Question about 2001 Ford Windstar

Open Question

How do I remove Rear Fan - 2001 Ford Windstar

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the rear a/c fan motor in my 08 Acura M D X?


  1. Remove the center console. ....
  2. Disconnect the 2P connector (A) from the rear blower motor (B), then remove the wire harness clips (C). Remove the self-tapping screws and the rear blower motor from the rear HVAC unit.
  3. Install the motor in the reverse order of removal.

Nov 14, 2014 | 2008 Acura Mdx

1 Answer

Right rear fan motor makes knocking sound


remove the fan and look for leaves or a nest

Sep 05, 2012 | 2003 GMC Envoy

1 Answer

How do i get to the ac fan motor 2000 jimmy


  1. Disconnect the VCM or the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the cooling tube from the blower motor.

  1. Disconnect the electrical connector
  2. Remove the 5 blower motor and tan assembly mounting bolts
  3. Remove the blower motor and fan assembly
    Reverse procedure to install. Don't forget that cooling tube. It looks useless but is very important to reinstall.

Aug 15, 2012 | 2000 GMC Jimmy

1 Answer

How do you remove blower motor on 1998 chevy S10 pickup


Remove the coolant reservoir.
Remove the rear coolant recovery reservoir mounting stud.
Disconnect the cooling tube from the blower motor.
Disconnect the electrical connector.
Remove the 5 blower motor and fan assembly mounting bolts.
Remove the blower motor and fan assembly.
Reverse proceedure to install.

Jul 30, 2011 | Chevrolet S 10 Cars & Trucks

1 Answer

How do I remove the alternator from a 93 ford bronco?



IDENTIFICATION

There are 4 different types of alternators found on the years and model ranges covered in this information:

  1. Rear Terminal, External Regulator, External Fan Alternator
  2. Side Terminal, Internal Regulator, External Fan Alternator
  3. Leece-Neville 165 Ampere Alternator
  4. Integral Rear Mount Regulator, Internal Fan Alternator

Rear Terminal, External Regulator, External Fan Alternator
This unit utilizes a separate, external electronic regulator. The regulator is non-adjustable. The rear terminal alternator was standard equipment on 1987 trucks, and can be found on some 1992 motor home chassis models equipped with the 7.3L diesel or 7.5L gasoline engine.
Side Terminal, Internal Regulator, External Fan Alternator
This unit was optional on 1987, standard on all 1988-92 models and standard on 1993-96 models equipped with the 4.9L and 7.5L engines. The regulator in integrated within the alternator body and is not adjustable.
Integral Rear Mount Regulator, Internal Fan Alternator
This alternator is standard equipment on all 1993-96 models equipped with 5.0L, 5.8L gasoline engines and 7.3L diesel engines (except the 1996 F-Super Duty models).
Leece-Neville 165 Ampere Alternator
This unit is optional equipment on some 1989-94 trucks and ambulance packages. A separate, electronic, fully adjustable regulator is employed in this system.
Mitsubishi 215 Ampere Alternator
This unit is found on 1996 F-Super Duty models equipped with the 7.3L diesel engine. The regulator is integral and the fan is external.


REMOVAL & INSTALLATION



See Figures 1, 2, 3 and 4



0996b43f8022502d.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Disengage all wiring harness connections from the alternator



0996b43f8022502e.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Once it is unbolted, maneuver the alternator from the engine compartment



0996b43f8020d83e.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Side terminal alternator



0996b43f8020d83f.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: Rear terminal alternator

  1. Disconnect the battery ground cable.
  2. Remove the adjusting arm bolt.
  3. Remove the alternator through-bolt. Remove the drive belt from the alternator pulley and lower the alternator.

Some engines are equipped with a ribbed, K-section belt and automatic tensioner. A suitable tool must be made to remove the tension from the tensioner arm. Loosen the idler pulley pivot and adjuster bolts before using the tool..
  1. Label all of the leads to the alternator so that you can install them correctly and disconnect the leads from the alternator.
  2. Remove the alternator from the vehicle.
  3. To install, reverse the above procedure. Observe the following torques:

    Pivot bolt: 58 ft. lbs. (78 Nm) Adjusting bolt: 25 ft. lbs. (34 Nm) Wire terminal nuts: 60-90 inch lbs. (6.8-10.1 Nm)

Dec 15, 2010 | 1993 Ford Bronco

1 Answer

Where are the bolts to remove the starter on a 1993 quad 4 grand am?


