Question about 2007 Hyundai Atos Prime

Open Question

What would be the torque to use in order to tighten the bearings on the crank

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's the torque settings for the Opel corsa1.4i crank mains and big ends


Please note: You must use new bolts as these are torque to yield bolts, in other words they are a type of linear spring.
Connecting rods/big-end bearing cap bolts (use new bolts)
stage 1 ... 25 Nm (18 lb ft)
stage 2 ... angle tighten + 30 degrees
Main bearing cap bolts (use new bolts)
stage 1 ... 50 Nm (37 lb ft)
stage 2 ... angle tighten + 45 degrees
stage 3 ... angle tighten + 15 degrees

Nov 22, 2016 | Opel Corsa Cars & Trucks

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

Hi what is the crank and conrond torque settings for a nissan RB30et and what the ring gap set that


Crank shaft main bearings.46-52 Nm tighten in 2 or three stages.
Con rod bearings 14-16 Nm1st step. 2nd step 39-45. Or if you have access to angle torque 60-65 degrees. Rule of thumb ring gap is .005" per inch of bore. eg 3" bore .015" ( thou of inch)

Nov 24, 2012 | Cars & Trucks

1 Answer

Hi im fixing a 89 honda civic have everything to put it back together but the torque settings for mains,connector rod bearings head stage 1,2,3 an the rest thanks


CRANK SHAFT PULLEY BOLT TORQUE IS 83 FT LBS. MAIN BEARINGS TORQUE IS 48 FT LBS ROD BEARINGS TORQUE 23 FT LBS. YOU NEED A BEARING SEQUENCE GET PIECE OF PAPER WRITE NUMBERS 9 5 1 3 7 AND UNDER THIS NUMBER LINE NUMBERS UP ON EACH OTHER WRITE DOWN NUMBERS 8 6 2 4 10 YOU HAVE 10 CRANKSHAFT MAIN BEARING BOLTS. WHEN YOU LINE UP BOTH NUMBERS YOU WILL START TIGHTEN BOLTS 1 AND 2 TIGHTEN BOLTS 3 AND 4 TIGHTEN BOLTS 5 AND 6 TIGHTEN BOLTS 7 AND 8 TIGHTEN BOLTS 9 AND 10 YOU ARE TIGHTEN BOLTS IN A CRISS CROSS PATTERN. BESURE TO POUR OIL OR LUBRICATE CRANKSHAFT AND BEARINGS WITH CLEAN ENGINE OIL.WHEN YOU TORQUE MAIN BEARINGS TORQUE ALL THEM TO 20 FT LBS AND SECOND PASS TORQUE ALL BOLTS TO FINAL TORQUE 48 FT LBS. IF YOU RUN TO ANY PROBLEMS. YOU CAN BUY A HAYNES REPAIR MANUAL IT CAN HELP YOU.

Mar 02, 2011 | 1989 Honda Civic

1 Answer

2004 mazda 6 3.0L V6 main bearing caps(bootom end) has 16 bolts need torgue specs please!


Okay, the main bearing caps only have 10 bolts, i think your looking for the connecting rod caps, they have 16 bolts, i will list them both, theres a tightening sequnce for the main bearing caps, these are the caps that hold the crankshaft to the engine block, the connecting rod caps hold the pistons to the crank and they have 16 nuts,For a 2004 mazda 6 with the 3.0 engine the torque specs are as follows.
Connecting rod bolts step 1) 19.2 - 23.6 ft lbs.
step 2) tighten an additional 80 - 100 degrees

Main bearing caps step 1) 32.5 - 33.9 ft. lbs.
step 2) tighten an additional 175 -185 degrees.
heres a diagram for main caps to tighten in order.
hope this is helpful.fc3bff9.gif

Aug 20, 2010 | 2003 Mazda Mazda6

1 Answer

What are the torque specs for the main & rod bearing caps on a 2000 chevy s-10 2.2?


The head bolts are toque to yield on these engines, meaning that once they have been torqued to specification, they must be replaced when removed. If it is an OHV engine (solid push rods with and internal camshaft and rockers on the head studs) there is a sequence to tightening the head bolts. First, tighten all bolts in a circular motion, starting from the center and working outwards. I prefer to go in a clockwise rotation, but as long as it is in the correct order, rotation is not important. The long bolts must first be tightened to 22 lb/ft and the short ones to 23 lb/ft. Next, in the same order as before, tighten the long bolts to 43 lb/ft and the short bolts to 46 lb/ft. Finally, in the same order as the previous two steps, torque all the bolts an ADDITIONAL 100 degrees (10 degrees past 1/4 turn). A torque angle meter is required to do this properly and to specification. A routine of mine that is not necessary, but I have found helps prevent warping when torquing the head, is when torquing to final spec of 100 degrees, first tighten 60 degrees on all the bolts in the same order as the first two steps, then an additional 40 degrees all around in the same order.


Tightening order:
8 4 1 5 9
7 3 2 6 10

Mar 20, 2010 | 2000 Chevrolet S-10

1 Answer

Need torque for a 2000 Toyota Celicia GT 1.8L


Crank Main caps Tightening Torque

For the 12 Pointed Head Bearing Cap Sub-Assembly Bolts
Start from center bolts and tighten in a clockwise rotation working out
Step 1 all bolts 22 Nm or 16 ft lb
Step 2 all bolts 44 Nm or 32 ft lb
Step 3 all bolts 45 degrees additional clockwise rotation using an angle indicator.
Step 4 all bolts 45 degrees additional clockwise rotation using an angle indicator.

Hexagon Head Bearing Cap Sub-Assembly Bolts
1ZZ-FE Engine 18.5 Nm (14 ft.lb)
2ZZ-GE Engine 18 Nm (13 ft.lb)

Connecting rod:
1. Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.
2. Install and alternately tighten the 2 connecting rod cap bolts in several passes. Torque: 1ZZ-FE: 20 Nm (204 kgf-cm, 15 ft. lbs.) 2ZZ-GE: 30 Nm (306 kgf-cm, 22 ft. lbs.) If any of the connecting rod cap bolts does not meet the torque specification, replace the connecting rod cap bolts.
3. Retighten the cap bolts by 90° more
4. Check that the crankshaft turns smoothly.

moz-screenshot.pngmoz-screenshot-1.png

Mar 18, 2010 | 2000 Toyota Celica

1 Answer

Does anyone know the crank main bearing nut torque Alfa V6 3l


Torque to 25Nm, then tighten through a further 79 degrees. You need an angle gauge to do it properly.

Jan 29, 2010 | 1986 Alfa Romeo GTV6

2 Answers

Rod bearing torque setting for a 1992 chevy lumina 3.1


tighten to close bearing cap snug only, bearing snapped in, tork 10 PSI one bolt then the next tighetn to 20 PSI then test to see if bearing is not binding next tighten to 28 PSI check for free movement of crank then your done. Use lock tight on the nuts.

Aug 27, 2009 | 1992 Chevrolet Lumina

1 Answer

Internationl 345 v8 torque settings


Head bolt torque: 90-100 ft lbs., to be reached in 3 equal tightening steps, below is the sequence:
9 3 1 6 8
Front of vehicle
7 5 2 4 10

Main bearing cap torque: 75-85 ft lbs.
Rod bearing cap torque: 45-55 ft lbs.
Looks like u've been busy, and will be for a while. Good Luck!

Nov 15, 2008 | 1984 Dodge D150

Not finding what you are looking for?
2007 Hyundai Atos Prime Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...