Question about 2004 Hyundai XG350

1 Answer

Can starter be removed from above or under vehicle.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 4,977 Answers

Underneath is the way to go.

Posted on Apr 11, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Where is the starter on a 98 blazer


zjlimited_209.jpg

Fig.: Starter mounting location-4.3L and 5.0L engines



The following is a general procedure for all trucks covered in this information, and may vary slightly depending on model and series.

1. Disconnect the negative battery cable at the battery.
2. Raise and support the vehicle.
3. Disconnect and tag all wires at the solenoid terminal.

Reinstall all nuts as soon as they are removed, since the thread sizes are different.

4. Remove the front bracket from the starter and the mounting bolts. On engines with a solenoid heat shield, remove the front bracket upper bolt and detach the bracket from the starter.





Hope helps (remember to rate and comment this)..

Dec 12, 2010 | 1998 Chevrolet Blazer

1 Answer

How do you remove and replace a starter for a 1992 2.6L Isuzu Amigo?


1.The battery negative and more importantly positive cable must be disconnected.
2. There are 2 14mm bolts holding the starter in place, the upper bolt can be removed by leaning over into the engine compartment from under the hood with a socket and extension on a ratchet or a ratcheting wrench.
3. crawl under the front passenger wheel and remove the positive cable nut, remove positive cable from starter.
4. unclip the small ground wire attached to starter.
5. remove the lower starter bolt.
6. There is room on the bottom of the vehicle to wiggle the starter down to the floor and out from under the vehicle. There isn't enough room to get the starter out from the engine compartment up and out from under the hood.
7. installation of new starter is reverse of installation.

This procedure should work on any Isuzu Rodeo, Trooper, Amigo, or Honda Passport with a 2.6L 4 cylinder 4ZE1 engine

Nov 12, 2010 | 1992 Isuzu Amigo

1 Answer

How would i remove a starter from under the hood?


You cannot remove starter from under the hood.
The starter can be removed from under the car. The procedure is:
Disconnect the battery. Raise the front of vehicle, and securely support on jack stands.
Remove the transaxle driveplate/torque converter cover. Disconnect the wires from terminals on starter, and solenoid. Remove the starter mounting bolts and remove the starter from the vehicle.
Installation is the reverse of removal.

Oct 21, 2010 | 1999 Chevrolet Venture

1 Answer

LOCATION OF FUEL FILTER ON A 1985 TOYOTA FOUR RUNNER\r\nWITH A 22RE ENGINE


It is well hidden. You can find it by laying under the front of the vehicle and looking up at the engine block on the passenger side just above the starter. It is bolted to the block directly above the starter and just below the intake manifold. This is not an easy job. Depending on you skills as a contortionist and tools on hand, you may have to remove the starter and the oil filter to get to it.

Aug 14, 2010 | 1985 Toyota 4Runner

1 Answer

Starter replacement on 1997 dodge intrepid


Disconnect battery negative cable Remove and Install Battery Cable
Raise vehicle.
For easier servicing, do not remove the wiring from starter at this time.
Remove three starter attaching bolts from engine/transaxle Starter -
Remove starter assembly from transmission housing. Position the starter to gain access to the wiring connectors.
Remove the battery positive cable nut from starter and remove the cable Wire Terminal Connections .
Remove the starter from vehicle.
INSTALLATION
For installation, reverse the above procedures. Clean corrosion/dirt from the cable and wire terminals before installing wiring to the solenoid.Thank you for using FixYa,Lee Davidian

Jan 11, 2010 | 1997 Dodge Intrepid

2 Answers

Whers is the starter on a 1996 saturn sl and what is the best way to replace it


Just is one way to replace. Review this:

1996 Saturn SL 1.9L MFI SOHC 4cyl

1fe174c.jpg

If the starter is to be replaced, remove the bracket from the old starter

REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. If equipped, remove the starter shield pin by pulling on it with pliers, then lift and release the shield from the solenoid.
  4. Spray the solenoid electrical connection nuts and studs with penetrating oil, and allow it to seep in for a minute to loosen the connections. While the oil is soaking in, tag the solenoid electrical connectors for identification during assembly.
It is very important that the solenoid electrical connection nuts and studs are sprayed with penetrating oil prior to removal to avoid damage to the solenoid end cap. A cracked cap will allow debris and moisture to enter and corrode the solenoid contacts.
  1. Carefully loosen the bolts and detach the starter electrical connectors. Position the wires to the side and out of the way.
  2. Remove the lower starter mounting bolt.
  3. Using an obstruction wrench, remove the upper starter mounting bolt. If the upper starter mounting bolt cannot be reached from below the vehicle, it may be accessible from above, through the intake manifold support bracket opening.
  4. If equipped, remove the bolt attaching the starter rear support bracket to the vehicle. Rotate the starter until the bracket misses the axle shaft support bracket.
  5. Carefully support the starter, pulling it rearward and toward the left side of the vehicle to remove it.
To install:
  1. If equipped on the old starter, install the rear starter support bracket to the new starter. Tighten the bracket nuts to 7 ft. lbs. (9 Nm).
  2. Guide the starter into the bell housing and rotate the assembly until the lower bolt hole in the starter aligns.
  3. Verify that the bracket is properly aligned and loosely install the bracket bolt, then loosely install the starter mounting bolts. It may be necessary to raise or lower the vehicle for access to both the upper and lower bolts, but do not tighten any bolts until all of the mounting bolts have been started.
  4. Tighten both upper and lower starter assembly attachment bolts to 27 ft. lbs. (37 Nm).
  5. Reconnect the electrical wires and install the nuts. Be careful not to overtighten the nuts and crack the solenoid end cap. Route the wiring cable so it will not contact any rough surfaces. Tighten the starter positive terminal nut to 89 inch lbs. (10 Nm) and the solenoid terminal nut to 44 inch lbs. (5 Nm).
  6. If equipped, install the starter shield and push pin, being careful that the pin is positioned for possible future removal.
  7. Lower the vehicle.
  8. Connect the negative battery cable and verify operation.
15aebbb.jpg