REMOVAL & INSTALLATION
Except 2.3L and 2.4L Engines

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle. Disconnect the electrical wiring from
    the starter, if accessible.
  3. If necessary for access, unfasten the three dust cover bolts, then pull the
    dust cover back to get to the front starter bolt. Remove the front starter bolt.

  4. Remove the rear support bracket.
  5. Pull the rear dust cover back (if applicable) to gain access to the rear
    starter bolt and remove the rear bolt.
  6. Note the number and location of any shims.
  7. Push the dust cover back into place (if removed), then lower the starter
    (disconnect any wiring if previously inaccessible) from the vehicle.
    To install:

  8. Position the starter in the vehicle, connect the wiring, then install the
    rear starter bolt.
  9. Install the front starter bolt, then tighten both bolts to 32 ft. lbs. (43
    Nm)
  10. If removed, install the dust cover and the rear support bracket.
  11. Connect the electrical wiring to the starter, if not already attached.
  12. Carefully lower the vehicle, then connect the negative battery cable.




    Fig. 1: Once the vehicle is raised and safely supported, you
    will be able to see the starter motor
    86883015.jpg





    Fig. 2: After disconnecting the wiring, remove the starter
    mounting bolts
    86883016.jpg





    Fig. 3: When removing the starter, be sure to note the number
    and location of any shims
    86883017.jpg





    Fig. 4: View of the starter mounting - 3.1L and 3.3L engines
    91062g09.gif

2.3L Engine
1988-89 (VIN D)

  1. Disconnect the negative battery cable.
  2. Remove the air cleaner to throttle body duct.
  3. Label and detach the TPS, IAC and MAP sensor connectors.
  4. Remove vacuum harness assembly and the MAP sensor vacuum hose from intake
    manifold, then position aside.
  5. Unfasten the cooling fan shroud attaching bolts, then remove the shroud
    (including the MAP sensor).
  6. Remove the coolant fan-to-upper radiator support bolt, then unfasten the
    remaining upper radiator support bolt and the upper radiator support.
  7. Detach the connector from the cooling fan.
    NOTE: Because of the low clearance, be very careful not to
    damage the TPS lock tang with the fan bracket.


  8. Lift the fan assembly out of the two lower insulators. Rotate the bracket so
    the two lower bracket legs point upward. Move the fan assembly toward the left
    (drivers) side until the fan blade overlaps the radiator tank-to-core seam about
    1 inch (25mm). Lift the fan assembly from the engine compartment.
  9. Remove the harness retaining clip from the engine mount bracket stud.
    Unfasten the starter mounting bolts.
  10. Tilt the rear of starter towards the radiator, pull the starter out, then
    rotate solenoid towards the radiator to gain access to the electrical
    connections.
    NOTE: Be careful not to damage the crank sensor mounted
    directly to the rear of the starter. If it gets damaged, it must be replaced.


  11. Detach the electrical connectors from the solenoid.
  12. Move the starter toward the driver's side of the vehicle, then lift it from
    the vehicle.
    To install:

  13. Insert the starter between the throttle body and the air cleaner housing,
    then move it toward the right (passenger) side.
  14. Attach the solenoid electrical connectors. Make sure to properly position
    the plastic guard over the stud and nut for the battery cable.
  15. Rotate the starter into the proper position, install any shims that were
    removed and secure using the mounting bolt. Tighten the bolts to 74 ft. lbs.
    (100 Nm).
  16. With the fan's bracket two lower legs facing upward, place the fan assembly
    between the throttle body and the radiator while overlapping the radiator
    tank-to-core seam with the fan blade by about 1 inch (25mm). Be careful not to
    damage the lock tang on the TPS.
  17. Rotate the fan bracket, then place the two lower legs into the insulators.
  18. Attach the electrical connector to the cooling fan.
  19. Install the upper radiator support and the coolant fan should, then install
    the fan-to-upper radiator support mounting bolt.
  20. Connect the MAP vacuum hose and the vacuum harness assembly to the intake
    manifold.
  21. Attach the TPS, IAC and MAP sensor connectors.
  22. Install the air cleaner to throttle body duct.
  23. Connect the negative battery cable, then check for proper starter operation.

