Question about Mitsubishi Cars & Trucks

Open Question

Where's the camshaft sensor located on a 1997 Mitsubishi 3000gt?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
dustyboner
  • 331 Answers

SOURCE: find Mitsubishi 3000GT computer

its under the dash, behind the radio. to get to it, you need to remove the panel on the side of the console.

5a3378a.jpg

Posted on Oct 24, 2008

Ad
savdragon
  • 37 Answers

SOURCE: locate camshaft sensor 2002 chevy trailblazer

Assuming you have a 4.2L engine here is the location.
b3031ef.gif

Hope this helps out,
if so please rate my answers.
Brett

Posted on Mar 19, 2009

  • 114 Answers

SOURCE: Camshaft sensor location

The cam sensor on the 4.7 is located toward the forward edge of the right cylinder head (passenger side). This has a 3 wire connector, tan/with yellow tracer is sensor signal, black / light blue tracer wire is sensor ground and the orange is the 5V supply.

Posted on Mar 22, 2009

dnewcombe1
  • 1564 Answers

SOURCE: where is the camshaft postion sensor located on a

If you mean the Crankshaft position sensor, it is located within the distributor and is quite easily replaced.

Posted on Aug 29, 2009

  • 144 Answers

SOURCE: Where is the camshaft position sensor located in a 2001 VW Passat

when you are looking at the engine pull off the plastic cover on top then the front cover that covers you timing belt there is a wire harness tha goes right to it in the left upper coner two ten mil bolts and it comes off careful not to drop bolts down in belt that could be bad. it is that easy

Posted on Sep 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft postioning sensor on 1997 mitsubishi 3000gt


They are usually located towards the top of the bell housing on the transmission.

Mar 09, 2014 | Mitsubishi 3000GT Cars & Trucks

1 Answer

Where is the cam position sensor located


On a 1992 3000GT, it is located at the end of the valve cover of the rear head at the back of the intake cam. It is just in front of and below where your intake tube meets the throttle body.

Feb 09, 2011 | 1992 Mitsubishi 3000GT

1 Answer

My 1997 Mitsubishi Eclipse wont pass emissions because trouble code P1390. I dont know what this means? Ive researched it everyway I know? My check engine light wont come on at all? Help anyone? Thanks!


This is the direct definition of this code
Mitsubishi DTC P1390 - Timing Belt Skipped 1 Tooth or More.
Probable Causes,
-Timing belt improperly installed
-Camshaft position sensor improperly installed
-Camshaft position sensor connector improperly connected
-Crankshaft position sensor connector improperly connected
-Camshaft's relative position not relearned after one of the following have been serviced: Camshaft, Camshaft sprocket, timing belt tension-er, cylinder head, head gasket, crankshaft sprocket, crankshaft cylinder block or the PCM.

Sounds like something to do with the timing belt it self. You can go to any Autozone or Checker and ask for a code reader (they will let you use it for free) and it will show this code again. You can also reset the cars computer with the code reader to see if it comes back with the same code.

Nov 03, 2010 | 1997 Mitsubishi Eclipse

1 Answer

Where is the IAT sensor location


It is built into the Mass air flow sensor.

Oct 29, 2010 | 1997 Mitsubishi 3000GT

3 Answers

Rebuilt engine. when started again car ticks. timing marks aligned correctly, timing light shows 20 deg. what gives?


Most likely the hydraulic valve lifters, notoriously noisy in Mitsubishi engines. My 2007 Galant Ralliart Mivec 3.8 V6 with less than 15000 miles ticks also as did my 1989 Gallant and 1997 Eclipse.

Nov 16, 2009 | 1995 Mitsubishi 3000GT

1 Answer

Intermittent problem starting car when hot


need another car side by side and swop bits over till you hit whatever is causing the problem,my suggestion is a sensor but what one??

Mar 20, 2009 | 1997 Mitsubishi 3000GT

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...