebel
    johnny rebel Apr 16, 2015

    your anti theft may be fried,look for a steering console with keys ,then switch everything in half the time,dont forget to get the door locks to,because your keys wont work in the ign

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I forgot to unhook the battery and relay wheni put a new fuel pump in my 2007 trailblazer now it wont crank or make any sounds just signals come on the dash


As long as the key was off and fuel pump relay not energized, you should have had no problem.
Check the pcm B fuse in diagram.
fuel pump-14xnoeoh11hcd40wqw2fpa52-1-0.jpg

May 26, 2017 | Cars & Trucks

2 Answers

Car won't crank, key stuck in ignition?


Depends on the car. Could be an immobilizer if your car has a security system.

Jan 11, 2015 | Cars & Trucks

1 Answer

Cranks but wont start


Try to have codes pulled to see if any codes relate to the starting issue.

Dec 29, 2013 | Ford Cars & Trucks

1 Answer

Where is the interior fuse box on a 2004 ford explorer


The fuse box is located under dash above your parking brake.

Jan 01, 2013 | 2004 Ford Explorer

1 Answer

F150 wont start replaced pump module on rearchassis now eng wont crank


Sounds like an issue with the fuse for the starter motor relay, or the starter motor relay itself.

The fuses for the starter system are F101 & F102
The starter motor relay is in the cab fuse panel.

The other thing to check if turn the key from off to run, press and hold the brake, and shift the truck into neutral and try starting with the brake still applied. This is testing the DTR ( Digital Transmission Range ) Sensor on the transmission. Should have no impact on what you did, could just be coincidence that the no crank no start issue just started.

Jan 11, 2011 | 2005 Ford F-150

1 Answer

My 2002 GMC Envoy wont start. I have had it on the battery charger for almost an hour. When I turn the key I get interior lights and headlights and the dash board lights up to. But nothing from the...


try car to car boost-battery charger may not be working correctly or set on low amp charge -interior lights and dash may all light but battery may not be strong enough to energize starter have battery tested if battery good than check for power to the starter if power-- starter may be shot can remove also and have tested at most auto stores free if no power battery -wiring-or connection issue would need to test fuse panel-ignition switch and starter solenoid

Jan 25, 2010 | 2002 GMC Envoy

2 Answers

I have a 1999 sti version 6 and it wont start even after ive entered the keypad numbers it turns over but wont start i


1. Locate the EFI main relay in the upper left side of the dash. Check the two Red wires for battery voltage with the key on. Check the Light Green wire for battery voltage from the computer key on.

2. At the computer check terminal 79 for battery voltage key on. Terminal 79 is a Yellow wire.

3. Check all power and ground inputs to the computer.

4. If the power and ground inputs are good at the computer check for a shorted 5 volt reference at the throttle position sensor and the boost sensor. A shorted 5 volt reference can cause no start, no spark with no injector pulse. 1. Check for the AC voltage waveform from the Crank sensor making it all the way to the PCM. On this Subaru, if it had a crank sensor signal, no cam sensor signal, you would see injector pulse, no spark. If it had cam sensor signal, no crank sensor signal, you would not see spark or injector pulse. Hope i helped if any more ?'s feel free to ask.....

Nov 10, 2009 | Subaru Impreza WRX STi Cars & Trucks

2 Answers

04 chevy 2500HD start relay /Circuit braker turns off @ key crank


Make sure battery has a full charge and battery connections all good. Any fuses in the diagram, test for voltage, some are hot all the time, some go hot with the key on.
Use a digital multimeter across battery posts, everything off, the generic spec for a full charge is around 12.6 volts. Leave the leads hooked up to battery, have a helper turn key to crank, how far does it drop? In my opinion it shouldn't drop much under 10 volts, I wouldn't argue with 9.6 volts.
2500 starter 1-h5vtzulw5yduyapxqxcg0ngy-5-0.jpg

impala starter 2-h5vtzulw5yduyapxqxcg0ngy-5-2.jpg

Mar 28, 2017 | Chevrolet 2500 Cars & Trucks

3 Answers

Change oil light remains on after oil change and light over license plate does not work after bulb change


To reset the Change Oil Light: Open driver's door and open fuse access panel
Turn ignition key to on (don't crank the starter) Push reset button located in fuse panel When Change Oil Light starts to flash Press and hold reset button until it beeps and light goes off Repace panel

Jul 17, 2008 | 2003 Oldsmobile Alero

Not finding what you are looking for?
Hyundai Motor 1999 Elantra Logo

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...