Question about Cars & Trucks

1 Answer

Check engine code connector - Cars & Trucks

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 531 Answers

If it's a vehicle past 1996, your obd2 connector is under the steering wheel

Posted on Apr 14, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can a diagnostic connector on 1995 Toyota 4 runner be jumped over with jumper wire to get check engine codes?


There is probably a way to access codes by using a jumper and causing the engine checklight or an integral led to flash in groups. I can't say which pin or pins need jumping.

I suggest you ask the question of google and click on the youtube video.

Jun 26, 2016 | 1995 Toyota 4Runner

1 Answer

P0501 code?


P0501 - Vehicle Speed Sensor (G22): Implausible Signal Possible Causes
  • Wiring/Connectors from/to Vehicle Speed Sensor (G22) faulty
  • Wiring/Connectors from Transmission Control Module (J217) to Engine Control Module faulty
  • Vehicle Speed Sensor (G22) faulty
  • Malfunctioning Left Front wheel speed sensor (in vehicles that don't use a physical G22 sensor)
Possible Solutions
  • Check Wiring/Connectors from/to Vehicle Speed Sensor (G22)
  • Check Wiring/Connectors from Transmission Control Module (J217) to Engine Control Module
  • Check Vehicle Speed Sensor (G22)
  • Check ABS Brakes for faults and diagnose malfunctioning Left Front wheel speed sensor if applicable

Category:

Mar 10, 2016 | 1996 Audi A4

1 Answer

Where is the obd2 connector location on holden ra rodeo v6


isuzimpuls.gif
Connect white (test lead) and black (ground lead) wires that are branched from harness approximately eight inches from ECM. After leads are grounded, the "Check Engine" light will flash the diagnostic trouble codes. The DTC's are indicated by the flashing CEL.
FLASH, FLASH, pause, FLASH, FLASH, FLASH = Code 23.
If only one diagnostic trouble code is stored, the DTC will repeat continuously until test leads are disconnected. If more than one diagnostic trouble code is stored, each DTC will repeat three times, starting with the lowest, then proceed to the next DTC. After all DTC's have been displayed, the pattern will repeat.I-MARK 84-85
Connect male and female test leads taped into wire harness near ECM. After leads are connected, the "Check Engine" lamp will flash the trouble codes. The DTC's are indicated by the flashing CEL.
FLASH, FLASH, pause, FLASH, FLASH, FLASH = Code 23.
If only one diagnostic trouble code is stored, the DTC will repeat continuously until test leads are disconnected. If more than one diagnostic trouble code is stored, each DTC will repeat three times, starting with the lowest, then proceed to the next DTC. After all DTC's have been displayed, the pattern will repeat.
86-87 Impulse located near the ECM connector, is used to actuate the Engine Control Module (ECM) trouble code memory within the module. Two terminals (A and C) of this connector are used to activate the diagnostic trouble code system in the ECM. With the ignition switch turned On, engine Off, connect a jumper wire between terminals A and C. The "Check Engine" lamp will begin by flashing a DTC 12. DTC 12 = flash, pause, flash, flash. There will be a longer pause and a code 12 will repeat two more times. This code indicates the self-diagnostic system is operating. The cycle will then repeat until the engine is started or the ignition is switched Off. In most cases, DTC's will be checked with the engine running since no DTC's other than DTC 12 or 51 will be present without the engine running. Remove jumper wire from ALDL connector before starting engine. Reconnect jumper wire after engine is running.

Throttle Body Fuel Injection

The ECM test connection is located under the center console.
A built-in, self diagnostic system will identify problems in the throttle body fuel injection system. When a problem is detected, the diagnostic system will illuminate the "Check Engine" light.
When the engine is started, the Check Engine light should turn off.. If the light remains lit, the self diagnostic has detected a problem. To determine where the problem exists, ground the "Test" terminal of the connector with the ignition On, engine Off and watch the check engine light. Each DTC will flash three times (lowest to highest).

Aug 21, 2014 | Holden Rodeo Cars & Trucks

1 Answer

I have a 95 buick le saber 3.8 ltr. It back fires when running. But when check engine light is on it wont back fire. It does sound louder with check engine light on. Changed coils. I need help trying to...


You need to scan the computer for trouble codes. If the light was on, there must be codes set. On a '95 Buick, it would be OBD-1, On Board Diagnostics-first generation ('96 and later is all OBD-2).
The diagnostic connectors are different for OBD1 and OBD2, but in '94 and '95, GM was on some models using a "hybrid" diagnostic link connector. You will just have to find the right diagnostic connector to get your codes. The guys at autozone or a national parts store who do engine scans for free may help you figure it out. If it is a straight forward OBD 1 connector, a cheap code reader could scan for trouble codes. For the OBD1, you can also use a jumper wire between terminals
A & B of the diagnostic link connector. Turn key to on, and two digit codes will begin to flash on the check engine light. Code 12, for instance, would be a flash, pause, two short flashes, and longer pause before the next code appears. Code 12 by the way, just means that the computer is in diagnostic mode-after that any set codes will appear or be flashed. Code 55 may also be flashed-this code means the end of codes that are set.

