Question about 1996 Nissan Pickup

2 Answers

What size socket does it take to remove the caliper bolts from a 1996 Nissan D21 pickup?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Nissan Expert
  • 279 Answers

To remove the entire caliper assembly off the strut you will need a 17 mm socket

Posted on Apr 15, 2015

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 35 Answers

I think the bolts are 14mm.

Posted on Apr 14, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove front brake caliper on 1996 mazda 626


if you are just changing the pads there are 2 bolts that split the caliper in halve and allow you to change the pads thres two bolts are located top and bottom on the backside of the caliper and require an allen wrench for removal to remove the whole caliper there are 2 bolts on the back side closer to the center top and bottom that require a 17mm socket remove these 2 bolts clamp off the flex brake hose with a clamp and remove from caliper and work up and down until caliper comes away from disc

Nov 30, 2010 | 1996 Mazda 626

1 Answer

Where can i find a replacement bolt for a 1991 nissan d21 clutch pressure plate


you can get one from nissan, or you could take the bolt to a machine shop and have one made, or the junk yard. thats about the only thing i know of.

Nov 29, 2010 | 1991 Nissan Pickup

1 Answer

What size socket do I need to remove the Nissan oil sending unit?


I think 46
but not sure measur with ruler then buy a socket
other wise use a big adjesterble plyer hold sender unit nut tightly put a big screw drive through the plyer mouth and turn
good luck

May 08, 2010 | 1993 Nissan Pickup

1 Answer

How do i replace the starter on a 1996 nissan pickup?


you hav to do it from underneath.put on jack stands remove battery cables from battTry to remove electrical wires from starter.Get a peice of paper and write down or draw a diagram of the location of wires.Get a ratchet and 12 inch extension witg a 23 mm socket.the lower bolt comes out fairly easy.The top bolt takes a little finessing,go to it up over the top of starter, if you cant get the socket on the bolt good replace the socket with 13mm swivel socket.Replace using same procedure the last thing hooking the batt back up {very important] Good luck.

Apr 27, 2010 | 1996 Nissan Pickup

1 Answer

Need to know what type and size the front caliper bolt is on a 1996 dodge intrepid ,not sure i have the right size tool to remove it.


They're guide pins for the calipar to slide on while braking,as well as bolts. A 10mm deep socket and ratchet should do it. Hope this helps.

Mar 26, 2010 | 1996 Dodge Intrepid

1 Answer

Rear brake pads on 1996 nissan 300zx


It should just be the caliper mounting bolts that bolt the caliper to the hub assembly. If I remember correctly, they're 17mm. There are two of them, and if you feel the caliper, and run your hand down behind the back side of it, you should find one bolt near the top of the caliper body on the hub, and one down below. Once they're removed, the caliper will come off (you may have to wedge a large screwdriver between the top of the caliper and the rotor and lever it off, but it'll come off).

Jul 06, 2008 | 1996 Nissan 300ZX

Not finding what you are looking for?
1996 Nissan Pickup Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...