Question about 2002 Hyundai Santa Fe

1 Answer

What size rotors do I need to get for the front it 4 wheel drive and a 2.7 V6

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Hyundai Master
  • 531 Answers

You don't have the option to use different sizes?

Just goto the parts store or look at their site, but the main difference is you have to know if that vehicle is 2WD or 4WD to get the correct rotor!

Posted on Apr 15, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need to know what size rotors I need for the front is a 4 wheel drive a2.7 V6

Bryan: the rotors are different on your car from front to back. I would go online to : then enter your car and under keyword at the top, type in rotors. They will show you all that fit your car.

Apr 15, 2015 | 2002 Hyundai Santa Fe

1 Answer

Where is #5 plug how does it come out?

i you have a v6 or a v8 engine usually the #1 cyl is on the front right of the engine, odd number on one side even number on the opposite side ex: below

left 2 4 6 2 4 6 8
v6 front v8
right 1 3 5 1 3 5 7

you need a specific deep socket wrench size to remove the plugs
i have no idea what your car use because you did not give the brand
there are 3 sizes of plugs in common use 10,14,&18 mm with 5/8 and 13/16 hexagon. the tool to remove your wheel usually will fit your plug
(the one that came with the car)

Aug 16, 2014 | Cars & Trucks

2 Answers

Spark plug firing order

Hello Harvey, My information shows firing order of 123456. #1 being passenger's front cylinder and #2 being driver's front cylinder.

Jul 30, 2014 | 1995 Isuzu Rodeo

1 Answer

Need to remove brake rotor from tire axle on a 2 wheel drive 3.9 v6 88 dakota drivers side

Do both of them. Remove the tires. Pry the caliper assembly to loosen the disc pads. Unbolt the caliper and pull it with the pads off of the rotor. Remove the wheel bearing cap. Extract the cotter pin and take of the wheel bearings and rotor.

Mar 15, 2011 | Dodge Dakota Cars & Trucks

1 Answer

Got 235/75R15 tires on rear. whats the smaller size tires could go on front.

Don't know if you have 2 wheel drive, or 4 wheel drive...if 4 wheel drive Ford would only recom/mend the same size for the front...with 2 whell drive you can run a smaller front size tire...but don;t know why you would except for looks...:) The size smaller than the 235/75/R15 is 225/75R15 and next smaller is 215/75R15 and so on... A lower profile size would be 235/70R15 or 225/70R15 and so on...I would not recommend using anything smaller than these...the smaller sizes don't always cost less anymore...

Nov 19, 2010 | 1991 Ford Explorer

1 Answer

Oil filter location

The V6 has a screw on filter unlike the 4 cylinder which has a cartridge filter. The filter is located in one of 2 positions depending on which V6 you have. On one V6 it is located under the car towards the front where there is a splash guard that is held in place by two thumb screws. Remove the thumb screws take out the splash guard and there it is. On the other V6 it is located under the air tube that comes from the air filter where you will see a nut about the size 3/4 or bigger just unscrew it and change your oil filter.

May 01, 2010 | 2002 Pontiac Grand Am

1 Answer

Cant get the rotor off of a 99 , any suggestions

Remove the brake caliper, and caliper holder if it goes over the rotor. If it's 2 wheel drive, remove the center cap, take out the cotter pin. Remove the nut holding on the rotor. If it's 4 wheel drive, once you remove the associated brake parts, spray some WD-40 around the studs and the center of the rotor, try striking the rotor with a rubber hammer. Often the rotor will rust to the hub, on the 4 wheel drives. The 2 wheel drives, have the rotor with the hub for the bearings together, the 4 wheel drive has a "top hat" type rotor.

Mar 10, 2010 | 1999 Dodge Ram

1 Answer

Replace front rotors on 2002 4 wheel drive

I am not an expert but yes i beleive you have to remove hub nut to get rotor off,also will need flat head screwdriver to unscrew internal nut before bearing.I also changed bearings while i had it all loose.

Aug 03, 2009 | Mitsubishi Montero Sport Cars & Trucks

1 Answer

Remove the front disc rotor

The rotor and hub assembly are held together by the studs,you must first remove the 4-wheel drive hub assembly,then the wheel bearing nuts,and pull the hub and rotor off as a unit. Next lay it(back down) on a piece of wood, using a drift punch drive the studs out. Turn it over ,lay it(face down) on a block of wood, line the new stud splines up with the grooves in the hub and drive them in with the punch and reassemble. A set of dentist style picks will be helpful with the clip in the 4wd hub and a 4 lug 4wd nut wrench will be needed.

Dec 26, 2008 | 1979 Chevrolet C/K 3500

Not finding what you are looking for?
2002 Hyundai Santa Fe Logo

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts


Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides