Question about Mercury Cars & Trucks

1 Answer

Can you show me a photo where my transmission control module is located on a 99 mercury sable

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Mercury Master
  • 531 Answers

1999 Mercury Sable Auto Trans Control Solenoid Standard Motor Products...

otherwise, the ECU or ECM controls the whole vehicle

Posted on Apr 10, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 899 Answers

SOURCE: no heat/99 mercury sable

its not a fuse if the blower motor works , you have a clogged or bad thermastat, bad water pump or your radiator heater core is clogged

Posted on Nov 25, 2008

jrw4u
  • 62 Answers

SOURCE: Transmission Control Module

Before condemning the transmission, I would check the shift cable for proper operation. Look at the side of the transmission where the shift cable attaches. Have someone shift the transmission from PARK to FIRST. The engine should not be running. If the operating lever on the transmission moves, then you probably do have an internal transmission problem. 78151957.gif
If the operating lever does not move, you have a broken shift cable or it has popped of it's attachments at the operating lever or gear shift handle.
78151960.gif
A bad Transmission Control Module (TCM) would not keep it from shifting. In the event of a bad TCM, the transmission would go into fail safe mode and you could continue driving the vehicle.

Posted on Apr 28, 2009

  • 436 Answers

SOURCE: Where is the wiper delay control module located on

the module is located under drivers side dash right of the steering column. it is gray plasticmodule, the most common problem with these modules is soldering on the board. If you resolder these points the module should work for you.

Posted on Aug 25, 2009

  • 163 Answers

SOURCE: fuel pump relay location on 98 mercury sable

its under the hood on driver side what the problem not starting check the trunk area for the fuel cut off switch poss bad or tripped did u get hit or someone bump ur car

Posted on Mar 28, 2010

alicantecoli
  • 22219 Answers

SOURCE: firing order for 99 mercury sable 3.9 v6

153624

Posted on Apr 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 mercury sable transaxle light is flashing and jerks when trying to go forward seems to move ok in reverse.


You need to the transmission control module scanned for fault codes, one is recorded whenever the light starts flashing.

Mar 16, 2017 | 2002 Mercury Sable

1 Answer

What does it mean when my transaxle light comes on I have a 2000 mercury sable


It means that the Transmission control module has detected a fault in the operation of the transmission or its controls. You now need it scanned to see what fault code or codes was set in the memory of the TCM.

Sep 29, 2016 | 2000 Mercury Sable

2 Answers

1995 mercury sable....what is the cause of the fan not working


possible causes, fan motor, fan relay, on no power in that circuit

Sep 30, 2010 | 1995 Mercury Sable

2 Answers

Where is the ignition control module located on a 1995 mercury sable 3.0 v6


For 1995 Mercury Sable 3.0L EFI 6cyl the Control Module-Ignition is located: Under hood, center, upper engine area, mounted on side of distributor.

Hope helps (remember rated this).

Aug 11, 2010 | 1995 Mercury Sable

1 Answer

Code p0230 shos up on my 99 Mercury Sable. I just


That code is: Fuel Pump Primary Circuit Malfunction. Could it be the wires are not on tight or one is shorted? Check wiring very carefully.

May 19, 2010 | 1999 Mercury Sable

1 Answer

1996 mercury sable computer


If you are looking for the powertrain control module (PCM) it is located in the right rear corner of engine compartment ( Passenger side), mounted in Firewall

Sep 10, 2009 | 1996 Mercury Sable

1 Answer

Where is the wiper delay control module located on a 1997 Mercury Sable GS?


the module is located under drivers side dash right of the steering column. it is gray plasticmodule, the most common problem with these modules is soldering on the board. If you resolder these points the module should work for you.

Aug 25, 2009 | Mercury Sable Cars & Trucks

1 Answer

1999 Sable quits shifting when it gets hot


How do you know it's getting hot ? What is the Temp gauge showing ? Do the cooling fans work ? Have it checked for trouble codes an scan data checked .
It was however the correct thing to do in changing the fluid and filter - that's the first suspect. No no it wasn't , the correct thing would be to take it to a qualified repair shop . Hooking up a professional type scan tool an viewing data , inputs to transmission control module , ECM/PCM - engine computer etc. The control module controls shift solenoids -which shift the transmission . You could have 1-2 shift solenoid shorting when getting hot . View scan data is the only way to see this problem .

Jul 22, 2017 | 1999 Mercury Sable

2 Answers

99 sable


The transmission is should be controlled by the tcm "transmission control module". The first item to check would be a good visual inspection. If all seems in the norm, then the fluid condition and level. You have to check the transmission level when the car is running at operating temp and in park. If that is ok, the next item would be to have the code read. Autozone will scan your car for free. Once you have a code, it may give a hint as to what system is acting up. That is where I would start.

Dan

Sep 04, 2008 | 1999 Mercury Sable

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...