Question about Cars & Trucks

1 Answer

Rear brake bleeding procedure - Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,272 Answers

To Bleed Air From Brake Lines.

Click the link below For Step by step Procedure:
http://carrepairworld.blogspot.com/2015/04/air-in-brake-lines.html

http://www.allcarhelp.com/2015/04/rear-brake-bleeding-procedure.html

This Will Help You.
Thanks.

Posted on Apr 14, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Brakes went out,master cylinder is dry. filled the master cylinder pumped brakes and bled rear drivers side


    If there is a substantial fluid eruption, there are air bubbles still trapped in the system. You must repeat the bleeding procedure to remove that air. A modest disturbance in the fluid returning to the reservoir indicates a properly bled brakesystem.

    How To: Bleed Your Brakes - Feature - Car and Driver

    www.caranddriver.com/.../how-to-bleed-your-brakes-feature Car and Driver
Feedback

How To: Bleed Your Brakes - Feature - Car and Driver

www.caranddriver.com > Features

Car and DriverIf there is a substantial fluid eruption, there are air bubbles still trapped in the system. You must repeat the bleeding procedure to remove that air. A modest disturbance in the fluid returning to the reservoir indicates a properly bled brake system.

How to Bleed Brakes - Tips on Bleeding Brakes

Jan 01, 2016 | Cars & Trucks

1 Answer

1990 jeep wrangler bleeding breaks


Hi there:
I suggest to check this procedure, when the hydraulic brake system must be bled whenever a fluid line has been disconnected because air gets into the system.

A leak in the system may sometimes be indicated by a spongy brake pedal. Air trapped in the system is compressible and does not permit the pressure applied to the brake pedal to be transmitted solidly through the brakes. The system must be absolutely free from air at all times. If the master cylinder has been overhauled or a new cylinder has been installed, bleed the cylinder on a bench before installation. When bleeding brakes, bleed at the wheel most distant from the master cylinder first, the next most distant second, and so on. During the bleeding operation the master cylinder must be kept at least 3 / 4 full of brake fluid.


The ABS bleeding procedure is different from the conventional method. It consists of the following three steps:
Step 1: Conventional manual brake bleed.
Step 2: Bleeding the system using the DRB scan tool.
Step 3: An additional conventional manual brake bleed.

The recommended ABS bleeding procedure is as follows:
  1. To bleed the brakes, first carefully clean all dirt from around the master cylinder filler cap. Remove the filler cap and fill the master cylinder with DOT 3 brake fluid to the lower edge of the filler neck.
  2. Bleed the master cylinder first. Have a helper operate the brake pedal while bleeding each master cylinder fluid outlet line. Do not allow the master cylinder to to run out of fluid,as this will allow additional air to be drawn into the cylinder.
  3. Bleed the brake system in the following sequence:
    1. Master cylinder
    2. HCU valve body (at fluid lines)
    3. Right rear wheel
    4. Left rear wheel
    5. Right front wheel
    6. Left front wheel
  4. Clean off the bleeder connections at all four wheel cylinders. Attach the bleeder hose to the right rear wheel cylinder bleeder screw and place the end of the tube in a glass jar, submerged in brake fluid.
  5. Open the bleeder valve 1/2 - 3/4 of a turn.
  6. Have an assistant depress the brake pedal slowly and allow it to return. Continue this pumping action to force any air out of the system. When bubbles cease to appear at the end of the bleeder hose, close the bleeder valve and remove the hose.
  7. Check the level of fluid in the master cylinder reservoir and replenish as necessary.
  8. After the bleeding operation at each wheel cylinder has been completed, fill the master cylinder reservoir and replace the filler plug.

Do not reuse the fluid which has been removed from the lines through the bleeding process because it contains air bubbles and dirt.


  1. Perform the "Bleed Brake'' procedure with the DRB II scan tool. This procedure is described in the DRB II software information and diagnostic guide.
    1. Attach the DRB II scan tool to the diagnostic connector.
    2. Run the Bleed Brake procedure as described in the DRB II tester guide.
  2. Repeat the conventional bleeding procedure as previously outlined.
  3. Fill the master cylinder reservoir to the proper level.
  4. Check the brake operation.


Hope this helps.

Apr 21, 2013 | Jeep Wrangler Cars & Trucks

3 Answers

Whats the proper rotation to bleed on py cruiser breaks


You should start on the most far wheel - typically it's rear right wheel, then rear left, then front right and front left.

Oct 15, 2012 | 2006 Chrysler PT Cruiser

2 Answers

I have a 2004 Land cruiser and changed the right rear brake cyl and brake shoes . What is the proper procedure to bleed the rear brake system. Thank you for your help.


  1. Check the fluid level in the reservoir after bleeding each wheel. Add DOT3 fluid, if necessary.
  2. If the master cylinder was disassembled or if the reservoir becomes empty, bleed the air from the master cylinder as follows:
    1. Disconnect the brake lines from the master cylinder.
    2. Slowly depress the brake pedal and hold it.
    3. Block off the outlet plug with your finger, and release the brake pedal.
    4. Repeat 3 or 4 times.

  3. Bleed the brake starting with the one furthest from the reservoir and then the next furthest, etc.
  4. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down.
  5. At the point when fluid stops coming out, tighten the bleeder plug to 11 Nm (8 ft. lbs.), then release the brake pedal.
  6. Repeat until all the air in the fluid has been bled out.
  7. Repeat the procedure to bleed the air out of brake line for each wheel.
  8. Check the fluid level and add DOT3 fluid if necessary.

