Question about Cars & Trucks

1 Answer

Inside front caliper making contact with disc brake

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 42,133 Answers

The disc pad has completely worn away and the metal backing is doing the contacting

Posted on Apr 13, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

yotaguy
  • 232 Answers

SOURCE: 1994 Toyota pickup front brakes don't release

Well I don't think you'll need to buy parts,it sounds like there may be sludge built up between the master cylinder and the proportional valve to the front brakes.Pull the valve off(follow the line off the master cylinder and you'll find the valve)clean it and then flush/bleed the master cylinder before you reinstall,Then flush/bleed the rest of the system.There's a relly good chance that may be all you need to do,but you may need to pull the calipers and clean them also.Comment back if you need more help,Good Luck(To)Yotaguy

Posted on Apr 25, 2009

  • 9 Answers

SOURCE: Removing front calipers to 2003 vw passat w8

go to a tool store and ask for an easy-out, this is a specialty tool placed on a drill to grip stripped screws and broken bolts

Posted on Apr 27, 2009

  • 226 Answers

SOURCE: right front brake caliper freezes up on occassion

You either need to rebuild it correctly, or replace it - which is the most common thing to do. Since you probably have crud in it, you may have the other side crud up as well, so the best thing to do would be to change both. -or redo both brakes on the front end. Hope this helps, Rick

Posted on May 04, 2009

roniecon
  • 6826 Answers

SOURCE: 2006 Kia Spectra 5 rear brake disc replacement

One side,turns right,and push in slightly,and the other side turns left,to retract.

Posted on Apr 20, 2010

  • 972 Answers

SOURCE: 2006 Kia Spectra 5 rear brake disc replacement

you need a special tool avalable at most parts stores. its a disc brake piston turning tool. you have to rotate piston clockwise while pushing in on piston. you can fabricate something that enguages the slots and push and turn till all the way in.make sure to note position of slots and put them in same place as was before or the pin on the pads wont enguage the slot

Posted on May 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i remove the brake caliper on a 1994 f350 4x4 there are no bolts attaching it


If this is a Pin Slider, here is 1996 steps:

Section 06-03: Brakes, Front Disc 1996 F-150, F-250, F-350 4x2, 4x4, Bronco and F-Super Duty Vehicles Workshop Manual
REMOVAL AND INSTALLATION Caliper
Heavy-Duty Rail Slider, F-Super Duty
Replace brake shoe and lining (2001) as follows when the lining is worn to a minimum thickness of 0.794mm (1/32 inch) above the front disc brake rotor shield. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Always replace all brake shoes and linings on an axle. Never replace only one wheel (1007).
Removal
  1. To avoid fluid overflow when the caliper pistons are pressed into the caliper cylinder bores, siphon or dip part of the brake fluid out of the brake master cylinder reservoir (2K478). Discard the removed fluid.
  1. Raise the vehicle and install safety stands. Remove the front wheel and tire assembly.
  1. Place an appropriate size C-clamp on the disc brake caliper with end of clamp against caliper and end of screw against outer shoe. Tighten the clamp to bottom the caliper pistons in the cylinder bores. Remove the clamp. Do not use a screwdriver or similar tool to pry caliper pistons (2196) away from the front disc brake rotor (1125).




  1. Clean excess dirt from area around pin tabs.
  1. Tap upper caliper pin toward inboard side until pin tabs touch the front wheel spindle.
  1. Using Hydraulic Caliper Pin Remover D89T-2196-A or equivalent and a light hammer, drive the pin from the disc brake caliper as follows:
    1. Position the notched end of the tool against the caliper pin (retention tab half), at a 45-degree angle from the pin retention tabs.



