Question about Cars & Trucks

1 Answer

Where is the oil pressure sending unit on a 95 chevy s10 4.3

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Expert
  • 38 Answers

The oil pressure switch is mounted to a fitting in the left rear of the engine block.

Posted on Apr 10, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chevy 350 oil pressure sending unit


The Oil Pressure Switch is located:Under hood, center, rear engine area, driver side of distributor, mounted in block. Here's what it looks like.he oil pressure switch is mounted to the top rear of the engine.

  1. Remove the electrical connector from the switch.
  2. Remove the oil pressure switch.
  3. To install, reverse the removal procedures.

Jul 18, 2013 | Cars & Trucks

1 Answer

Location 95 chevy pu oil sender unit


Should be between the intake manifold and the firewall near the distributor.

Feb 24, 2013 | 2001 Ford Ranger Regular Cab

1 Answer

I have a 1976 buick regal 350 engine and the oil light comes on when the engine gets hot and it is at an idle. when you give it gas the light goes out. could this be the oil sending unit and if so where is...


it might be the sending unit, is it a buick 350 or a chevy. 350? if a buick engine the sinding unit should be on the side of the timing cover if a chevy 350 next to the dist.

remove the oil sinding unit and install a manuel gauge and see just what the oil pressure is if below 10 psi at hot idle replace the bearings and oil pump in the engine. if this is a chevy 350 make sure you replace the camshaft bearings this is were we use to see the gratest oil pressure loss.

Aug 20, 2011 | Buick Regal Cars & Trucks

1 Answer

98 chevy 1500 starts and then shuts right off have replaced fuel pump and filter ,crank sensor,cam sensor ,oil sen. coil,ign.mod and PCM


On some chevys the oil pressure sending unit closes the circuit to continue the fuel pump to run after start. In the event of a wreck ,the car stops running thus no oil pressure thus turns off power to the fuel pump .A safety to help prevent fires. When you first start the car, the computer turns on the fuel pump for about 20 seconds just enough time to start and allow the oil pressure sending unit to close the circuit to allow it to continue running. when the car car has NO oil pressure or the sending unit fails ,it will start then shut down..as many times as you try to start. replace the oil pressure sending unit and secure a good conection. Dan

Feb 13, 2011 | 1998 Chevrolet C1500

1 Answer

Hello, I have a 95 aurora and its not a noisy car, but when at an idle it loses oil pressure. I was told i may either have to get an oil pressure sending unit or switch to 10w40 oil? NEED HELP...


I have a 93 Chevy Caviler that does the samething and all it it the gauge on the dash is bad and shows at an idle it has 0 psi but it still runs fine. I have drove this car for 2 years like this and nothing has happen. If your is running fine then your gauge may just be bad.

Dec 23, 2010 | Oldsmobile Aurora Cars & Trucks

2 Answers

I have a 1995 Chevy Lumina with the ''Low Oil'' light on.


may be the oil sending unit is bad
may be the oil pump
is there any noise in the engine?
have the oil pressure check at a repair shop to make sure you have enough oil pressure
if it's ok then have the shop replace the switch while they have the old one out to check the pressure

Mar 09, 2010 | 1995 Chevrolet Lumina

1 Answer

95 grand cherokee oil pressure switch


Use a deep well socket and extension, it lives by the distributor.

Jul 20, 2009 | Jeep Grand Cherokee Cars & Trucks

2 Answers

Volvo 850 oil pressure sending unit


It's on the engine, right next to the starter, it has one wire going to it. You don't need to drain the oil. If the light is coming on, you may have bad seals in the oil pan, a fairly common problem, but replacing the switch is a good fisrt step.

Jan 27, 2009 | 1995 Volvo 850

1 Answer

My 2005 Chevy 1500HD when cold there is no oil pressure accoring to the gauge. But after a few minutes of running and then a restart of the engine the oil pressure is bake to normal.


most likely the problem is the oil pressure sending unit or the oil passage to the sending unit is partially plugged, that is unlikely, I would replace the sending unit 1st.

Jan 15, 2009 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...