Question about Cars & Trucks

1 Answer

Where is the crankshaft sensor positioned - Cars & Trucks

Posted by on

  • paulmacintyre
    paulmacintyre Apr 11, 2015

    On what type of vehicle

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,963 Answers

Try MFG website, or email their customer service, or try
manualslib.com

OR google images for your make model year you may get lucky with a picture or location diagram. But since you are a DIYer, I'd recommend you obtain a repair manual from your favorite auto parts store. You will want it next time anyway.

Posted on Apr 12, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 373 Answers

SOURCE: 97 Astro crankshaft position sensor

HI..
Tha crank position sensor On your astro is located.
On front of the engine on timing cover, left side.
Behind the crankshaft pulley. with a connector of 3 wires.

I hope this work for you.

Posted on Jul 12, 2008

polarcycle
  • 1392 Answers

SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?

it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Posted on Jun 23, 2009

  • 491 Answers

SOURCE: Replace crankshaft position sensor

Remove the left front wheel....(drivers side). Remove all accessory belts. Remove the crankshaft shaft pulley.......remove the plastic lower timing belt cover.....and there it is! It is mounted with one bolt.
The wiring runs down the right side of the timing cover while looking at it from the drivers side of the car.

Posted on Aug 17, 2009

Testimonial: "I ended up having my mechanic do the work. He did say he had to move all those parts to get to the sensor. "

GARYca
  • 672 Answers

SOURCE: Change a crankshaft position sensor on a 2000 eclipse

Is this a V6 or 4cyl???>>>(V6) This requires removing the Harmonic balancer (crankshaft pulley). Remove (R) front wheel, remove engine splash Guard, Remove crank pulley, remove lower timing belt cover. The Crank sensor is located behind the crank shaft pulley!! I highly recommend having this done by a certified tech, requires special tools. Hopefully this helps!!

Posted on Mar 11, 2010

  • 1 Answer

SOURCE: crankshaft position sensor location on 2004 chrystler pacifica

can u please tell me where on my 2004 chrysler pacifica is the crankshaft sensor located?

Posted on Apr 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft position sensor on my 2010 srx 3 liters


Camshaft/Crankshaft Position Sensor Replacement - Cadillac Forums

www.cadillacforums.com/.../261074-camshaft-crankshaft-position-senso...

May 29, 2012 - 8 posts - ‎4 authors
I have a 2004 CTS - 3.6L and am trying to get the camshaft position ... at my local Auto Zone and it simply shows camshaft position sensor A. Code P0340 Camshaft Position Sensor
14 posts
Mar 23, 2013
How to change the camshaft and crankshaft position ...
6 posts
Oct 9, 2011
Where is camshaft position sensor on 2003?
7 posts
Dec 28, 2009
Crankshaft Position Sensor 3.6L 04 CTS
5 posts
Jul 15, 2008
More results from www.cadillacforums.com

2004 Cadillac DTS crankshaft position sensors - YouTube

? 3:22
https://www.youtube.com/watch?v=jbjLJZzF3xA
Sep 16, 2013 - Uploaded by Rogelio Cervantes
Quick overview crankshaft position sensor replacement for a 2004 Cadillac DTS 4.6 liter North Star. ... 2003 Cadillac CTSCrank Position Sensor Part 3 Done!!! - Duration: 8:21. 2LateIWon 8,433 views. 8:21. How To Check .

Jan 16, 2016 | Cars & Trucks

1 Answer

Where is the crankshaft position sensor?


    Pontiac G6 Crankshaft Position Sensors - AutoZone

    www.autozone.com/1/.../pontiac-g6-crankshaft-position-sensor...
    AutoZonePontiac G6 Crankshaft Position Sensors including Crankshaft Position Sensor - Duralast (SU8213), Crankshaft Position Sensor - Duralast (SU9540), Crankshaft ... images for pontiac g6 crankshaft position sensor

Oct 28, 2015 | 2006 Pontiac G6

1 Answer

Troubleshoot crank position sensor location


For testing crank sensor,check the help link below:---How to test Crankshaft Position Sensor? http://fordrepairhelp.blogspot.in/2012/03/how-to-test-ford-focus-crankshaft.html
----------

How to test Crankshaft Position CKP Sensor?

---------------
Crankshaft Position Sensor Operation?

----------------
Replace Camshaft position sensor and Crankshaft Position Sensor? http://technoanswers.blogspot.in/2012/06/2005-dodge-durango-replace-camshaft.html
----------
GMC Crankshaft Position (CKP) Sensor Replacing? http://schematicsdiagram.blogspot.com/2011/12/gmc-crankshaft-position-ckp-sensor.html

------------
These details will help.
Thanks.

Nov 25, 2012 | 2000 Cadillac Escalade

2 Answers

99 stratus 2.5 v-6/no spark.will crank over.