Fig. Remove the starter motor dust shield retaining clip


75381aa.jpg
Fig. Lift off and remove the starter motor dust shield from beneath the vehicle


98d7fb8.jpg
Fig. Loosen the starter solenoid wiring terminal screws ...

f05fd78.jpg

Fig. ...then label and disengage the wiring harnesses from the starter solenoid, carefully positioning them out of the way


348d2a8.jpg
Fig. Loosen the lower starter motor mounting bolt ...


46ba7f0.jpg
Fig. ...then remove the bolt from the vehicle


08946b5.jpg
Fig. If accessibility is limited from below the vehicle, use the opening in the intake manifold support bracket to reach the upper starter bolt

3233aaf.jpg

Fig. Remove the rear mounting bracket bolt, then remove the starter from the vehicle




I hope help you with this (remember rated this help) Good luck.

Oct 16, 2009 | 1996 Saturn SL

1 Answer

How hard is it to put a new starter on a 2002 Gmc Sonoma


The procedure to replace a starter is given below:
  1. Disconnect negative (black) battery cable.
  2. Jack up the Truck on stands.
  3. Remove front right tire.
  4. Access starter from wheel well.
  5. Remove cable from ignition and positive cable coming from battery.
  6. Crawl under the passengerside near the front wheel remove two bolts on the starter. pull starter out from wheel well.
  7. Installation is reverse.
  8. You can possibly do the above from underneath the vehicle, but not sure if starter will drop down.

Sep 20, 2009 | 2002 GMC Sonoma Extended Cab

1 Answer

Trying to remove the starter on a 1991 SaturnSL


no there is not a special tool need more info go to collisionrepairadvice.com for more
1991 Saturn SL L4-1.9L DOHC VIN 7 Vehicle Level a_003366.gif Starting and Charging a_003366.gif Starting System a_003366.gif Starter Motor arrow1.gif Service and Repair arrow2.gif blnk_spc.gif Service and Repair Notes
  1. Disconnect battery ground cable.
  2. Remove air inlet tube and fresh air hose, on DOHC models, lift resonator upward to disengage from engine support bracket.
  3. Remove upper starter attaching bolt through access hole near intake manifold support bracket.
  4. Raise and support vehicle.
  5. Using suitable pliers, remove starter shield pin, then lift shield upward to release from solenoid.
  6. Disconnect starter electrical connectors and position aside.
  7. Remove lower starter attaching bolt.
  8. Remove rear starter support bracket attaching bolt.
  9. Rotate starter until bracket clears axle shaft support bracket, pull rearward toward lefthand side of vehicle to remove.
  10. Reverse procedure to install. Torque starter attaching bolts to 26 ft. lbs., starter bracket bolts to 22 ft. lbs. and starter solenoid terminal to 3 ft. lbs.

Apr 11, 2009 | 1991 Saturn SL1

2 Answers

Can't find the starter in a dodge spirit 1989


Taken from Haynes repair manual. I used these instructions myself to replace starter motor on my 1989 Dodge Spirit after nearly going berserk at three attempts to remove it without wanting to look it up in book.
1)Detach the negative battery terminal. 2) Working from above the engine, remove upper mounting bolt and nut to starter. (Access is accomplished this way: stand on driver-side fender and look down at brake fluid reservoir. Just below and beyond the brake reservoir you will see a vent hose. Disconnect hose & remove. Now you will see the starter motor from above view. You will be able to see a mounting bolt and a nut connecting starter to engine just above the starter (facing brake reservoir). Remove (1) bolt & (1) nut first, then raise vehicle and suport on jackstands. Then go underneath the vehicle and remove the remaining lower mounting bolt (1) on the starter. Label wires then detach them from starter. Now you can remove the starter. If you find it a tight squeeze, you may want to remove or swing the transaxle on that side for additional access, although that is not mentioned in manual (but I did it). It just gives you more room, but does not seem absolutely necessary. 3) Installation is reverse of removal.
please do rate the solution.
thank you for using fixya.

Feb 09, 2009 | 1989 Dodge Spirit

1 Answer

1999 Chevy Blazer Starter


the starter is located on the passenger side lower motor. it has two bolts in it that hold it in place. it actually goes through a hole/slot in the transmission to the flex plate.

1st. disconnect the negative cable on the battery.
2nd. raise the vehicle safely and place a jack stand under the vehicle out of your way but near where you will be working(for safety).
3rd. remove the two bolts that hold the starter in place.
4th. remove the wires from the back of the starter.
5th. install in reverse order of above.

note: there may be little plates between the starter and the mounting points called shims. if there are then make sure you put them back.

Sep 24, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
2004 Hyundai XG350 Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...