Question about Cars & Trucks

2 Answers

2003, replaced mastercylindar, but can't get pressure to hold

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Cars & Trucks Master
  • 773 Answers

You obviously have a leak somewhere... put some clean, flattened cardboard under you car and wait until tomorrow and then look for spots. Make sure each wheel is under the cardboard as well as the Master Cylinder. Brakes lines and/or the Master Cylinder gasket are what I would suspect.

Posted on Apr 10, 2015

  • rita hendricks Apr 12, 2015

    Thank you Robert, but it turns out that the leak was beneath the truck at the ABS. connection of the mainline to the rear of the vehicle,, .... $600.00. later, my truck is fixed & back home

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Cars & Trucks Expert
  • 236 Answers

Did you bench bleed first ?

Posted on Apr 11, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need tire pressure for 2003 Chevy Impalla


It is printed on the sidewall of the tire. The pressure listed is the maximum amount of air the tire can hold. Do not fill the tire to its maximum. Fill the tire five pounds less so that the tire can get hot and not build up excessive air pressure. An example would be a listed pressure of 40psi max. Keep the tire at 35 pai. Good luck!

Oct 30, 2016 | 2003 Chevrolet Impala

1 Answer

No fuel pressure, on 2003 Grand Am could it be anything becides the fuel pump?


I would check the fuel relay and or fuse and if there are good replace the pump.

Dec 10, 2011 | 2003 Pontiac Grand Am

1 Answer

2003 Lincoln LS transmission shifts hard at times. Feels like it's coming out of the car....any ideals


Replace the Solenoid Pressure Control Pack
inside the trans pan

Remove the bottom pan
Remove the filter
Remove ( 1) 10mm bolt holding
wiring harness
Remove 7 bolts holding Shift Pack

HPN-9L2Z7G391A $515.30 List /$332.20 Wholesale,
that is at the trans parts supply house

Don't even go to a Lincoln Dealer --say no more

Do not use the car until resolved,SAVE The Trans

Jun 11, 2011 | 2003 Lincoln LS

1 Answer

How do i reset the low tire pressure light on a 2003 buick rendenvous


  • Follow these steps
  1. Turn the vehicle off while holding the mode button on the information center until it says "Low Tire Pressure Press To Reset"
  2. Then press and hold the "set" button until the chimes go off and you see "Tire Pressure Reset."
  3. The chimes should then sound three times and "Tire Pressure Normal" will display.
  4. That's it.
  • Do this only AFTER you fill the tire so it will recognize the level as being low compared to the pressure after you filled the tire.

regards, Tony

May 17, 2011 | 2003 Buick Rendezvous

1 Answer

2003 passat starter


Does it still crank over, if so you may have a problemwith your tandompump not holding fuel pressure at the back of the head, the lift pumpin the tankis feeding it but after a while the fuel is falling back to the tank instead of holding pressure in the tandempump, checkit out.

Feb 02, 2010 | 2003 Volkswagen Passat

2 Answers

Step on brake steering shake


Could be any number of things here: alignment; bad caliper; warped rotor.

Oct 09, 2009 | 2003 GMC Yukon XL

1 Answer

I have 2003 kia spectra startup problem *need help*


bad fuel tank pressure sensor-replace, and a new Kia brand gas cap.

Sep 05, 2009 | Kia Spectra Cars & Trucks

1 Answer

My 2003 pt cruiser keeps losing tire pressure..took back to the dealer twice and they said they did somethig to the rims because they were rusting but does not seem to hold pressure even with nitro in the...


your rims are too badly rusted to get a good seal between the tire and rims.  You need to replace the defective rims.  This is a good time to buy some fancy rims or used ones from a junk yard. 

Mar 26, 2009 | 2003 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...