    1. Tap the tool with the hammer to compress the retention tabs.



    1. As the retention tabs are compressed, move the tool to gain a straight approach to the caliper pin, and continue tapping to drive the caliper pin through the caliper/spindle groove.
  1. Repeat removal procedure for lower caliper pin.
  1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not let the disc brake caliper hang by the front brake hose (2078). The front brake hose could become stretched or twisted which can cause the front brake hose to leak and rupture, resulting in failure.
    Remove the disc brake caliper from the front disc brake rotor. If the disc brake caliper is to be removed for service, remove the front brake hose from the disc brake caliper. Plug the end of the front brake hose to prevent fluid loss and entry of air into the system. If the disc brake caliper is not to be removed, wire it up to the frame of the vehicle to avoid damage to the front brake hose.
Installation
stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Always replace all brake shoes and linings on an axle. Never replace only one wheel.
  1. NOTE: There is a raised section at one end of each shoe so installation can be made in one direction only.

    Install new inner and outer lining.
  1. Lubricate the knuckle upper and lower inner pad grooves and caliper grooves with Disc Brake Caliper Slide Grease, Silicone Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A. Install the disc brake caliper on a front wheel spindle, making sure the mounting surfaces are free of dirt.
  1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow the tabs of the caliper pin to be tapped too far into the spindle groove. If this happens it will be necessary to tap the other end of the caliper pin until the tabs snap into place. The tabs on each end of the caliper pin must be free to catch on the spindle flanks.
    Position caliper pin with the pin retention tabs oriented adjacent to the spindle groove.
  1. Tap the caliper pin on the outboard end with a hammer. Continue tapping the caliper pin inward until the retention tabs on the sides of the caliper pin contact the spindle face. Repeat procedure for the lower caliper pin.


Oct 23, 2011 | 1994 Ford F350 Crew Cab

1 Answer

Front disc brake assembly diagram


SECTION 206-03: Front Disc Brake 1999 Escort/Tracer Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 06/06/1998 Front Disc Brake Front Disc Brake System Components
Item Part Number Description 1 1125 Front Disc Brake Rotor 2 2B296 Disc Brake Caliper Locating Pin 3 2B120 Disc Brake Caliper 4 2001 Brake Pads 5 - Copper Washers (2 Req'd) 6 - Banjo Bolt 7 2078 Front Brake Hose 8 2W303 Brake Caliper Bolt- (2 Req'd) 9 2814 Brake Hose Clip The front disc brake system consists of a single-piston front disc brake caliper (2B120) and a ventilated front disc brake rotor (1125). The brake shoes and linings (2001) are held in the front disc brake caliper by two front disc brake caliper locating pins (2B296) and two springs. The inboard brake shoe and lining is equipped with a wear indicator that makes a squealing noise when the brake shoes and linings are worn beyond recommended use.

2010&c18=modelyear&c20=n41287&c35=wsm%2cfront%20disc%20brake%2csxf%2c206-03%2cdescription%20and%20operation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=428&ct=lan&hp=n&[aqe] ddll111_28.gif

Dec 15, 2010 | 1999 Mercury Tracer

1 Answer

How do you get the capierer pin off to put front brake pads on my Mercury Sable LS?


Section 06-03: Brakes, Front Disc 1999 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478) . Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120) , front disc brake rotor shield (2K004) or front wheel knuckle (3K185) .
  1. Remove rear brake pin retainers (2N386).
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125) . Do not pry directly against metal caliper piston or damage will occur.
  1. NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .

    Position disc brake caliper out of the way.
  1. Remove inner outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate .
  1. Inspect both rotor braking surfaces. Minor scoring or buildup of lining material does not require machining or replacement of front disc brake rotor.
-----------------------------------------------------------------
remove the 2 pins, #10 in pic. Usually has a dust cover over pin accessopening. Usually torx haed or hex head bolts (pins).


