Question about Cars & Trucks

1 Answer

Could you send me a diagram of how to hook up the two six volt house batteries.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 511 Answers

Hi if you want to join two batteries to make 12v place the batteries side to side and. Connect the negative from one battery to the plus of the other. Then connect the batteries in the vehicle as normal plus to plus minus to minus. If the vehicle is 6v then connect plus to plus and minus to minus this will give you 6volts and double the amps. Hope this helps. Regards Jim...

Posted on Apr 11, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does the Duramax XP10000EH charge its own battery when running or do you have to hook up the alligator clips?


Should be self charge.. However If I'm not mistaken if it does not put out 13.5 volts I would check the 12 volt output socket and see if that sends out 12.5 or better volts and if it does a little re-wire job and a relay would fix this problem..

Oct 23, 2016 | Cars & Trucks

1 Answer

I have a 1993 33 foot southwind I disconnected the three batteries 2ea. six volt & 1ea. 12 volt had them charged, when I went back to re-connect I forgot where the cables went, can some one help w


Do a Google search for:
1993 Southwind battery wiring diagram
You will get a number of results, pick the one that best matches your particular situation; it will be something like this:
attachment.php?attachmentid=25156&d=1345678155
Battery Wiring and Disconnect issues in 92 Southwind iRV2 Forums

Feb 06, 2015 | Cars & Trucks

2 Answers

Radio and cd player do not work on my 95 bronco...should i replace it or try something to test it?


i would test it even if you go with an aftermarket radio you will have to have all your power and grounds.to test it simply pull the radio out to get the the wires.The red wire is a 12 volt ignition when the key is turned on it sends 12 volts to turn the radio on,the yellow wire is 12 volt constant it should always have power on it.,and finally the black wire is your ground the easy way to test the ground is to simply take a test light and hook it onto the positive post of your battery prob the wire and make sure it lights up.To check for power just do the opposite hook the lead on the light to the ground post on the battery.you may have to have a wire ( a jumper wire) to use to hook in between the battery and the test lead on your light.

Oct 07, 2013 | 1995 Ford Bronco

1 Answer

Battery drains while sitting


Hi Anonymous, perform the following tests:
1. Fill acid type batteries to proper levels.
2. Charge battery overnight at 1-2 amps you need 12.5 volts or better after charging.
3. Hook up battery positive cable, then with your multimeter on the milliamp scale connect one lead to the negative battery post and the other lead to the ground cable. Meter should read 3 milliamps or less, 10 milliamps with a radio, 15 milliamps with radio and CB. If your meter reads higher you need to isolate the circuit by pulling fuses and circuit breakers one at a time and observe meter for drop in aprerage then get out your test light and track down the short in that circuit.
3. Make sure all connections are clean and tight especially the negative cable at "BOTH" ends.
4. Hook up volt meter to battery and start engine, if meter falls below 9.5 v while cranking replace battery.
5. With engine running at 3600 RPM battery should read 14.3-14.7 volts if not continue tests.
6. Unplug voltage regulator from alternator at crankcase by front of primary cover.
7. To test voltage regulator go to: https://www.youtube.com/watch?v=F8EjV0IjW9Q
8. With ohm meter, one lead grounded, touch alternator pin meter should read infinity, if not replace stator.
9. With ohm meter, both leads touching alternator pins meter should read 0.1 to 0.2 ohms on 1989 and later models. 0.2 to 0.4 ohms 1988 and earlier models, if not replace stator.
10. With volt meter set on AC scale, both leads touching alternator pins meter should read
16 to 20 volts AC for every 1000 RPM'S 1989 and later and 19 to 26 volts AC for every 1000 RPMS. If not replace rotor.
17. For a free wiring diagram please visit the website below. Good luck and have nice day.
Harley Davidson Wiring Diagrams and Schematics

Jul 06, 2012 | Cars & Trucks

1 Answer

When I turned off my car last night it was like when a fuse blows in your house; all the electricity just cut out at once. Then no power for anything, I mean anything. I am guessing alernator, but hoping...


well first of all. check main fuse in fuse box. to check alternator--- with car off at battery, voltage should be at least 12.5 to 13 volts. then when running. there should be at least 14 volts or a bit higher, at battery. but it sounds more like a fuse then anything else. if all is satisfactory then check to see if power is going through ignition. have a good one !!

Dec 19, 2010 | 2003 Volkswagen Golf

1 Answer

I need to find an 1998 oldsmobile regency wiring diagram for free online the battery does not stay charged i have tried switching batteries and still does the same thing its only staying charged for the...


if the battery cable end have corosion on them the current is not able to charge battery. If you put a multimeter on volts dc 20volts and the car is running and charging properly, the meter should read approx. 14.73 volts. Clean the inside of the cable ends, and the posts on the battery with a wire brush, then coat all of them with some vaseline. Hook them up and tighten. If that doesn't work you will probably need the diagram, to trace a dead short.

Aug 29, 2010 | 1998 Oldsmobile Regency

1 Answer

Need to know what color 12 volt supply


My manual for a 99 300M shows two sources of 12 volt power to the mirror positioning switch, One is from the battery, switch terminal 11 wire M1, PK (pink). The other is from the start-run 12 volt line, switch terminal 5, wire G5 DB/WT (dark blue, white stripe). If you send me your email address to af6im at arrl dot net I can send you a scanned copy of the diagram.

Jun 27, 2009 | 1999 Chrysler 300M

2 Answers

I just bought a 1977 Dodge Monaco Motorhome and just replaced the house battery with a brand new marine battery. Now I'm finding that it runs all the lights and everything except the 110 outlets. I need to...


It is called an inverter, and it may not be hooked up, u will have to trace the source power for the outlets and at the source add an inverter to change 12 volts DC to 110 volts AC.

Dec 13, 2008 | Dodge Pickup Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...