Question about 2001 Alfa Romeo 147

1 Answer

What i need to know is the brake bleeding sequence please

Posted by Anonymous on

  • 1 more comment 
  • Naiton Apr 12, 2015

    # he mst pump abt 10 times

  • Naiton Apr 12, 2015

    # he mst pump abt 10 times

  • Naiton Apr 12, 2015

    # he mst pump abt 10 times

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 68 Answers


Tools
Small container with brake fluid and bleeding pipe,spanner,fender covers and an assitant,jack and stands
. procedure
1)Fill the brake fluid reservoir to its maximum level
2)Make sure all bleed ******* are tight and there are no nipple
3)Always start with the furthest wheel from the brake master cylinder
4)Tell your assistant to climp in the car for about 10 times.
5)as he depresses the brake pedal,with your container insert the pipe on the bleed nipple then grab your spanner and loosen the nipple,do this procedure on all wheel cylinders until there is no air bubbles seen
. conclusion
After doing all the above adjust the brake fluid level

Posted on Apr 12, 2015

Testimonial: "good sound advice"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a ford escort xr3i 1988 i have replaced the brake master cylinder, bleed the brakes but still have no brakes what could be wrong?


Your car has a diagonally split brake system. Each side of this system must be bled as an individual system, and there is a correct bleeding sequence to be followed. First bleed the right rear brake, second, bleed the left front brake, then follow with the left rear brake and lastly, bleed the right front brake.Here's a link on a repair guide for bleeding your brakes. Repair Guides Brake Operating System Bleeding The Brake System AutoZone com

May 24, 2015 | Ford Escort Cars & Trucks

1 Answer

I need a bleeding sequence for a 1994 GMC Suburban


The proper sequence to bleeding any brakes, are usually to do the one farthest away from the master cyl. first, and continue till ur at the last one. (left front). Rear brakes, then to the front brakes!

Jun 30, 2014 | 1994 Chevrolet Suburban

1 Answer

Bleeding brakes wheel sequence for 2003 Alero


Bleed the back brakes first until you get clear brake fluid then you bleed the front brakes, make sure you keep the brake master cylinder topped up so you don't get air into the brake lines..

Dec 05, 2012 | Volkswagen Golf Cars & Trucks

1 Answer

Brake bleeding sequence for 1995 buick


Most cars are done the same way:
1: Farthest brake from the master cylinder (rear)2: Opposite side from the first brake.3: Farthest from the master cylinder on the front.4: Remaining brake.
BTW: I would advice using the traditional method of using a clear bottle with some fluid in the bottom and a clear hose running out of the fluid, through the bottle top and which can connect to the bleed nipple. When bleeding fluid, make sure the fluid in both the master cylinder and to the bottle is clean before closing off the bleed nipple. Then pump the brake after bleeding each brake and feel for any softness. If you feel softness after bleeding any particular brake, then you will know that you just introduced air into that brake line, and will need to bleed again.NEVER allow your master cylinder to become totally empty whilst bleeding as this will mean you have to bleed all air out of the total system and start again from scratch. This can be a huge pain!

Nov 02, 2012 | Cars & Trucks

1 Answer

My brakes go to the floor and i need to know the bleed sequence so i can try bleeding the brakes whats the sequence


always start with the back passenger wheel, then back drivers wheel, then front passenger, last front drivers wheel, there should be a bleeder valve on each caliper, probably a 3/8 or 5/16 open end wrench, have someone pump the brakes up tight and hold it, turn the bleeder valve open until the pedal goes to the floor and retighten before they let the pedal go or it will **** air back in, continue doing this until you get a stream of fluid, no bubbles should be in the fluid, dont forget to keep adding a little bit of brake fluid every so often during bleeding

Jan 21, 2011 | 1994 Toyota Camry

5 Answers

Is there a bleeding sequence for a 1990 Toyota Four Runner? We replaced one front driver side brake line and both calipers and we cannot seem to get it to bleed properly. Thanks


normally, the brakes are bled starting from the furthest brake to the closest with respect to the master brake cylinder. the sequence is : right rear, left rear, right front, left front. pump the brakes until pressure is built up. do this rather slowly. while keeping downward pressure on the pedal, open the bleed screw slowly. the pedal will go to the floor. hold the pedal on the floor and tighten the bleed screw. do this until no air is observed. keep the reservoir. repeat with the rest of the brakes following in sequence

http://www.aa1car.com/library/2003/bf90347.htm

May 31, 2010 | 1990 Toyota 4Runner

2 Answers

Bleed brakes on 96 chevy 1/2 ton


YOUR TRUCK HAS KELSEY HAYES FOUR WHEEL DRIVE ANTI LOCK BRAKES EBC 310. YOU CAN BLEED BRAKES MANUAL STARTING AT - RR- LR RF- LF. THIS IS BLEEDING SEQUENCE.BUT YOU NEED A TECH 1 OR 2 SCANNER BECAUSE IF YOU REPLACED THE BPVM OR BRAKE PRESSURE MODULATOR VALVE.BECAUSE AIR TRAPPED IN VALVE ASSEMBLY.THE TECH 1 OR 2 SCANNER YOU HAVE PUT IN THE FUNCTIONAL TEST BLEED AIR OUT OF VALVE ASSEMBLY.THEN YOU CAN BLEED BRAKES MANUAL.

Mar 27, 2010 | 1996 Chevrolet K1500

3 Answers

Trying to bleed brake line after replacing rear rotors and pads.. not getting any pressure..


have you had problems getting pressure to the rear brakes before? if yes it is proportion valve problem if no try to sequence bleed the entire system starting with tire left rear, right rear, left front, right front. do the sequence 2-3 times.

Feb 23, 2010 | 2000 Chevrolet Blazer

2 Answers

Cant bleed out brakes


It takes time, do you know the sequence to bleed the brakes? Most cars r different. And you have to keep pouring brake fluid, That is a two person job. Make sure all lines r connected to MC and not leaking. After a while if nothing comes out MC could be diffective.

Jun 06, 2009 | 1990 Toyota 4Runner

2 Answers

I need to know how to bleed the brakes on a 1999 chevy blazer


Start from right rear, then, left rear, right front, left front. Fill master cylinder. Have helper sit in car, have helper hold brake pedal down. open bleed screw. fluid and air comes out. close screw. release brake pedal. Continue until no air comes out. Move to next wheel. Keep an eye on master cylinder fluid level after each wheel.

Mar 27, 2009 | 1999 Chevrolet Blazer

Not finding what you are looking for?
2001 Alfa Romeo 147 Logo

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Alfa Experts

old marine
old marine

Level 3 Expert

2005 Answers

David Harrelson
David Harrelson

Level 3 Expert

5324 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you an Alfa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...