Question about Cars & Trucks

1 Answer

How do you replace the fog light assembly on a 2000 Doge Neon?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,218 Answers

The fog light is bolted to the back side of the bumper/skin assembly. You have to get underneath the vehicle and remove the bolts that secure it.

Posted on Apr 11, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the fog light? what needs to be removed to access fog lights and side marker lights.?


SECTION 417-01: Exterior Lighting 2000 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 08/27/1999 Fog Lamp Removal and Installation
  1. Raise and support the vehicle. For additional information, refer to Section 100-02.
  1. Remove the aeroshield-to-sub frame screws.
    a0008736.gif
  1. Remove the seven screws and remove the aeroshield.
    a0009383.gif
  1. Disconnect the fog lamp assembly electrical connector.
    a0011782.gif
  1. Remove the fog lamp assembly.
    1. Remove the screws.
    1. Remove the lamp assembly.
    a0011783.gif
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n161420&c35=wsm%2cfog%20lamp%2csyh%2c417-01%2cremoval%20and%20installation&s=1249x702&c=32&j=1.3&v=y&k=y&bw=910&bh=359&ct=lan&hp=n&[aqe]

Mar 05, 2011 | 2000 Mercury Sable

1 Answer

Can't find the crank sesnor on doge neon where could I find it


Look on engine block, behind alternator, just above oil filter.

Aug 30, 2009 | 2000 Dodge Neon

2 Answers

My car( neon 97) didnt have fog lights originaly and i dont know how to instal it


its not a bad job on a neon ,the fog light kit you will buy will come with a switch and the relay and wiring for installing them,they also came with a real good set of directions for doing this,if you need to get someone to help you with doing this,sometimes running the wires is tricky,but other than that the fog lights can be mounted in the same place as the originals was,and they look good,i sold my 97 neon and i had fog lights on it,they were after market but looked and worked excellent,with a little work and time anyone can install a set on any car,good luck.

Jul 25, 2009 | 1997 Plymouth Neon

1 Answer

Changing fog lights


you can take loose the black plastic shield that runs from inner fender to bottom of bumper. once loose you gain access to back of fog light where mounting bolts are located if its just the bulb your replacing you can also do that without removing it

Jun 28, 2009 | 1998 Dodge Neon

1 Answer

2002 doge neon r/t revs itself when i start it


The most common source of that problem is a sticking idle control motor. As a first step, purchase a new gasket and/or O-ring for the idle control motor. Remove the motor and clean it out using aerosol carburetor cleaner. If the idle control motor was sticking, that should cure it. It the fix only lasts temporarily, you need to replace the idle control motor. This is a common problem with vehicles with over 80,000 miles on them.
Charlie

Jun 18, 2009 | 2002 Dodge Neon

1 Answer

How do you replace the fog lamp on a 1997 dodge neon? As best as I can tell, you have to take off the front bumper which I hope is not the case.


To replace the fog light of the passenger side you need to remove the fog light bolt and pull out the fog light assembly, then you can remove the bulb and put a new one in.

To replace the fog light on the driver side you will need to remove the front bumper cover so you can remove the vacuum box that is in the the way of the fog light bolt.

To do so you need to remove the Torx (star) screws located in the front wheel wells as well as the bolts holding the plastic by the radiator. "CAUTION: DO NOT UNBOLT THE RADIATOR."

If any of the screws are rusted into place put some penetrating oil them to help loosen them up.

PLEASE DON'T FORGET TO RATE!!!

Mar 16, 2009 | 2002 Chrysler Voyager

1 Answer

How do i change my fog lights to my 2004 dodge neon


you need to remove the 2 nuts from under the fascia that hold the assembly in. this will give you access to the bulb

Jan 11, 2009 | 2004 Dodge Neon

1 Answer

Replacing 2000 toyota avalon fog light bulb


o easy enough just jack frontcar up use jackstand for safety now loo up under the bumper where fog lights sit depending on style fog light u might need to pull the whole assembly out or just twist the bulb not a hard task once u see it from underneath it is pretty easy

Dec 02, 2008 | 2000 Toyota Avalon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...