Sep 06, 2013 | 1994 Buick LeSabre

1 Answer

Diagram


All Toyota vehicles with electronic fuel injection utilize the Toyota EFI or TCCS engine management system. This system incorporates many features to enhance performance, emissions, and drivability. One feature is the Self Diagnostic System. The self diagnostic system monitors engine operations and when a particular sensor or input varies out of specified operating parmeters, the "Check Engine" will be illuminated.
READING THE TROUBLE CODES
Reading the diagnostic trouble codes is very easy. You will need a paper clip or auto wire to short the check connectors of the diagnostic connector. The diagnostic connector comes in two types. The early system is located on the inner-left fender well and is a round, green connector, usually located near the air cleaner. Simply jump the two terminals in this connector with the ignition switch in the "ON" position and the engine off. Later models, '87 and newer use a multiple terminal "DIAGNOSTIC" connector which is a small, rectangular-shaped grey "box", usually located near the right fender in the enigne compartment. To get codes out of this type of connector, jump the "TE1" and "E1" teminals. Finding these terminals is easy as the inside cover of the diagnostic connector contains a schematic of the connector pinouts. If the underhood emission decal (VECI) is still intact on your vehicle, the proper pins for this are outlined there as well.
The trouble codes will appear as flashes of the check engine lamp. Be sure the ignition key is on, the engine off, and your foot off of the accelerator when reading the codes. Two different codes may appear: One-digit and two digit. One digit codes have an approximate 4.5 second delay between flashes with the check engine light illuminating for about a half of a second. Mulitiple codes have a 2.5 second delay between them. For example a code two flashes the check engine lamp two times in a little over one second: I I. If two codes are stored, such as a code two and a code four, the lamp may flash as such: ....I I....I I I I. Crude examples but you get the idea. Two digit codes are similar but will flash the lamp with the first number first and the second number last. An example of a code twleve is I ....II and a code twenty four is I I..IIII.

Jul 29, 2013 | 1994 Toyota Corolla

2 Answers

Where is diagnostic port on a 1991 mazda 929


It hasnt got a OBDII but i seem to remember a special plug under the bonnet ,then i gave up and changed a vacumn pipe to a sensor and it run like a dream

Dec 19, 2012 | Mazda Cars & Trucks

2 Answers

I bought a 1998 mitsubishi eclipse and the check engine light came on we hooked up the machine to diagnos it and we got 2 codes po700 and p1784 . we are wondering what the codes mean and how to fix the...


DTC 1784: LOW-REVERSE PRESSURE SWITCH
1.Remove transaxle relay from connector. Turn ignition on. Install scan tool and observe low-reverse pressure switch condition. Apply battery voltage to transaxle relay connector terminal No. 8. If low-reverse pressure switch stays off, go to next step. If low-reverse pressure switch turns on, go to step 4 .

2.Raise vehicle enough to allow drive wheels to spin freely. Test low-reverse clutch hydraulic pressure. See HYDRAULIC PRESSURE TESTS under TESTING. If low-reverse clutch pressure test is not within specification, internal transaxle failure exists. If low-reverse clutch pressure test is within specification, observe scan tool.

3.If low-reverse pressure switch turns on, trouble code is intermittent. Check wire harnesses and connectors for damage or poor connection. If low-reverse pressure switch does not turn on, replace solenoid and pressure switch assembly. Recheck trouble codes. If trouble code resets, replace TCM.

4.Check and repair wiring harness between transaxle relay connector and solenoid and pressure switch assembly connector. If wiring harness is okay, check wire between TCM connector terminal No. 10 and solenoid and pressure switch assembly.

5.If wire between TCM connector terminal No. 10 and solenoid and pressure switch assembly is okay, check TCM and solenoid and pressure switch assembly connectors. Repair connectors as necessary. If connectors are okay, recheck trouble codes. If trouble code resets, replace solenoid and pressure switch assembly. Recheck trouble codes. If trouble code resets, replace TCM.

P0700-The Transmission Control Module (TCM) monitors the malfunction of sensors and actuators relating to transmission control. When the TCM detects a malfunction with the control, a signal is send to the Engine Control Module (ECM) to trigger the Engine Light or Service Engine Soon light. The ECM stores the P0700 code and it means the TCM detected a malfunction with the transmission controls.

I would try disconnecting he battery and letting it sit for 5 minutes, then hook it back up to see if they return-the 700 code is probably related to the 1784 code, that seems to be your main issue.

Jun 06, 2011 | 1998 Mitsubishi Eclipse

1 Answer

Pulling check engine codes on 1984 el camino


Locate your aldl connector under dash near steering column. It should have 12 pin connector. Older cars had 8 pin connector. You can do either one. On 12 pin connector jump the last 2 pins, on top row, in connector with paperclip or wire. Turn on ignition till check engine light turns on. Count & write down how many times it flashes. It will flash for example 3 times stop then 1 time = 31 code. In older 8 pin connector jump the 2nd & 4th pins on top.

Jun 15, 2010 | 1984 Chevrolet El Camino

1 Answer

How do I see/get error codes for my 1988 4Runner? (idling prob.)


The check connector is located near the No. 2 relay box. Short terminals T and E1 of the check connector. (jump together)
2. Turn the ignition ON. do not start engine.
3. Read codes by the number of flashes of the "CHECK ENGINE" WARNING LIGHT.
4. System normal: blink every 0.25 seconds.
5. Malfuction Code: light will blink a number of times equal to the malfuction code.Between first digit and second digit, 1.5 sec
Between code and code 2.5 sec, between all malfuction codes 4.5 sec
6. The diagnostics code series will be repeated as long as the connector terminals T and E1 are jumped.
7. Codes are 2 digit numbers

Feb 11, 2010 | 1988 Toyota 4Runner

1 Answer

How to retrieve trouble codes on 91 loyale wagon


mil is the malfunstion indicator lamp (check engine light) there is a connector either under the dash or under the hood near firewall that is normally not plugged in to anything. Use a paperclip to jumper this and the engine light will flash codes. i think the connector is green but check a repair manual to be sure. there are other connectors that you don't want to mess with by accident

Oct 16, 2008 | 1991 Subaru Loyale

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...