Question about 2005 Chevrolet TrailBlazer

1 Answer

Three wires two positive one neg opne pos hooked up goes to fuessbox theres one pos wire off doess it neeed to go on

Three wires from fuess box two positive and one negative two hooked up one poss left off does it need to be on

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has answered 20 or more questions within one hour.


    An expert who has answered 20 questions.

  • Expert
  • 111 Answers

Need to find a vehicle like yours and look for those wires

Posted on Apr 15, 2015


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 36 Answers

SOURCE: 1984 chevy 350 wiring

The positive cable from the battery goes to the starter, the negative cable goes to either the frame or the block

Posted on Jan 03, 2009

  • 10 Answers

SOURCE: wiring was left off my 2000 chev cavalier at the

big one is possitive little one for igniion switch

Posted on Jan 28, 2010

  • 1 Answer

SOURCE: What colour wire is the stoplight feed that feeds the stop lights

Could I get a copy of those wiring diagrams? I am installing trailer hitch and need to wire the 4 flat.

Posted on Apr 08, 2010

  • 977 Answers

SOURCE: i am trying to install a backup camera but i need

it does'nt really matter as long as you know which one is positive because you can run the earth wire from camera to any metal part of the vehicle......hope this helps.....cheers.

Posted on Jun 13, 2011

  • 3 Answers

SOURCE: i really need wiring diagram for 2005 suburban rear brake lights.

Use a voltmeter to determine which is the hot wire

Posted on Feb 28, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Reemoveing six six volt batteries and replaceing them with three 12 volts in the nss burnisher and how to hook up the cables

If the 6 volt batteries are wired neg to pos to neg to pos to neg etc, then do the same with tha 12 volt batteries. So neg on one to pos on the next, then neg on that one to pos on the third. (- +) (- +) (- +)
\..../ \...../

Dec 07, 2017 | Cars & Trucks

1 Answer

What colors are the Speaker Wired for a 1993 gmc 1500 van

    1. OK,GMC/GM are wired as such. White/Black wire, front left -[neg] White, front left +[pos]. Grey/Black wire, front rt -[neg], Grey wire, front rt +[pos]....Green/Black wire, left rear [neg], Green, left rear [pos]....Violet/,Black , Rt rear [neg],...Violet, Rt.rear [pos]........You will also have a Blue/Red wire that goes to antenna. ..A Blue wire for Power Remote....Red goes to IGNITION.....Yellow goes to Battery[for clock].....And finally a Black goes to Ground.......I hope that you have good luck and everything works out for you. `

Sep 07, 2015 | GMC Cars & Trucks

1 Answer

How do I hook up this unit Two wires or four

Almost all car batteries have 2 pos and 2 neg. More precisely, 1 pos post and 1 side connector, 1 neg post and 1 neg side connector. You only usually use use one set or the other depending on what connectors are on the end of your cables. You can connect something else to the side posts if you need to, but generally only pair is used.

Feb 28, 2015 | Cars & Trucks

1 Answer

Convert battery cables from top post to side mount replacement ends?

If all you are doing is changing to a side post battery, just connect all the positive cables from the old pos post to the new pos holder and all the neg ones to the new neg holder. If you've already cut them all off and not sure where each wire goes, all the reds are positive, all the blacks are neg. To make sure use your continuity meter to test. Connect one meter lead to any good clean metal part on the car and test between each black wire in turn, the neg ones will show a circuit, the pos ones will not.

Feb 10, 2015 | 1993 Chrysler Concorde

1 Answer

Is it hard to replace a starter? Is there instructions on internet.

replacing starters is pretty much the same in any motor,, unhook the battery , Neg first then Positive, ( always ) Locate the starter,, there are 2 bolts that mount the starter on your vehicle, and the power hook up wires, if you can get to the wires first, disconnect them,, if not,, you may have to loosen or remove the starter first . ( make sure you remember which wires go where, ) unbolt the 2 bolts and slide the starter out of the housing, replace it the same way ,, be sure and hook up the battery POs first then Neg ( this is done this way to make sure the air bag system discharges correctly, )

Oct 01, 2011 | 1993 Saturn SL1

2 Answers

What is malfuntion code P2127?

the (app sensor)accelerator pedal position. to test unplug the electrical connector at the accelerator pedal position sensor. Using a digital multimeter and with the key in the RUN position, check the Green wire for 5 volts (pos lead from meter to green wire, neg lead to ground). Then check the black/white wire for good ground (pos lead from meter on Green wire, neg lead to black/white wire)--should read 5 volts. Reconnect electrical connector to sensor.


Oct 26, 2010 | 2004 Hyundai Santa Fe

1 Answer


make sure you have holes in bumper you can run wires through firewall and tie into fuse block+pos wire goes to at least a 20amp fuse and other side toswitch +pos wire from lights goes to other side of switch -neg wire goes to suitible body ground in engine compartment fender bolts use eyelet conector or you can attach to neg term of battery.royedwardtat

Jul 13, 2009 | 2007 Toyota Camry

1 Answer

2000 dodge durango-i replace the blower motor and i get nothing. the negative wire is reading with positive power. Why is this??

you have the wires backwards, switch them up you probably have the pos. to neg. and the neg, to pos.

Mar 31, 2009 | 2000 Dodge Durango

2 Answers

Need help Jump statring

Red is positive. Black is negative. Negative goes to ground (car body and engine block). Positive goes to the starter.

Jan 19, 2009 | 1990 Mazda MX-5

Not finding what you are looking for?
2005 Chevrolet TrailBlazer Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides