Question about 1994 Nissan Quest

Open Question

Torque on intake manifold bolts 1994 nissan quest

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

ewashmidas
  • 362 Answers

SOURCE: changing water pump on 1994 nissan quest

There is no easy way, water pumps are hard to change on this vehicle. Before starting the job I would buy a repair manual with step by step instructions. To give you some idea on how long it may take, the labor time is 4.5 hours for an experienced tech.

Posted on Jan 28, 2009

SOURCE: head bolt torque settings for 720 nissan cab 2

dear friend-your torque setting on the 720 is the same as the L18 and is set at 85 - 90 nm.

Posted on Jul 23, 2009

pippall
  • 1486 Answers

SOURCE: 1994 nissan quest crankshaft rear main seal removal

There is no other way other than to remove the engine.I now its a lot of work but if you want to do the job properly then thats the way to do it.You can remove the gearbox and try.I think thats a waist of time good luck.

Posted on Jul 28, 2009

emissionwiz
  • 74896 Answers

SOURCE: how to remove front rotors on 2005 nissan quest

you need to remove the caliper mounting bracket assembly and then the rotors just slide off, go to link for pictures.
http://www.2carpros.com/how_to/how_to_replace_brakes.htm

Posted on Oct 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

(1) What is the specific Newtom torque or lb-ft for the sparks plugs NGK LZKAR6AP-11 for Nissan Tiida St C-11 2011. Engine: MR18075675R, Vin:MNBBAC11A0016494.


You miss understand why things need to be torqued .
Torque is not specific to the vehicle its the bolt how hard what is thread pitch how many threads per in or mm how many bolts and what kind compression is required .
Compression always needs to be even say you have a cork gasket on an oil pan with 25 bolts 10 ft lbs on each would give you 250 ft lbs of force but if not done in stages evenly you would be snapping bolts and bending the pan and would leak oil from the start .
Spark plugs have seals 5/8 25 lb ft is fine but its not something you are going to get a torque wrench on .

Jun 15, 2016 | Nissan Tiida Cars & Trucks

1 Answer

Torque specifications for manifold gasket bolts on a 94 olds 88


Intake manifold-to-cylinder head bolts....96 in-lbs
Intake manifold, upper to lower bolts ....132 in-lbs

Tighten all bolts from center of manifold towards the ends.

Sep 16, 2015 | 1994 Oldsmobile 88

1 Answer

1994 mpv 3.0 torque specs intake


Torque Specs :

Intake manifold bolts...72-105 in/lbs or 6-9 ft/lbs
EGR valve bolts........165-225 in/lbs or 14-19 ft/lbs
Remaining little bolts for brackets, etc......72-95 in/lbs or 6-8 ft/lbs

Aug 04, 2012 | 1994 Mazda MPV

1 Answer

WHAT IS THE TORQUE ON A 94 BUICK CENTURY 3.1 V6 ON THE INTAKE AND EXHAUST PUSH RODS?


Tightening sequence would be to tighten from the center most bolts to the outer most bolts.
Intake Upper Bolts = 18 lb.ft.
Intake Lower Bolts = 10 lb.ft.
Exhaust Manifold Nut = 12 lb.ft
Exhaust Manifold pipe = 22 lb.ft.
Exhaust Manifold Heat Shield = 18 lb.in.
Rocker Arm Torque Nuts = 18 lb.ft.

Hope this helped you ?? if you need more info, get back to me.....

Jun 16, 2011 | 1994 Buick Century

1 Answer

I need torque specks for valve train for a 1987 nissan truk v6 3.0 litter


cylinder head bolts 40 - 47 ft lbs, intake manifold bolts 12 - 14 ft lbs. , intake manifold nuts 17 - 20 ft lbs. , rocker arm shaft bolts 13 - 16 ft lbs. exhust manifold bolts 13 - 16 ft lbs. i hope this helps.

Dec 22, 2010 | Nissan Pickup Cars & Trucks

2 Answers

What are the torque measurements for the rocker arms and intake manafold?


2.2L Engine & 2.4L Engines
These engines are not equipped with rocker arms. The camshafts directly actuate the valves.

3.1L Engine & 3.4L Engines
When install or connect the check the following:
- Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm). - Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).
- Heater bypass pipe. Torque the screw at the water pump to 106 inch lbs. (12 Nm), the bolt at the cylinder head corner to 18 ft. lbs. (25 Nm) and the nut to 18 ft. lbs. (25 Nm).


About the INTAKE MANIFOLD...
-
Intake manifold nuts and bolts and tighten to 89 inch lbs. (10 Nm)
- Pushrods and rocker arms. Torque the bolts to 89 inch lbs. (10 Nm) plus an additional 30 degree turn. - Lower intake manifold. Apply sealant to the threads of the bolts and torque the bolts to 115 inch lbs. (13 Nm).



859cdc3.jpg

Exploded view of the upper and lower intake-3.1L & 3.4L engines


fe92b8b.jpg

Fig. Lower intake manifold tightening sequence-3.1L & 3.4L engines

Hope help.

May 04, 2010 | 2000 Pontiac Grand Am GT

1 Answer

Torque on 1994 Mazda pick up


if its a four cylinder(lets hope)the specs are 80-90ft.lbs torque.if its a six cylinder it is 14ft.lbs torqueat 90 degree intervals then repeat until correct torque has been reached.bad news is you can not use the same bolts on the six cylinder engine.have to be new to keep from breaking them

Jul 24, 2008 | 1994 Mazda 2WD B Series Pickup

Not finding what you are looking for?
1994 Nissan Quest Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...