Aug 07, 2011 | 2004 Toyota Land Cruiser

1 Answer

How to bleed brakes on 1997 Saturn


The brake system bleeding procedure differs for ABS and non-ABS vehicles. The following procedure pertains only to non-ABS vehicles. For details on bleeding ABS equipped vehicles, refer to the ABS procedures later in this section.

WARNING Make sure the master cylinder contains clean DOT 3 brake fluid at all times during the procedure.
  1. The master cylinder must be bled first if it is suspected of containing air. Bleed the master cylinder as follows:
    1. Position a container under the master cylinder to catch the brake fluid.
    2. Loosen the left front brake line (front upper port) at the master cylinder and allow the fluid to flow from the front port.
    3. Connect the line and tighten to 24 ft. lbs. (32 Nm).
    4. Have an assistant depress the brake pedal slowly one time and hold it down, while you loosen the front line to expel air from the master cylinder. Tighten the line, then release the brake pedal. Repeat until all air is removed from the master cylinder.
    5. Tighten the brake line to 24 ft. lbs. (32 Nm) when finished.
    6. Repeat these steps for the right front brake line (rear upper port) at the master cylinder.
WARNING Do not allow brake fluid to spill on or come in contact with the vehicle' finish, as it will remove the paint. In case of a spill, immediately flush the area with water.
  1. If a single line or fitting was the only hydraulic line disconnected, then only the caliper(s) or wheel cylinder(s) affected by that line must be bled. If the master cylinder required bleeding, then all calipers and wheel cylinders must be bled in the proper sequence:
    1. Right rear
    2. Left front
    3. Left rear
    4. Right front
  2. Bleed the individual calipers or wheel cylinders as follows:
    1. Place a suitable wrench over the bleeder screw and attach a clear plastic hose over the screw end.
    2. Submerge the other end in a transparent container of brake fluid.
    3. Loosen the bleed screw, then have an assistant apply the brake pedal slowly and hold it down. Close the bleed screw, then release the brake pedal. Repeat the sequence until all air is expelled from the caliper or cylinder.
    4. When finished, tighten the bleed screw to 97 inch lbs. (11 Nm) for the front, or 66 inch lbs. (7.5 Nm) for the rear.
  3. Check the pedal for a hard feeling with the engine not running. If the pedal is soft, repeat the bleeding procedure until a firm pedal is obtained.
zjlimited_349.jpg

Fig. 1: Loosen the front brake line in order to bleed the master cylinder

zjlimited_350.jpg

Fig. 2: Connect a bleed hose from the bleed valve on the front caliper to a jar of brake fluid

zjlimited_351.jpg

Fig. 3: Always follow the lettered sequence when bleeding the hydraulic brake system





Hope this helps to solve it; remember to rate this answer.

Dec 29, 2010 | 1997 Saturn SL

2 Answers

Replaced brake line, rotors and pads bled brakes all around and the brakes when the truck is off work but once i start the truck the brake pedal goes to the floor and have no brakes at...


Bench Bleed the M/C first, then do not let it run dry during system bleeding. Parts stores sell a kit that helps installed m/c bleeding.

Sep 29, 2010 | 2001 GMC Jimmy

3 Answers

Whats the procedure for bleeding brakes 2000 grand marquis


Bleed the master cylinder at the brake lines,then bleed right rear ,left rear,right front,and left front.

Jun 12, 2010 | 1998 Mercury Grand Marquis

5 Answers

Is there a bleeding sequence for a 1990 Toyota Four Runner? We replaced one front driver side brake line and both calipers and we cannot seem to get it to bleed properly. Thanks


normally, the brakes are bled starting from the furthest brake to the closest with respect to the master brake cylinder. the sequence is : right rear, left rear, right front, left front. pump the brakes until pressure is built up. do this rather slowly. while keeping downward pressure on the pedal, open the bleed screw slowly. the pedal will go to the floor. hold the pedal on the floor and tighten the bleed screw. do this until no air is observed. keep the reservoir. repeat with the rest of the brakes following in sequence

http://www.aa1car.com/library/2003/bf90347.htm

May 31, 2010 | 1990 Toyota 4Runner

1 Answer

What is the correct procedure in bleeding the brake system on a 1999 Tahoe? Is there a special procedure for the ABS portion?


All brake syastems are the same whether single, cross or dual, start with filling the res. start with the cylinder furtherest away from res and work towards the nearest, so if the res in on the front left in the engine bay, start rear right, rear left, front right, and finaly front left, keep an eye on the res level at all times anmd never release pedal pressure untill the bleed nipple is tight, I use a one way bleed tube and a jar, makes it easy one man job as air can't get back in, so open, pump 3 or 5 times and tighten.

Jul 09, 2009 | 1999 Chevrolet Tahoe

1 Answer

Brake pad replacement


You will need to bleed all four corners, starting at the right rear, then left rear, then right front, then left front. Your bleed procedure always goes from the wheel farthest from the master cylinder, to the closest. By bleeding only the rear brakes, you've gotten air out back there, but not necessarily any air that might have moved farther forward. Bleed your rears again, and then move forward to bleed the fronts, and see if that helps.

Aug 31, 2008 | 2003 Audi A4 Cabriolet

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...