snorkelbobby_7.gif

Nov 12, 2010 | 1999 Mercury Sable

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

1 Answer

Replace rear brake pads


Rear disc brake pads offer better performance and are not as affected by moisture like conventional brake shoe style brakes are. Rear disc brakes are similar to front disc brakes. The main difference is that rear disc brake systems must incorporate the emergency brake system. There are two methods widely used for the emergency brake with rear disc systems. The first system is a brake shoe inside the brake disc that is actuated by the emergency brake lever. The second is a screw style actuator inside the brake caliper. When activated the brake pads are forced into the brake disc and held tightly by the emergency brake lever.
READ COMPLETELY BEFORE STARTING
Step 1 - Identify Rear Disc Brake Components
rear_brake_pads.jpg Rear disc brake assembly includes; rear brake disc, rear brake pads, brake caliper mount and a caliper mounting screw. (Note: Some vehicles do not have the rotor mounting screw.)
Step 2 - Removing the Rear Brake Caliper Mount Bolts
rear_brake_pads_2.jpg To replace rear brake pads and rotors the rear brake caliper needs to be removed. First loosen the rear brake caliper mount bolts and remove them. Turn counter clockwise.
Step 3 - Lift Rear Brake Caliper from The Caliper Mount
rear_brake_pads_3.jpg After the caliper mount bolts have been removed, gently lift the brake caliper from the caliper mount. Inspect the caliper slides; they should move freely in the caliper mount. Remove rear brake pads and hardware.

Step 4 - Removing Caliper Mount Bolts
rear_brake_pads_4.jpg With a socket wrench or other appropriate removal tool, loosen the rear brake caliper mounting bolts. Remove bolts and lift the caliper mount and remove it from the vehicle. Remove the retaining screw from the disc mounting hole. Tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub holding on tightly, using both hands. You do not want to drop the rotor.

Step 5 - Removing Rear Brake Rotor
rear_brake_rotor.jpg Remove the retaining screw from the disc mounting hole, tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub, hold on using both hands and do not drop.

Step 6 - Install New Brake Rotor
rear_brake_rotor_2.jpg Check the new rotor against the old brake rotor to make sure they are the same size. Clean the mating surface on the wheel hub before the new brake rotor is installed. Reinstall rotor retainer screw.
Step 7 - Reset Rear Brake Caliper
rear_brakes_7.jpg Before new brake pads can be installed, the rear brake caliper must be reset. The reset tool winds the piston back into position so the new brake pads will fit. This style of brake caliper will not compress with a clamp tool; it can only be reset with the proper reset tool.
Step 8 - Reinstall Rear Caliper Mount and Install New Rear Brake Pads
rear_brake_rotor_3.jpg After the caliper has been reset, reinstall caliper mounting bolts and make sure the bolts are tight. Then match up the old brake pads to the new brake pads. They should be exactly the same except, of course; the old ones will be worn out. Check the new brake pads for proper fit and install any brake hardware that is required.
Step 9 - Remount Rear Brake Caliper
rear_brake_rotor_4.jpg Reinstall the brake caliper, align brake pad hardware and reinstall caliper mounting bolts. (Note: align the rear peg of the brake pad to the groove in the caliper piston.) Recheck and retighten all caliper and caliper mount bolts. Bleed brake system to relieve any air in the system. Before driving the vehicle, push the brake pedal down and let it up slowly. This operation forces the brake pads to travel to the brake rotors. DO NOT DRIVE VEHICLE until proper brake pedal operation resumes. When test driving vehicle listen for any unusual noises during the operation of the brakes.
WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary clothing before inspection or work begins. Never crank an engine over when anyone is near the battery or engine. Always have an operational fire extinguisher close by, obey all first aid instructions in the event of an injury. Never stand in front or behind a vehicle when cranked over or running. When engine is cranked over keep hands and clothing away from rotating components. Never move a car without proper brake pedal operation.

Jun 01, 2010 | 1995 Saab 900

1 Answer

How to change the brakes on a 1998 ford windstar?


Very easy! I owned several different year Windstars....very good van...

