Question about 1995 Mercury Villager

Open Question

What windshields can be used in a 1995 Mercury Villager?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: Mercury Villager headlight assembly diagaram for removal

This is easy. Lift the lid open. Look at the back of the sealed beam and you will see a clip and an o ring. Pull the clip up and pull wires back toward the driver's seat. Unscrew the o ring and firmly pull the bulb out toward the driver again. Note the 3 tabs on the bulb seat and realign the new bulb with those tab ( 2 bottom, 1 top). Replace with #9007 bulbs..do them both.

Posted on Dec 12, 2008

emissionwiz
  • 75822 Answers

SOURCE: location of the engine diagnostic connector 1995 village mercury

The diagnostic connector is located on the engine near the starter. However, there are four connectors in that location and without pictures it would be difficult to determine which is the proper one

Posted on Mar 08, 2009

mcgyver468
  • 710 Answers

SOURCE: Tune up needed

okay, should be fairly simple. plugs, wires, cap, rotor. This vehicle has a nissan motor in it. Maybe purchasing a service manual for this minivan wil help a whole lot. Good luck

Posted on Apr 23, 2009

  • 249 Answers

SOURCE: I have a 1995 Mercury Villager. Replaced the engine and tranny.

sounds like you bought a bad tranny,was it a used 1 you bought?

Posted on Jun 19, 2009

techbuster
  • 5081 Answers

SOURCE: replace heater core 1995 Mercury Villager

Unfortunately, this is one of the most complex and time consuming operations, short of changing the engine/transmission that can be done to the car.
The heater core is mounted in a box, inside the passenger compartment, almost dead center behind the dashboard and is mounted directly on the firewall to allow the hoses to go through. If you put your hand just above the accellerator pedal, and go toward the center console, you'll find the heater core box.
There is no way to remove the heater core from the engine compartment. In fact, other than draining the radiator and removing the hose clamps and a bolt or two, youll have little interaction with the engine compartment.
Begin by disabling the air bag system, by removing all power from the vehicle. Be SURE the air bags are disabled as they are extremely dangerous if they activate while you are working under the dash.
Next remove the entire instrument panel, and all the decorative plastic. To do this you may have to remove the steering wheel also. Be sure to label everything as you go. Then remove all the heater controls. Once done, you should be able to access the black heater box that the core rests in. Remove that, and if you have loosened the hoses and screws in the engine compartment, the heater core will come free and you can replace it.
For a much better and more detailed explanation of how to do this, I used the Haynes Repair Manual. (Note, Im not affiliated with them, they just had the best description of the procedure.)
I dont really recommend doing this yourself unless you are a very patient and reasonably accomplished mechanic. This will involve removal of all the dash, instruments and controls, and frankly, even when the dealer did this, the car is never quite the same again.
One other hint, after replacing the heater core, use a length of good heavy copper wire to wrap around one of the hose entry points (metal to metal contact) and then ground the core to the engine block or frame. This will help prevent the electrolysis that killed the core the in the first place.

Posted on Oct 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a mercury villager 1995 and need to know where I can get the bottom of the transmission tray.


Your Mercury Villager is so old (in vehicle years) you may have resort to searching through junkyards to find a used part.

Jan 28, 2015 | 1995 Mercury Villager

1 Answer

I can not open my 1995 mercury villager


no switch in van. Spray with penetratingoil & see if it loosens up.

Fixed back glass or does glass open? Handle on back glass?

Go here

http://groups.yahoo.com/group/villagerquest/

Jul 28, 2010 | 1995 Mercury Villager

1 Answer

I have a 1995 Mercury Villager. Replaced the engine and tranny.


sounds like you bought a bad tranny,was it a used 1 you bought?

Jun 19, 2009 | 1995 Mercury Villager

1 Answer

Smell of gasoline in cold starts


call a Mercury dealer and give him your 17 digit VIN number and ask him to check for any recalls. If yes, they are free,
Also, this site has files on most Villager & Quest problems.

http://autos.groups.yahoo.com/group/villagerquest/

Jan 19, 2009 | 1995 Mercury Villager

1 Answer

Windshield wipers wont turn but the wiper motor runs


you likely broke the plastic gear inside the wiper motor by turning wiper on when wipers were frozen to glass. you will have to replace the motor.
you can buy motor on Ebay cheap.
you have to remove screen at bottom of windshield for access. remove side windshield mouldings to be abe to get screen off.
watch very, very carefully how you get wiper linkage out or you will have a hard time getting it back in.

Jan 10, 2009 | 1996 Mercury Villager

5 Answers

Mercury Villager headlight assembly diagaram for removal


This is easy. Lift the lid open. Look at the back of the sealed beam and you will see a clip and an o ring. Pull the clip up and pull wires back toward the driver's seat. Unscrew the o ring and firmly pull the bulb out toward the driver again. Note the 3 tabs on the bulb seat and realign the new bulb with those tab ( 2 bottom, 1 top). Replace with #9007 bulbs..do them both.

Jul 01, 2008 | 1995 Mercury Villager

Not finding what you are looking for?
1995 Mercury Villager Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...