Question about Ford Cars & Trucks

1 Answer

MAP sensor for 89 Ford Ranger - Ford Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,977 Answers

What exactly are you asking for. were to get one (auto parts store or dealer) or are asking for the wire colour code, were the MAP sensor is located, or how to test it and what vacuum there should be.

Posted on Apr 12, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76164 Answers

SOURCE: 89 Ford Ranger Carrier bearing

All the bearings for the rear diff are pressed off and on, they can be done at home if u have a high quality bearing puller, but to press them on should be done at the machine shop.

Posted on Feb 09, 2009

Hightower971
  • 183 Answers

SOURCE: will '89 Ranger leaf springs fit a '99 Ford Ranger 4x4?

Measure the distance from bolt to bolt, and to the center. If they match then, they match, if not you will have to check the numbers with fords tolerances to avoid an axle wrap. But it should fit, maybe just a little stiffer of a suspension from the 4x4.
Calvin the Mobile Mechanic.

Posted on Apr 23, 2009

  • 3 Answers

SOURCE: engine coolant sensor location

behind water pump it's called freeze plug

Posted on Jun 03, 2009

  • 14036 Answers

SOURCE: specs for throttle position sensor and map sensor

OBD 1 SCANNER WOULD BE THE BEST WAY TO CHECK TPS AND MAP SENSORS.BECAUSE IF THEY ARE BAD THE SCANNER WILL GIVE YOU CODE.

Posted on Jan 01, 2010

roniecon
  • 6826 Answers

SOURCE: I have an 89 ford ranger 2.9 engine. The engine

Have the fuel pressure checked,and replace the fuel filter first,it is most likely one of the two causing the problem,if this was helpful,please rate,thank you.

Posted on Jun 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mapping codes P0107, P2263 & P2227 come up on scan tool what are these codes relating too? Ford Ranger 2008 not 2004 3.0 4 door


code p 0107 refers to manifold absolute pressure (MAP) sensor /barometric pressure (BARO) sensor --low input ====causes --wiring short to ground ---MAP sensor ---BARO sensor ---ECM
code p 2263 refers to turbo charger (TC) boost pressure /supercharger (SC) boost pressure ---performance problem====causes --mechanical fault
code p 2227 refers to BARO sensor -range / performance problem===causes wiring --- BARO sensor --- ECM
I would be testing the BARO sensor for a problem as it is listed for all 3 codes
if you don't have such a sensor you have a MAP sensor which is reading in the same area so test that as well

Oct 19, 2015 | 2004 Ford Ranger

1 Answer

Need vacuum hose diagram 89 Ranger 2.3 liter fuel injected I have 6 points on hub need egr line need map sensor line. Does it split to at map sensor.Have air recirc valve pass side.fuel press vac good


The fuel pressure regulator and the MAP sensor need to have there own lines. Everything else can be spliced together. Put the check valve to the recirculation valve.

Sep 03, 2015 | Cars & Trucks

1 Answer

Locate 1991 4.0L ford ranger map sensor


Under hood, passenger side, rear engine area, mounted on upper firewall this is it

Oct 09, 2014 | Cars & Trucks

1 Answer

How do i fix code 51 89 ranger 2.3 std trans


That code is for the coolant temp open circuit. More than likely replacing the coolant temp sensor will correc the issue but check/verify the connector and wiring for the temp sensor before you replace.

Feb 24, 2011 | 1989 Ford Ranger

1 Answer

My test light flashes code 22 1 22 on my 89 2.3 ranger. Truck idles fine but when excelerated it brakes up real bad


Hi:
You most likely are tripping a MAP sensor out of range code 22, and should check it out, especially the vacuum line going to it, and any other vacuum line under the hood,

Here is a list of codes for you

http://www.extreme-check-engine-light-codes.com/Ford%20OBD1%20Decoder.htm

Nov 06, 2009 | 1992 Ford Ranger

1 Answer

Engine coolant sensor location


behind water pump it's called freeze plug

May 08, 2009 | 1989 Ford Ranger

1 Answer

89 ranger 2.3 no spark, crank sensor replaced, module ok, ecm?


Is the sensor close enough th to the crank without contacting? About.060 gap?

Apr 27, 2009 | 1989 Ford Ranger

1 Answer

Using to much gas black exhaust 1994 ford ranger


check to see what codes are present. sounds like it is running rich check o2 sensors vacuum leaks map sensor. 

Mar 04, 2009 | 1994 Ford Ranger Supercab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...