Question about 1994 Buick LeSabre

Open Question

How to replace belt tension device on 94 Buick le sabre

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
greg_margo
  • 1959 Answers

SOURCE: procedure to repaloce rear shocks

Removal & Installation

  1. Remove the tire and wheel assembly.
  2. Support the control arm with a jack stand.
  3. Remove or disconnect the following:
  4. Electronic Ride Control (ELC) air tube from the shock
  5. Two bolts securing the shock to the control arm
  6. Trunk trim to gain access to the shock upper mounting nuts.
  7. Cover, the two nuts, and the reinforcement from the top of the shock
  8. Shock from the vehicle
01ccab9.gif

Here are links to more diagrams. Best of luck on your repair.
Greg


http://www.chiltonlibrary.com/content/images/7922/images/7922UG21.pdf

http://www.chiltonlibrary.com/content/images/7922/images/7922UG22.pdf

Posted on May 20, 2009

Ad
honeymokey
  • 3113 Answers

SOURCE: 1991 Buick Regal 3.8L Belt Tensioner

Remove belt and unbolt center pulley bolt. I believe it's a backward theaded bolt. Turn to the right to loosen.

Posted on Jun 17, 2009

  • 6 Answers

SOURCE: how do I replace my fuel level sensor on a 2000

Access via trunk, remove carpet and find inspection cover, remove to access fuel level sending unit which is attached to the fuel pump.

Posted on Oct 21, 2009

  • 16 Answers

SOURCE: i need a fuse box diagram

http://www.wiringdiagrams21.com/2009/07/13/1993-buick-lesabre-fuse-relay-and-circuit-breakers

Posted on Nov 24, 2009

tecnovative
  • 360 Answers

SOURCE: how to replace left front

Headlight Removal & Installation Bulb Replacement CAUTION
Improper handling of a halogen bulb could cause the bulb to shatter into flying glass fragments due to the bulbs containing gas under pressure. Always wear eye protection, only handle the bulb by its base, keep dirt and moisture off the bulb, do not install the bulb with power at the socket, and keep them away from children.

To Remove:

  1. Turn off power to the headlamps.
  2. Remove the headlamp assembly.
  3. Turn the bulb socket counterclockwise and remove from the headlamp assembly.
  4. Remove the bulb from the socket.
To Install:
NOTE: If oil from your skin or anything damp comes in contact with the bulb, clean the bulb with alcohol or a suitable degreaser and wipe the bulb dry. Too prevent the bulb from exploding when the bulb is turned on.
  1. Install the bulb into the socket.
  2. Install the bulb into the headlamp assembly and turn clockwise to lock into place.
  3. Install the headlamp assembly.
Headlight Assembly To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Open the hood.
  3. Remove the fasteners (D) that retain the headlamp assembly (C) to the headlamp bracket (A).
  4. Pull the headlamp assembly (C) forward in order to disengage the rear retaining pin (B), and disconnect the electrical connector from the forward lamp harness.
  5. Remove the headlamp assembly from the vehicle. NOTE: Avoid touching the bulb or letting the bulb come in contact with anything damp. Oil from your skin or moisture on the bulb can cause the bulb to explode when the bulb is turned on. If either comes in contact with the bulb, clean the bulb with alcohol or a suitable degreaser and wipe the bulb dry.
  6. Remove the bulbs from the headlamp assembly by turning them counterclockwise.
To Install:
  1. Install the bulbs into the headlamp assembly and turn them clockwise to lock in place.
  2. Connect the electrical connector to the forward lamp harness.
  3. Install the headlamp assembly (C) into the vehicle by pushing rearward in order to engage the rear retaining pin (B).
  4. Install the fasteners (D) that retain the headlamp assembly (C) to the headlamp bracket (A).
  5. Close the hood.
  6. tecnovative_74.gif

Posted on Jan 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

95 buick le sabre has clicking noise when started, but noise disappears upon acceleration


Check your oil level in your engine, may have a valve tappet. check your fan/ timing belts for damage. Add & or replace if needed.

May 27, 2014 | 1995 Buick LeSabre

2 Answers

How do you remove the pulley off of the tensioner on a Buick Le Sabre


That is the right way, spray the bolt with some wd40 or liquid wrench.

Oct 13, 2017 | 1997 Buick LeSabre

1 Answer

My horn quit working on my 94 Buick Le Sabre. i replaced the horn but still no sound. i cant figure out what relay is the horn


Hello: Remove the cover on the fuse box, on the inside there should be a key to follow. also check the fuse box under the dash for the same.

Jan 14, 2011 | 1994 Buick LeSabre

1 Answer

HOW DO I TIGHTEN THE LOOSE BELT AFTER INSTALLATION ON 97 BUICK LE SABRE? REALLY NEED A DIAGRAM TO MAKE SURE I INSTALLED THE SERPENTINE BELT CORRECTLY.


There may be a diagram imprinted on fan shroud. There is a belt tensioner that tightens the belt. Also when installing belt be sure you have grooved part of belt riding on grooved pulleys. And flat side of belt riding on flat sided pulleys.

Sep 13, 2010 | 1997 Buick LeSabre

2 Answers

Serpentine belt diagram for 2003 buick le sabre


Since there is NO sticker under the hood of this 2003 Buick LeSabre and it is not in the owner's manual, a Google search revealed that it is the same as at http://www.fixya.com/cars/t3438653-change_serpentine_belt_1998_buick

8_1_2012_4_17_57_pm.jpg

Jul 11, 2010 | 2003 Buick LeSabre

1 Answer

1993 buick le sabre 3.8v6.no spark somthing shorted out


those wires are probably going down to the crank sensor if that sensor fails then the car will not start so fix the wiring and try replacing the crank sensor.

Nov 07, 2009 | 1992 Buick LeSabre

2 Answers

93 buick le sabre transmission slipping


fluid low and possibily need of replaceing try this first. hope this helps?

Aug 25, 2009 | 1993 Buick LeSabre

2 Answers

Howq do I remove serpentine belt on my 1999 buick La saber


Find the tensioner it will be a pulley that does nothing but put tension on the belt. There should be a square hole in it. that should fit a 3/8 inch drive socket wrench or breaker bar. Use that to remove the tension from the belt and remove - do the same to install new belt

Aug 18, 2009 | 1992 Buick LeSabre

Not finding what you are looking for?
1994 Buick LeSabre Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...