Changing the pads are very easy. Here is the instructions:

Removal & Installation
  1. Remove the brake master cylinder reservoir cap. Siphon and recycle approximately half the fluid from the reservoir.
  2. Raise and support the vehicle safely.
  3. Remove the wheels.
  4. Remove the disc brake caliper guide pins.
It is not necessary to disconnect the hydraulic lines.
  1. Lift the disc brake caliper from the anchor plate.
  2. Position the disc brake caliper out of the way by suspending with a wire.
  3. Remove the brake pads from the anchor plate.
To install:
  1. Inspect the rotor surfaces for scoring or buildup of lining material. Minor imperfections do not require machining. Hand sand the glaze from the rotor using 150 grit aluminum oxide sand paper.
  2. Use a C-clamp and wooden block to seat the disc brake caliper hydraulic piston in its bore, as illustrated. This must be done to provide clearance for the disc brake caliper to fit over the front rotor during installation.
  3. Remove all built-up rust from the inside of the brake caliper pad contact area.
  4. Install the brake pads, with the clip on insulators, into the front brake caliper anchor plate.
  5. Install the disc brake caliper onto the anchor plate.
  6. Install the disc brake caliper guide pins and tighten to 23-38 ft. lbs. (31-38 Nm).
Failure to tighten the lug nuts to the proper torque in a star pattern may result in damage to the brake rotor.
  1. Install the wheel and tighten lug nuts to 83-112 ft. lbs. (113-153 Nm).
  2. Lower the vehicle.
  3. Pump the brake pedal to seat the brake pads.

May 28, 2010 | 1998 Ford Windstar

1 Answer

How do you replace the front brake caliber on a 1997 ford expedition


Caliper Removal
  1. svj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use heat to loosen a seized lug nut . Heat can damage the wheel and the wheel bearings.
    Loosen the lug nuts.
    1. Remove the center cap.
    1. With the weight of the vehicle on the wheels, loosen the lug nuts.
      1. svj~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE ELECTRICAL POWER TO THE AIR SUSPENSION SYSTEM MUST BE SHUT OFF PRIOR TO HOISTING, JACKING OR TOWING AN AIR SUSPENSION VEHICLE. THIS CAN BE ACCOMPLISHED BY TURNING OFF THE AIR SUSPENSION SWITCH LOCATED IN THE RH KICK PANEL AREA. FAILURE TO DO SO MAY RESULT IN UNEXPECTED INFLATION OR DEFLATION OF THE AIR SPRINGS WHICH MAY RESULT IN SHIFTING OF THE VEHICLE DURING THESE OPERATIONS.
        Raise and support the vehicle.
      1. Remove the wheel and tire assembly.
        1. Remove the lug nuts.
        1. Remove the wheel and tire assembly.
      2. CAUTION: Replace the lining if worn to or past specifications. Replace the brake shoes and linings in complete axle sets. Inspect the brake shoes and linings for wear or contamination.
      3. svj~us~en~file=ani_caut.gif~gen~ref.gif WARNING: BRAKE FLUID CONTAINS POLYGLYCOL ETHERS AND POLYGLYCOLS. AVOID CONTACT WITH EYES. WASH HANDS THOROUGHLY AFTER HANDLING. IF BRAKE FLUID CONTACTS EYES, FLUSH EYES WITH RUNNING WATER FOR 15 MINUTES. GET MEDICAL ATTENTION IF IRRITATION PERSISTS. IF TAKEN INTERNALLY, DRINK WATER AND INDUCE VOMITING. GET MEDICAL ATTENTION IMMEDIATELY.
        Disconnect the front brake hose (2078).
        1. Remove the front brake hose bolt.
        1. Remove the copper washers. Plug the front brake hose.
        1. Disconnect the front brake hose
      4. Remove the disc brake caliper (2B120).
        1. Remove the two caliper bolts.
        1. Lift the front disc brake caliper (2B121) off the front disc brake caliper anchor plate.
      5. On 4x2 vehicles, measure the front disc brake hub and rotor (1102) thickness.
        • Replace the front disc brake hub and rotor if not within specifications 27.7mm Min.
      6. On 4x4 vehicles, measure the front disc brake rotor thickness.
        • Replace thhe front disc brake rotor if not within specifications. 27.7mm Min.
      7. Inspect the disc brake caliper for leaks.
        • If leaks are found, disassembly is required

Mar 10, 2010 | 1997 Ford Expedition

1 Answer

I need to know the procedure for r and r on a front rotor if this is something that can be done at home with limited tools?


