Question about 2000 Cadillac DeVille

1 Answer

Need to know which wire attaches to the top and which one goes on the bottom. rear passanager brake abs attachment has broken off and need to temp fix.

Attachment broke off and two wires are just hanging need to know which one goes where white on top and black on bottom or does it matter?

Posted by Anonymous on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 229 Answers

An ohm meter may help or hold the broken pieces together, exactly as it broke, the two pieces should line up to original position and give you an idea.
Hope either helps!

Posted on Apr 17, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 173 Answers

SOURCE: i need the radio wiring diagram for a 1992 cadillac eldorado

white is front left. greay is front right. green is rear left . purple is rear right. black is ground .yellow is power. red is ignition. or do u need factory wiring? the12volt.com try this website it is very helpfull

Posted on Mar 25, 2010

  • 50 Answers

SOURCE: attaching the wires to the starter, what wire goes

should be one big one. that is main. then a smaller plug type that plugs onto the + side of the starter solenoid. that goes to the key for starting. all other i dont know sry, but with those two connected right the car will start provided there is nothing else damaged or broken

Posted on Sep 02, 2010

  • 11 Answers

SOURCE: ABS light is on and

sensor on your brakes

Posted on Oct 06, 2010

  • 8 Answers

SOURCE: i have a 1986 cadillac fleetwood brougham and a

it doese attach to the coolant ive fix one before

Posted on Dec 23, 2010

  • 4 Answers

SOURCE: The clip that attaches the

i would go to a salvage yard to get that,it would definitly be the cheapest and would only take 15 mins to take off.

Posted on Mar 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 chevy trailblazer brake and abs light stays


on my old 1996 blazer.. the little wire coming from the battery +
positive terminal goes to the ABS.
...this needs to be attached properly.
with some snowPlow setups. its a good idea to disconnect the ABS...so the truck will Stop.
....proper bleeding of the ABS brake circuit may be needed.
..best idea.........see GM dealer.

Oct 19, 2014 | 2004 Chevrolet TrailBlazer

1 Answer

Prius warning lights abs pressure brake


abs concern. abs light. also, red brake light. is this correct? drive axle was replaced. testing for abs codes can lead to a pinpoint test.
once codes are read, there may be a specific area indicated to run tests. since the wheel hub area was where the recent work was performed...i suggest looking at the abs exciter ring for the wheel speed sensor.if the teeth are broken off , and or smashed or flattened. the hub, or the ring attached may need correction. there may also be a speed sensor wire and sensor concern after working in that area. inspect the sensor, its wires, and the connectors that attach it to the wiring. take the result of the code check, pinpoint test, and physical condition of the parts into mind, and decide. report your findings. you will need a good quality DVOM test meter to perform electrical tests. and guided diagnostic from the applicable service manual.

Apr 03, 2014 | 2006 Toyota Prius

1 Answer

F-250 06 4x4 diesel, rear brakes dragging (abs light is on)


You need to take off the tire and check to see if the brakes or on properly. They should be sitting right on top of the disk. And if it is not there are 2 screws you have to take off the get the brakes off and reattach the brakes. And some times the brakes are not attached properly or the thing that hold them is broken you can easily tell what is causing the problem when you take off the tire and jack up the truck

Aug 14, 2013 | 2003 Ford F150 Regular Cab

1 Answer

No turn signals, 1 driver brake light bad, ABS light on. 2002/2003 CVPI


Sounds like you have 'ground' issues. Apply the brakes using a broom stick or more apropriate tool so that the brake lights are activated. Then go to the brake light that is not bright enough. using a test-light with a sharp pointed probe, poke the ground wire close to the bulb (usually a black wire) make sure the test light is attached to a grounded bolt. if the brake light gets brighter with ground added, you need a new ground wire. Splice it in to the existing wire & attach it to a bolt. Lights should work better with proper ground. (each bulb has a positive post & neg. post, don't add ground to the side with power coming through it from Battery (+)(red light on test light) - probe wires FIRST with test light to find (+) POS. Hot wire, and leave that one alone.

Aug 09, 2012 | 2003 Ford Crown Victoria

1 Answer

Replace rear brake light.


Open rear hatch. You'll see 2 black screws on the brake light assembly. Remove these 2 screws and pull the assembly out. There, you'll see wires attached to a long grey strip which holds the bulbs. There are 2 screws on each side of the top and bottom of this strip. Remove these and this plastic strip will pull straight out with the bulbs attached to it. You now have access to all 3 bulbs to replace with new ones.

Feb 04, 2011 | 2004 Chevrolet TrailBlazer

2 Answers

Broken wires on left side break caliper


These are either Brake Pad wear sensor or Anti Lock Brake Wires.

Anti Lock ABS system will be inop' if ABS wires broken.

ABS Lamp will be on too.

Jan 14, 2011 | 2000 Volkswagen Beetle

1 Answer

Need to know the torque specs for a rear wheel bearing on a 1999 monte carlo?


Hub & Bearing 3.8L engine Removal & Installation To Remove:
Hub and bearing assembly mounting 88008g39.gif

All W-body cars are equipped with sealed hub and bearing assemblies. The hub and bearing assemblies are not serviceable. If the assembly is damaged, the complete unit must be replaced.
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle with jackstands.
  3. Remove the rear wheel and tire assembly.
  4. If equipped with rear disc brakes, remove the caliper, bracket and rotor.
  5. If equipped with rear drum brakes, remove the brake hose bracket and drum.
  6. If equipped, detach the ABS electrical harness.
  7. Unfasten the four hub/bearing-to-knuckle attaching bolts, then remove the hub/bearing assembly.
To Install:
  1. Install the hub/bearing assembly onto the knuckle. Install the four attaching bolts and tighten to 52 ft. lbs. (70 Nm).
  2. If equipped attach the ABS electrical harness.
  3. Install the rotor, caliper and bracket or drum and bracket, as applicable.
  4. Install the wheel and tire assembly.
  5. Carefully lower the vehicle.
  6. Connect the negative battery cable.

Jul 15, 2010 | 1999 Chevrolet Monte Carlo

1 Answer

Rear abs antilock brakes. Have replaced front


if you have rear abs then yes. you may have pinched the cabl attached to the wheel bearing

Jun 16, 2009 | 2002 Buick Rendezvous

2 Answers

1999 f150 anti lock brakes


John, My 99 F150 had an abs light on and I found the right side front wheel sensor wire had fallen off of the inner fender mount and burned the insulation and grounded the wires together, I taped up the wires and tied it up and the light went out. Your ABS module is located directly beneath your air cleaner next to and just above the steering gear box. It is black plastic and silver alumnium. Says Kelsey-Hayes right on and has six brake lines attached to it. As for the rear brake take that drum off again and have someone help by pushing the brake pedal down while the drum is off press lightly and very slowly, verify that the brake cylinder is moving, do not push hard and fast as it will probably blow the pistons out of the cylinder! If is is frozen replace it and bleed and it should be fine. The brake light is probably on for low fluid. Let me know how it goes.

May 22, 2009 | 1999 Ford F150 Regular Cab

2 Answers

2001 A6 brake light & ESP light


Sounds like you have blown the fuse to this circuit.
Check you were supplied the correct bulb and replace fuse.

Jan 13, 2009 | 2002 Audi A6

Not finding what you are looking for?
2000 Cadillac DeVille Logo

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...