CRANKSHAFT POSITION SENSOR - 2.5L

REMOVAL
  1. Remove speed control servo from driver's side strut tower.
  2. Remove crankshaft position sensor retaining bolt Crankshaft Position Sensor
  3. Pull crankshaft position sensor straight up out of the transaxle housing.
  4. (Disconnect crankshaft position sensor electrical connector from the wiring harness connector.
INSTALLATION - ADJUSTABLE All vehicles will be equipped with an adjustable crankshaft position sensor. This can be identified by an elongated mounting hole in the sensor.
NOTE: If the removed sensor is to be reinstalled, clean off the old spacer on the sensor face. A NEW SPACER must be attached to the sensor face before installation. If the sensor is being replaced, confirm that the paper spacer is attached to the face of the new sensor Crankshaft Position Sensor and Spacer
  1. Install sensor in transaxle and push sensor down until contact is made with the drive plate. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque.
  2. Connect crankshaft position sensor electrical connector to the wiring harness connector.
  3. Attach connector to heater tube bracket.
  4. Install speed control servo. Tighten nuts to 9 N·m (80 in. lbs.) torque.

May 19, 2012 | 1999 Dodge Stratus

1 Answer

HELP ! Sensor crankshaft position SUZUKI AERIO SX AWD 2.3L 2005.How to replace under the scheme ?


Welcome to FixYa.com
Crankshaft Position (CKP) Sensor Removal and Installation

Removal

1. Remove engine with transmission from vehicle.

2. Remove transmission from engine and then remove flywheel or drive plate from crankshaft.

3. Disconnect connector from crankshaft position sensor.

4. Remove crankshaft position sensor (1) from cylinder block (2).

Installation

Image

Reverse removal procedure noting the following.

- Check to make sure that crankshaft position sensor (1) is free from any metal particles and

damage.

- Apply engine oil to O-ring of sensor.

- Install crankshaft position sensor to cylinder block (2) with specified torque.

Tightening torque

Crankshaft position sensor bolt a: 6 N.m (0.6 kg-m, 4.5 lb-fl)

- Connect connector and fix wire harness with clamp securely. Thank you for Using FixYa.comKind Regards, LeeYour FixYa Expert and Master Technician
leedavidian_133.png

Feb 06, 2011 | 2005 Suzuki Aerio SX

2 Answers

I need to put a crankshaft sensor but I don't Know its location I already changed the cam sensor. Ronnie


The crank sensor is located on the engine near the flywheel axis of the crankshaft.

Crankshaft Position Sensor Removal & Installation To Remove:
Location of the crankshaft position sensor on the 2.4L engine 90904g51.gif
Location of the crankshaft position sensor on the 3.0L engine 91154g20.gif
Location of the crankshaft position sensor on the 3.3L and 3.8L engines 91154g21.gif
NOTE: On the 2.4L engine, the crankshaft position sensor is mounted to the engine block behind the alternator, just above the oil filter. On the 3.0L, 3.3L and 3.8L engines, the crankshaft position sensor is mounted on the transaxle housing, above the vehicle speed sensor.
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect the crankshaft position sensor electrical connector.
  4. Unfasten the sensor mounting screw, then remove the sensor from the vehicle by pulling it straight out.
To Install:
NOTE: If the sensor removed is going to be re-installed, clean off the old spacer on the sensor face. A new spacer must be attached to the sensor face before installation. If the sensor is being replaced, be sure that a paper spacer is attached to the sensor face.
  1. Install sensor and push the sensor in until contact is made. While holding the sensor in this position, install and tighten the mounting bolt to 105 in. lbs. (12 Nm).
  2. Connect the crankshaft position sensor electrical connector.
  3. Lower the vehicle.
  4. Connect the negative battery cable.
prev.gif next.gif

Jul 31, 2010 | 1996 Plymouth Grand Voyager

1 Answer

Where is the crankshaft sensor on a v6 2000 chrystler sebring


CRANKSHAFT POSITION SENSOR - 2.5L
REMOVAL
Remove speed control servo from driver's side strut tower.
Remove crankshaft position sensor retaining bolt Crankshaft Position Sensor
Pull crankshaft position sensor straight up out of the transaxle housing.
(Disconnect crankshaft position sensor electrical connector from the wiring harness connector.
INSTALLATION - ADJUSTABLE
All vehicles will be equipped with an adjustable crankshaft position sensor. This can be identified by an elongated mounting hole in the sensor.

NOTE: If the removed sensor is to be reinstalled, clean off the old spacer on the sensor face. A NEW SPACER must be attached to the sensor face before installation. If the sensor is being replaced, confirm that the paper spacer is attached to the face of the new sensor Crankshaft Position Sensor and Spacer

Install sensor in transaxle and push sensor down until contact is made with the drive plate. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque.
Connect crankshaft position sensor electrical connector to the wiring harness connector.
Attach connector to heater tube bracket.
Install speed control servo. Tighten nuts to 9 N·m (80 in. lbs.) torque.

May 22, 2010 | 1998 Chrysler Sebring

1 Answer

Jsut want to know where crankshaft position sensor


Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

0996b43f80202990.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

0996b43f8020299e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

Apr 15, 2010 | 2002 Ford Escape

1 Answer

I CANT LOCATE CRANK POSITION SENSOR


7X Crankshaft Position (CKP) Sensor
Lower rear of engine
4
25
--
24X Crankshaft Position (CKP) Sensor
Right hand side of engine, at end of crankshaft, behind harmonic balancer
7X Crankshaft Position (CKP) Sensor
Lower rear of engine
4
25
--
24X Crankshaft Position (CKP) Sensor
Right hand side of engine, at end of crankshaft, behind harmonic balancer
Right hand side of engine, at end of crankshaft, behind harmonic balancer

Apr 12, 2009 | 1995 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...