Question about 1999 Chrysler Sebring

1 Answer

99 Sebring the code says that the third gear ratio is incorrect. Before it was the shift solenoid. Are there any silly problems that could cause this or am I going to have to rebuild the tranny?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Chrysler Master
  • 460 Answers

I found that when work was done on my chrysler - I had to get Chrysler shop to relearn the tranny its settings. Something did not get set fully after new solenoid installed.

Posted on Apr 10, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does the 99 explorer have a vacuum modulator on the tranny and where would I find the vac hoses off the tranny.


There is no vacuum modulator on your vehicle ! It's controlled by the PCM ,all electronic shift control solenoids ! What DTC'S - diagnostic trouble codes do you have ? P0171 bank 1 lean code ? doesn't mean vac system leak ! could be a vacuum leak but also could be a O2 sensor problem or an intake manifold leak, brake vacuum booster diaphragm leak . What do you mean a slight code of gear three incorrect ratio ? P0733 ? P0733 Gear 3 Incorrect ratio Sorry Jon but you really should take this to a professional !

Jun 08, 2015 | 1999 Ford Explorer

3 Answers

Dodge caravan


Both error codes you have are transmission related. P0736 is an error for reverse has wrong gear ratio. P0700 is a general transmission problem code
http://www.obd-codes.com/p0700
http://www.obd-codes.com/p0736
for more information.

Mar 22, 2015 | Dodge Caravan Cars & Trucks

2 Answers

How to fix a ford f150 with trans fault and flashing overdrive light with diagnostic codes p0731 and p0732>


P0731 Ford - Incorrect First Gear Ratio
Possible causes
- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit

p0732 Gear 2 Incorrect ratio
Possible causes
- Low transmission fluid level
- Dirty transmission fluid
- Faulty Shift Solenoids
- Shift Solenoids harness is open or shorted
- Shift Solenoids circuit poot electrical connection
- Transmission mechanical problems
- Transmission hydraulic control circuit

Start by inspecting the transmission oil level and condition, and change fluid if necessary.

also check OUTPUT SHAFT SPEED OSS for proper installation and function

hope this helps

Sep 16, 2014 | Ford F-150 Cars & Trucks

1 Answer

Need help on p0730,p0780. I have a 00 Acura TL 3.2


code p0730 refers to incorrect gear ratio.==causes --wiring--TR sensors/switch--shift solenoids--transmission mechanical fault
code p0780 refers to gear selection--shift malfunction====causes--wiring--TR sensor---shift solenoids--transmission mechanical fault.. have the shift solenoid checked out. Have a pressure test done on the transmission to check for internal damage.

Nov 12, 2013 | 1999 Acura TL

1 Answer

Transmission service urgent code PO733


code refers to gear 3 incorrect ratio. causes ---wiring---TR sensor/switch--shift solenoids-- transmission mechanical fault. It is not possible to have the wrong ratio unless you have done something serious to the tranny. So the cpu is reading that the gear selected is wrong for the settings in the cpu. This means that the shift solenoid is not working properly and/or the TR sensor /switch is faulty. I would go for the sensor as it probably controls the solenoid as well. Use only genuine as cheaper units are not always compatible with the cpu.

Apr 01, 2013 | 2003 Volvo S80

1 Answer

How to fix problem codes 730-733 laredo 2009


There is no one fix works for all on these code. Also you have left out the letter and one number of the code I assume these are P0730 and P0733, if so read on.

P0730 CHRYSLER - Incorrect Gear RatioPossible causes- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Shift solenoids harness or connectors
- Transmission mechanical problems
- Transmission hydraulic control circuit

P0733 CHRYSLER - Gear Ratio Error In Third GearPossible causes- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit

Jun 27, 2012 | Jeep Grand Cherokee Cars & Trucks

2 Answers

What are the automatic transmission problem codes PO 751, PO 761, PO 734 indicate


PO 734 GEAR 4 INCORRECT RATIO
PO 751 SHIFT SOLENOID A PERF OR STUCK OFF
PO 761 SHIFT SOLENOID C PERF OR STUCK OFF

Jul 05, 2011 | Ford Focus Cars & Trucks

1 Answer

HELLO FRIENDS, I HAVE PROBLEMS WITH MY 2002 EXPLORER LIMITED, THE CHANGE OF THE THIRD SPEED DOES IT TAKE TO DO IT FOR THE FOURTH AND WHEN DOES IT HIT HARD. Scan showed THE CODES P0733 AND P0745. WHAT...


CODE PO733 INCORRECT THIRD GEAR RATIO.POSSIBLE CAUSES.THE THIRD GEAR SOLENOID HARNESS CONNECTOR NOT SEATED.THIRD GEAR SOLENOID SIGNAL SHORT TO GROUND OR OPEN.THIRD GEAR SOLENOID WIRING HARNESS CONNECTOR DAMAGED.THIRD GEAR SOLENOID DAMAGED NOT SEATED PROPER IN PLACE. CODE PO745 TRANSMISSION FLUID PRESSURE SOLENOID CIRCUIT MALFUNCTION.

Feb 15, 2011 | 2002 Ford Explorer

1 Answer

Hi sir, i want some details related to the gear


P0700 Transm.Contr.System Malfunction 17084
P0702 Transm.Contr.System Electrical 17086
P0703 Torque Converter/Brake Switch B Circ Malfunction 17087
P0705 Transm.Range Sensor Circ.(PRNDL Inp.) Malfunction 17089
P0706 Transm.Range Sensor Circ Range/Performance 17090
P0707 Transm.Range Sensor Circ Low Input 17091
P0708 Transm.Range Sensor Circ High Input 17092
P0710 Transm.Fluid Temp.Sensor Circ. Malfunction 17094
P0711 Transm.Fluid Temp.Sensor Circ. Range/Performance 17095
P0712 Transm.Fluid Temp.Sensor Circ. Low Input 17096
P0713 Transm.Fluid Temp.Sensor Circ. High Input 17097
P0715 Input Turbine/Speed Sensor Circ. Malfunction 17099
P0716 Input Turbine/Speed Sensor Circ. Range/Performance 17100
P0717 Input Turbine/Speed Sensor Circ. No Signal 17101
P0721 Output Speed Sensor Circ Range/Performance 17105
P0722 Output Speed Sensor Circ No Signal 17106
P0725 Engine Speed Inp.Circ. Malfunction 17109
P0726 Engine Speed Inp.Circ. Range/Performance 17110
P0727 Engine Speed Inp.Circ. No Signal 17111
P0730 Gear Incorrect Ratio 17114
P0731 Gear 1 Incorrect Ratio 17115
P0732 Gear 2 Incorrect Ratio 17116
P0733 Gear 3 Incorrect Ratio 17117
P0734 Gear 4 Incorrect Ratio 17118
P0735 Gear 5 Incorrect Ratio 17119
P0740 Torque Converter Clutch Circ Malfunction 17124
P0741 Torque Converter Clutch Circ Performance or Stuck Off 17125
P0748 Pressure Contr.Solenoid Electrical 17132
P0750 Shift Solenoid A malfunction 17134
P0751 Shift Solenoid A Performance or Stuck Off 17135
P0752 Shift Solenoid A Stuck On 17136
P0753 Shift Solenoid A Electrical 17137
P0756 Shift Solenoid B Performance or Stuck Off 17140
P0757 Shift Solenoid B Stuck On 17141
P0758 Shift Solenoid B Electrical 17142
P0761 Shift Solenoid C Performance or Stuck Off 17145
P0762 Shift Solenoid C Stuck On 17146
P0763 Shift Solenoid C Electrical 17147
P0768 Shift Solenoid D Electrical 17152
P0773 Shift Solenoid E Electrical 17157
P0790 Normal/Performance Switch Circ Malfunction 17174

Dec 20, 2010 | 2006 Renault Fuego

1 Answer

'99 Concorde won't shift into third. It kind of jerks when it hits second or downshifts into first. Check engine light is on. OBD codes are: P0734,P0731,P0733,P0700


all the codes listed above are saying incorrect ratio for each gear,you should take this to a dealer he can determine which faulty sensor on the transmission is causing this,it is not a internal transmission problem

Dec 24, 2009 | 1999 Chrysler Concorde

Not finding what you are looking for?
1999 Chrysler Sebring Logo

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...