1990-95 (VIN D), 1989-94 (VIN A), 1992-94 (VIN 3)

  1. Disconnect the negative battery cable.
  2. If necessary for access, remove the air induction tube.
  3. Detach the coolant fan electrical connector, then remove the fan assembly.
  4. Remove the oil filter, if necessary for access to the starter.
  5. For vehicles through 1990, remove the intake manifold brace.
  6. Remove the mounting bolts; some engines may have 3 starter mounting bolts.
    Pull the starter out of the hole and move toward the front or passenger side of
    the vehicle.
  7. Disconnect the wiring from the solenoid.




    Fig. 5: Starter mounting for 2.3L engine - 1990-95 models
    91062g10.gif

  8. Remove the starter by lifting it between the intake manifold and the
    radiator.
    To install:

  9. Lower the starter between the intake manifold and the radiator, then connect
    the wiring to the solenoid.
  10. Rotate the starter into installation position and install the mounting
    bolts. For vehicles through 1994, tighten to 74 ft. lbs. (100 Nm). For 1995
    vehicles, tighten the bolts to 32 ft. lbs. (43 Nm).
  11. If equipped, install the intake manifold brace and oil filter, if removed.
  12. Install the cooling fan assembly, then attach the electrical connector.
  13. If removed, install the air induction tube.
  14. Connect the negative battery cable and check the starter for proper
    operation.

2.4L Engine

  1. Disconnect the negative battery cable.
  2. Remove the air inlet duct attached to the throttle body.
  3. Remove the top starter bolt.
  4. Raise and safely support the front of the vehicle securely on jackstands.
  5. Remove the lower starter bolt.
  6. Position the engine wiring harness aside.
  7. Position the starter for access to solenoid wiring.
  8. Remove the wiring attached to the starter.
  9. Carefully lower the starter.
    To install:

  10. Attach the wiring to the starter and position the assembly into place.
  11. Install the lower starter bolt.
  12. Reposition the wiring.
  13. Lower the vehicle and install the upper starter bolt. Tighten the bolts to
    66 ft. lbs. (90 Nm).
  14. Attach the air inlet duct to the throttle body.
  15. Connect the negative battery cable.


prev.gif next.gif

Oct 31, 2010 | 1993 Pontiac Grand Am

2 Answers

2002 jeep grand cherokee larado is over heating. The cooling fanonly runs if I hotwire it. I changed th thermostat. Temp gauge is reading . Could it be the cooling fan relay if so where is it located. The...


Fan relay is located under pass headlight. Remove light assembly, use 2 1/2 " hole saw to drill hole in plastic housing ,3"from back wall, 3'' from left side.This will put you right over relay. Unscrew two bolts,replace. Relay was $40.... dealer wanted$350 to remove front bumper to replace it.

Sep 02, 2010 | 2002 Jeep Grand Cherokee

1 Answer

Safari 92 how can I get TO that heater fan?


you have to remove cowl vent grille.disconnect the transmission link from the crank arm on the motor by prying it toward the rear of the vechicle.remove the motor mounting bolts and remove the motor.then put new fan motor back in visa versa.

Nov 26, 2009 | GMC Safari Cars & Trucks

1 Answer

Fan motor for cooling rear of 2003 pilot not operating


Center console need not be removed. Right side kick panel needs to be popped out, exposing the fan motor assebly. There are 3 screws securing the assembly to the duct. Remove the screws using a flathead screwdriver, unplug the unit and pull it out. The challenge will be finding a replacement motor, as they are not sold anywhere other than the dealerships (at an outrageous price)

Aug 13, 2009 | 2003 Honda Pilot

Not finding what you are looking for?
2001 Ford Windstar Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...