Question about Cars & Trucks

1 Answer

How do I replace passenger side pop out window in 97 s10 pickup

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,585 Answers

You have to remove the interior trim to access the nuts. to remove the hinges for the old glass. The trim pops off. Be careful, it can break.

Posted on Apr 15, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 97 s10 fule pump stop workin

I would first check you fuel pump relay. Also check the ground wire near you gas tank. Hope that will help

Posted on Jan 14, 2009

  • 10 Answers

SOURCE: how do I remove drivers side door panel on 1998

i think there are screws around the door handle on the in side that need to be taken off the the rest just pop out

Posted on Feb 01, 2010

  • 2002 Answers

SOURCE: rear passenger side pannels

It's called a rear quarter panel and should extend from the rear of the back door to the tailgate and from the window to the bottom of the truck. It should be available from the dealer or most auto parts stores. The dealer will cost more but it will be heavier steel than the aftermarket. Aftermarket ones can normally be bought in sections. You don't necessarily need to buy the whole panel.They should have a book that shows the panels so you can pick what you need.
Use the new panel to mark out your cut marks on the old one. Just remember to cut inside your marks so that you have a lip to fasten the new panel to and fasten the new panel on the inside of the old one. Hope this helps.

Posted on May 30, 2010

HansPP
  • 2510 Answers

SOURCE: i need to replace passenger side rear veiw mirror

To remove the door panel, remove any screws that are in the vicinity of pull handles and door pockets. These screws will be under little trim covers that you need to prise off to get to their heads. Look for the screws around the edge of the panel and also the screw in the latch release handle recess.
The lock knob, if there is one there, will have to be screwed off and then carefully work your way around the door, freeing the panel's clips from their holes in the door frame. (Doot panels are brittle and clip break out easily).
Finally the panel will probably have to be lifted out if the window slot. (If the panel does not come off, work out what is retaining it and remove that screw or slide it off the clip that is still holding the panel. Disconnect any electrical plugs behind the panel. Under the panel you will find a plastic dust sheet that is stuck to the door frame, remove this carefully, you will have to replace it before replacing the panel.

Posted on Apr 27, 2011

ed_dylp
  • 24 Answers

SOURCE: 2003 ram 1500 pickup window

check for continuity across the switch wires. if nothing happens then you know you have a broken wire somewhere. make sure the ignition is to on. good luck

Posted on Jul 29, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a heater core for a 1994 s10 pickup


Remove the glove box.On the passenger side under the hood, remove the two hoses connected to the heater core. remove the connectors/airlines connected to the box, remove the lever on top of the box.remove retaining screws. two screws hold cor in.-----------------------------------------------------------------
Car Diagnostic software

Nov 14, 2012 | Cars & Trucks

1 Answer

Won't stay in 5th gear. Pops out to neutral.


97 s10 pops out of 5th gear when you let off fuel

Mar 08, 2011 | 1997 Chevrolet S-10 Pickup

1 Answer

How do I remove drivers side door panel on 1998 Chevy S10 pickup to repair/replace window regulator?


i think there are screws around the door handle on the in side that need to be taken off the the rest just pop out

Feb 01, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

I have 97 S10 4.3L my fuel gauge doesnt work.


just put a sending unit in it I have done tons of them...

Dec 06, 2009 | 1997 Chevrolet S-10 Pickup

2 Answers

Need a wiring diagram for a chevy s10. brake


your power starts at the brake light fuse,check with a test light,then proceed to stop light switch on brake pedal under dash,one wire will be hot when when you check it with your test light, the other won't be until you press down the brake pedal then the power flows through to the second wire,if no power to second wire replace switch,if you have power remove tail light bulbs and check for power in side socket.

Nov 24, 2009 | 1997 Chevrolet S-10 Pickup

1 Answer

I HAVE A 97 4.3 2WHEEL DRIVE S10 TRUCK. STARTS WHEN IT WANTS


check the coolant sensor, check for possible fuel filter clogged.

Jul 25, 2009 | 1997 Chevrolet S-10 Pickup

2 Answers

Carpet on passenger side gets wet


The drain from the a/c under the dash is plugged up and needs to be cleared. If you check from under the vehicle, u should be able to find the end of the drain tube on the passenger side, behind or near the front wheel. Carefully run a wire up the tube to dislodge the obstruction (goop build up). You can also use compressed air.

Mar 19, 2009 | 1999 Chevrolet S-10 Pickup

2 Answers

Chevy S10 Pickup Starter. Removed the two bolts


Just changed a starter in a 94 S10 4x4. The only way to remove the starter was to take the passenger side exhaust manifold off and bring the starter out that way. Installation the same in reverse. Hope this helps. Don

Mar 14, 2009 | 1998 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...