Question about 1998 Ford Windstar

1 Answer

Where is the oil sending unit located on a 3.8

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 79 Answers

Above the oil filter

Posted on Apr 15, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Change oil sending unit 04 tahoe


It is located on rear of engine back by the distributor use to be. see attached pic
25576498-orvua4poo00lqzajd5seke1u-5-0.gif

Mar 15, 2015 | 2004 Chevrolet Tahoe

2 Answers

What is the sending unit and were is it located on my Chevy camaro 3.8 v6 1998


you will have several sending units.
1. Oil pressure sending unit, which according to peoples site that I have visited is right above the oil filter.
2.sending unit in gas tank going to gauges, which is in the gas tank.
3. temperature sending unit, which is located near the thermostat housing or near the end of the upper radiator hose.

Feb 05, 2015 | Cars & Trucks

1 Answer

I have lost about 3 quarts of oil and its not coming from the filter or the oil pan could it be the oil sending unit and where is it located


Yes it is very possible to leak oil from the sending unit. there is several locations depending on the engine size. Leaking as much as you are it should not be hard to find it.

Oct 02, 2014 | 2003 Cadillac CTS

1 Answer

I need to replace the oil sender switch on my 2002 Buick La Sabre


first need to buy oil pressure sending unit 3/8 deep socket remove oil pressure sending unit you need teflon tap sealer for oil sending unit threads.okay to replace oil pressure sending unit.you need safe raise support vechicle locate oil pressure sending unit next to the oil filter.disconnect oil pressure sending unit wire connector then use oil pressure sending unit 3/8 socket remove the sending unit.then take new oil pressure sending unit use teflon tape white plumbers tape or use thread sealer apply to the oil pressure sending unit threads then install new oil pressure sending unit and reconnect electrical connector to sending unit.then crank engine check for oil leak if all is good lower vechicle back to ground wait several minutes check engine oil level.you good to roll.

Feb 09, 2013 | 2002 Buick LeSabre

1 Answer

Where exactly is the Oil Pressure Sending Unit on a Jeep Wrangler 2000 6cyl so i can replace?


Oil Pressure Sensor The 3 wire, solid-state engine oil pressure sensor (sending unit) is located in an engine oil pressure gallery.

Aug 07, 2010 | 2002 Jeep Wrangler

3 Answers

Where is the oil pressure sending unit located?


The pressure sending unit is located on the passenger side rear of the engine just above and slightly to the left of the filter and filter housing.

May 10, 2009 | 2000 Buick LeSabre

3 Answers

Where is the oil sending unit on a 93 chevy silverado 350 engine


the oil sending unit is located at the back of the motor right below the rotor cap it is about 3 inches long and has a 3 wire plug hooked t it

Feb 21, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Pontiac Bonneville(2000) oil pressure sending unit


The oil pressure sending unit is located behind the oil filter, Threaded into an aluminunm housing. It has wiring that plugs into the sending unit. The oil filter has to be removed and you will need a deep well socket and a 6 inch extension. Change the oil and the sending unit together.

Jan 24, 2009 | 2000 Pontiac Bonneville

1 Answer

Location of sending unit on Saab 9-3 turbo convertable


side of engine by firewall passenger side 1/2 way up bock with single wire going to it

Dec 10, 2008 | 2003 Saab 9-3

Not finding what you are looking for?
1998 Ford Windstar Logo

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...