Question about 2006 Dodge Ram 1500

1 Answer

My hazards and turn signals do not work in front and works Fine in back. I replaced bulbs and turn sygnal switch. I have a 2006 dodge ram 1500 slt any suggestion

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 1,326 Answers

Ground wire came loose.

Posted on Apr 15, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 188 Answers

SOURCE: 2001 dodge ram 1500 brake lights

I would guess the brake fuse ( this does not use the same fuse as the tail lights/blinkers) or the ground for the brake light bulb.

Posted on Aug 22, 2008

  • 154 Answers

SOURCE: 2000 dodge caravan turn signal switch won't work

Try the Combo Flasher. It is located in the Junction Block in the drivers area under the dash. You may have to pull off the knee panel to get at it. If you're vehicle is equipped with "Daylite Running Lamps" it will be part of that relay. Located in the same spot only a bigger relay. With the window - do the interior lites dim when it has issues going up? If so it is probably drawing to much amperage thus the motor. If not then the switch probably has poor contacts and needs replacing. Good Luck.

Posted on Apr 01, 2009

abauto
  • 353 Answers

SOURCE: o2 Dodge Dakota Brake lights wont work but bulbs r good.

If the bulbs are good I would suspect the Brake light switch.

Brake Light Switch: Testing and Inspection
The brake lamp switch can be tested with an ohmmeter. The ohmmeter is used to check continuity between the pin terminals.
Switch Circuit Identification
- Terminals 1 and 2: brake lamp circuit
- Terminals 3 and 4: RWAL/ABS module and Powertrain Control Module (PCM) circuit
- Terminals 5 and 6: speed control circuit
Switch Continuity Test
NOTE: Disconnect switch harness before testing switch continuity.
With switch plunger extended, attach test leads to pins 1 and 2. Replace switch if meter indicates no continuity.
With switch plunger retracted, attach test leads to pins 3 and 4. Replace switch if meter indicates no continuity.
With switch plunger retracted, attach test leads to pins 5 and 6. Replace switch if meter indicates no continuity.


27c4c52.jpg

Posted on Sep 11, 2009

ZJLimited
  • 17970 Answers

SOURCE: Where is the Hazard/Turn Signal switch located in

2000 Dodge Intrepid 2.7L SFI DOHC 6cyl

The Flasher is located front seating area, driver side, under left hand side of instrument panel between junction block and brake pedal.

Posted on Oct 30, 2009

Testimonial: "Yes, this was ver helpful. Thank You! PS. If that photo is the Lady that answered my question, OMG!!!!!!!!!!!!!!"

johnjohn2
  • 5763 Answers

SOURCE: replacing turn signal switch in a 2006 Dodge Ram

NO, the steering wheel stays on, all you need to do is remove the covers, look under the bottom cover there will be screws that hold the top and bootom covers together, after you remove the covers you will see two screws that hold switch to column, remove them piull switch out and remove connectors and then install new one, heres a picture of the switch to help you, good luck, hope this helps.johnjohn2_15.gif

Posted on Nov 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Left rear turn signal on dodge ram 1500 won't work. bulb replacement didn't help.


Just had a similar question last week, and the solution was a bad socket/bulb holder.
You might try and see if there is current in the brake light wire leading to the bulb holder.
I have used a jumper wire and a safety pin to test the wire behind the socket.
I pierced the plastic insulation of the brake light wire with the point of the safety pin, and either use a tester or even a good working bulb and a good ground wire.
Be blessed.

Jan 27, 2013 | 2006 Dodge Ram 1500

2 Answers

Dodge ram 3500 turn signal - headlight problem


WAY TO GO !!! another "great idea" from vehicle manufactures

Jun 07, 2012 | 2004 Dodge Ram 3500 Truck

1 Answer

Turn signal dosent work


you need to check to see which bulbs don`t work both front and back lights for the signal on the side it`s not working,you don`t say if any signals work or not if no signals work then you need to check the fuses under the dash on the driver`s side.now if it`s just one side then check the lights as mentioned above.if one isn`t then replace the bulb.if neither bulb is working then it sounds like the signal flasher is not working.turn on the hazard flashers and check the lights front and back.if all bulbs work then leave the hazards on and look under the dash for the flasher that is making the noise,this will show what the signal flasher will look like,then find the signal flasher on the fuse panel under the dash it should be located on the fuse panel.and replace

Mar 15, 2011 | 1997 Dodge Ram 1500 Club Cab

1 Answer

2002 ram 1500 single cab ext light issues


sounds like a faulty underhood fuseblock..have seen lighting issues with these components

Jul 16, 2009 | 2004 Dodge Ram

1 Answer

Turn signals and hazard lights quit working on 2001 dodge ram


The only thing left to investigate is the signal switch itself. The brake light system runs through the signal switch so it can effect both systems. Start with the simple, like, is a wire loose? Look at the base of the steering column. Check plugs and such. I believe you'll see it's in that part of the system.

Good Luck

Feb 27, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

My hazard lights and turn signals stopped flashing


i bet you have a bad multi function switch or turn sig switch. good luck

Oct 25, 2008 | 2006 Dodge Ram 1500

Not finding what you are looking for?
Cars & Trucks Logo

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...