1999 Taurus/Sable Section 06-03: Brakes, Front Disc 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Disc Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Be careful to avoid damage or interference with caliper bleeder screw fitting and front disc brake rotor shield (2K004).
  1. ani_caut.gif CAUTION: Handle front disc brake rotor (1125) and disc brake caliper (2B120) assembly in such a way as to prevent deformation of front disc brake rotor , and nicking, scratching or contamination of brake linings/rotor surfaces.
    NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .


    Remove caliper anchor plate bolts and discard. Position disc brake caliper out of the way. Prevent separation of caliper housing from anchor bracket because contamination of guide pin journals can occur.
  1. NOTE: If excessive force must be used during front disc brake rotor removal, the front disc brake rotor should be checked for runout prior to installation.


    If additional force is required to remove front disc brake rotor , apply Rust Penetrant and Inhibitor F2AZ-19A501-A or equivalent meeting Ford specification ESR-M99C56-A on front and rear rotor/hub mating surfaces. First, strike front disc brake rotor between lug bolts (1107) with a plastic hammer. If this does not work, attach 2-3 Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor . Remove front disc brake rotor from wheel hub (1104) assembly by pulling it off the lug bolts.
Installation
  1. If original front disc brake rotor is being installed, make sure rotor braking and mounting surfaces are clean.
  1. ani_caut.gif CAUTION: Failure to clean rust and foreign material from rotor and hub mounting faces when installing new or old front disc brake rotors will result in high rotor runout, which will speed up the development of brake roughness shudder vibration.
    Apply a small amount of Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A to pilot diameter of front disc brake rotor.
  1. Install front disc brake rotor on wheel hub assembly.
  1. Install disc brake caliper and new caliper anchor bracket bolts on front disc brake rotor . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: Failure to tighten lug nuts (1012) in a star pattern may result in high rotor runout, which will speed up the development of brake roughness, shudder and vibration.
    Install wheel and tire assembly on vehicle. Tighten lug nuts to 115-142 Nm (85-104 lb-ft) using Rotunda Accutorq® Lug Nut Socket 164-R0303 or equivalent on a 1/2 inch air impact wrench, or use a torque wrench.
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.
  1. Road test vehicle.









May 25, 2009 | 1999 Mercury Sable

2 Answers

Cant remove wheel hub


here is procedure

Section 04-01: Suspension and Wheel Hubs, Front 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Wheel Hub Bolt Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Refer to Section 04-04 .
  1. Remove disc brake caliper (2B120), and front disc brake rotor (1125). Refer to Section 06-03 .
Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478). Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120), front disc brake rotor shield (2K004) or front wheel knuckle (3K185).
  1. Remove rear brake pin retainers (2N386). ( I think it is a T 40 torx bit you need)
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125). Do not pry directly against metal caliper piston or damage will occur.
  1. Position disc brake caliper out of the way and support with wire to avoid damaging the disc brake caliper and front brake hose (2078).
  1. Remove outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate.
  1. Remove inner brake shoe and lining assembly.
  1. Position lug bolt (1107) to clear front wheel knuckle (3K185).
  1. Remove lug bolt from wheel hub (1104).



7548d8f.gif

Installation
  1. Install lug bolt into wheel hub.
  1. Using a lug nut (1012), seat wheel hub bolt into wheel hub.
  1. Install front disc brake rotor and disc brake caliper. Refer to Section 06-03 .
  1. Install wheel and tire assembly. Tighten lug nut to 115-142Nm (85-104 lb-ft).

May 25, 2009 | 1996 Mercury Sable

2 Answers

2001 brake pad replacement 2001 nissan quest


The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Apr 23, 2009 | 2001 Nissan Quest

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...